Page 2 - HIGH DEFINITION RECEIVER / RECORDER; USER’S MANUAL
HIGH DEFINITION RECEIVER / RECORDER Model : NHD-3000PVR USER’S MANUAL
Page 3 - Warnings; Important Safeguard
1 Warnings 01 Warnings Read Instructions : All the safety and operating instructions should be read before the product is operated. Retain Instructions : The safety and operating instructions should be retained for future reference. Heed Warnings : All warnings on the product and in the operating in...
Page 5 - About the internal hard disk drive
3 20. 21. 22. 23. Warnings 01 Warnings b) If liquid has been spilled, or objects have fallen into the product.c) If the product has been exposed to rain or water.d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the op...
Page 6 - Table of Contents
4 Table of Contents 02 Table of Contents 01. 02. 03. 04. 05. 06. 07. Warnings Table of Contents Supplied Accessories Controls Front Panel Controls and LEDs Rear Panel Connectors Battery Installation for Remote Control Installation Antenna Input Connection to Digital TV (YPbPr) Connection to Digital ...
Page 7 - Channel
Table of Contents 08. 09. 10. 11. 12. Teletext PIP Control Channel Channel Edit Channel Scan Manual Scan Channel Sorting Channel Duplication Parental Rating Audio/Video HDMI Video HDMI Audio Monitor Setup Digital Audio Out PIP Size Vol. Control PVR Manager Program List Skip Time HDD Sleep Time HDD F...
Page 8 - Supplied Accessories
4. Component Video Cable 5. Audio Cable(L/R) 6.HDMI Cable 7. RF Loop Cable 1. Remote Control 2. Batteries (size AAA) 3. User’s Guide 6 Supplied Accessories 03 Supplied Accessories Make sure the following accessories are provided with product.
Page 9 - Front Side; Front Panel Controls and LED’s; Controls; LED Indicators
Power Menu Exit OK Arrow Buttons Buttons Front Display Power On Power Off EXIT Remote Control Sensor POWER Front Side 7 Front Panel Controls and LED’s Controls MENU Front Display 04 LED Indicators STANDBY TIMESHIFT RECORD OK Arrow Buttons STANDBY Power & Remote Indicator LED Timeshift Playback I...
Page 10 - Rear Panel Connectors; Rear Side
Antenna Input Power Cord 8 Controls ◈ Note. Connection of input/output connector in rear panel should be done while power is OFF. Rear Panel Connectors 04 Connect the cable from an off-air TV antenna to Antenna1 input. Connect Antenna1 loop out to Antenna2 input with RF loop cable. Rear Side Service...
Page 12 - Battery Installation for Remote Control
10 Controls Battery Installation for Remote Control 04 Remove the battery cover and install batteries like the diagram below. 1. Unlatch the battery compartment cover on the back of remote control. 2. Insert 2 AAA batteries as shown, making sure the + and - ends of each battery line up witht h e c o...
Page 13 - Connecting Antenna; Antenna Input; Installation
Connecting Antenna 11 Antenna Input 05 Installation Connect the antenna or RF cable wire directly to ANTENNA1 IN and connect ANTENNA1 Loop Out to ANTENNA2 Input by using RF loop cable. ◈ NOTE · The STB(Set Top Box) should be unplugged before connecting antenna. (Power OFF mode) · The RF OUT from the...
Page 16 - Connection to RGB PC Monitor
Connect the Audio Cables Connect the Video Cables 14 Installation Connection to RGB PC Monitor 05 Connect an audio cable between the L/R Audio output jacks of the STB and the external speakers that contain a sound amp. (Purchase separate jacks for PC speakers.) Connect RGB/HV video output jack of th...
Page 17 - Connect the HDMI Cable
Connect the HDMI Cable 15 Connection to Digital TV (HDMI/DVI) 05 Installation Connect the HDMI/DVI output jack of the STB to the HDMI input jack of the digital TV. In regard to the Video Out Mode, select one of 1080i, 720p, 576p as Video Resolution according to your digital TV. ◈ NOTE · By pressing ...
Page 18 - Connection to HDMI/DVI PC Monitor
Connect the Audio Cables Connect the Video Cables 16 Installation Connection to HDMI/DVI PC Monitor 05 Connect an audio cable between the L/R AUDIO output jacks of the STB and the external speakers that contain a sound amp. (Purchase separate jacks for PC speakers.) Connect HDMI/DVI jack of the STB ...
Page 20 - Connect the Digital Audio Output; Connection to Digital Audio Amplifier
Connect the Digital Audio Output 18 Installation Connection to Digital Audio Amplifier 05 Connect audio cables from the OPTICAL or COAXIAL digital audio output jacks of the STB to theOPTICAL or COAXIAL digital audio input jacks of the digital audio decoder or the amplifier. Do notconnect the coaxial...
Page 21 - Remote Control; Basic Operation
19 Remote Control 06 Basic Operation Aspect Ratio Menu Mute VOL + / - Number Power TV/Radio Favourite CH Add/Del Recall Exit Info / Guide Arrow Left /RightDrag - / + OK Rewind , Fast ForwardStart , End Timeshift , Program List Arrow Up / Down Skip + / - Video Output Video Format Channel List Play / ...
Page 23 - Button
Remote Control (Cont.) 06 21 Basic Operation Button Description Press to change the output video format from one of resolutions, such as 1080i, 720p,576p or 576i ( 576i is not supported In HDMI output) Press to freeze the picture (To return to normal operation, press any button) Displays the recorde...
Page 24 - Channel Information; On Screen Display; INFO; button to display the following screen.
22 Channel Information On Screen Display 07 Press the INFO button to display the following screen. 1. RF Signal Strength 2. Channel Number 3. A/V Info. 4. Current Time 6. Current Program 5. Service Provider and Service Name 7. Next Program 8. Parental Guidance Rating ※ The channel information menu a...
Page 26 - (STATUS) button to display current channel status and information.; Channel Status
07 24 On Screen Display Press MARK (STATUS) button to display current channel status and information. Press MARK (STATUS) button to display main channel status and information. It displays service provider name, service provider title, physical channel number, source video format, output video forma...
Page 27 - Channel List; LIST; button to select channel on Channel List menu.
Channel List 07 25 On Screen Display For channel change, add or delete 1. Press LIST or OK button. 2. Press ▲ , ▼ button to highlight ‘Channel List’. 3. Press OK button to tune. 4. Press ▶ button to add channels to ‘Channel List’ or press ◀ button to delete channels to ‘Channel List’. If channel is ...
Page 28 - Timeshift Control
26 Timeshift Control On Screen Display 07 Press T.SHIFT button to start timeshift. ※ When Timeshift is ON, you can see a logo on the left ( ). If you want to remove this logo, press EXIT button. ※ Timeshift has to be at least about 1 minute recording. ※ Timeshift runs about 1 hour. ※ Timeshift is un...
Page 30 - Timer Record List
28 Timer Record List On Screen Display 07 Show the Timer Record List. ※ The T.REC button is recorded at Tuner #1 (PIP). ※ A thumbnail picture will be displayed when P.LIST button is pressed. In the beginning of the timer recording, it will first capture the MAIN picture, that will be used for the th...
Page 31 - Program List
07 29 On Screen Display Show the Program List. 1. Press P.LIST button to playback a recorded program. 2. Use ◀ , ▶ button to select a program. 3. Press OK button to playback the selected program. 4. If new program to be played is same as the previously played one, it will play at the position where ...
Page 33 - Playback Control
Control Playback. Choose Program List : Press P.LIST button or go to MENU and choose a ‘Program List’. Slow Motion : For slow motion press PLAY/SLOW [ ] button during normal playback mode. Press PLAY/SLOW [ ] button when returning to normal playback mode. SCAN : For scan mode, press FF [ ] button or...
Page 35 - Closed Caption; CC
33 Closed Caption On Screen Display 07 1. To turn on or off caption press CC button. 2. Every time CC button is pressed, ‘Caption On’ icon or ‘Caption Off’ icon will appear in due order. Press CC button to turn on/off closed caption.
Page 36 - Teletext; TTX; button to display current teletext.
07 34 Teletext Press ▲ , ▼ button to turn pages up and down, press number 100 to 899 to turn the direct number page. 1. Press TTX button to display current teletext. 2. Press ▲ or ▼ button to go to pages up or down. 3. Press number 100 to 899 to go to the numbered page. Available buttons during TTX ...
Page 37 - PIP Control
On Screen Display 35 PIP Control 07 Control PIP channel. ※ While recording a program, PIP window always displays the program under record. And in this case, PIP channel change and SWAP function are unavailable. ※ PIP channels can not be changed while recording using Tuner#1. ※ Radio Channel is exclu...
Page 38 - Memorize your choice of channels.; Channel Edit
Memorize your choice of channels. ※ Once Favourite channels are selected, they can be changed by pressing FAV CH +/ -- button. ※ Use OK button to make selection. ※ If you change channel in Channel Edit Menu, the timeshift and Tuner #2 recording will be automatically terminated. ※ Press MENU button t...
Page 39 - Channel Scant
37 Channel Scant Channel 08 Have an automatic channel set up. The Auto Search selects currently available channels. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Press ▲ , ▼ button to highlight ‘ Channel Scan ’. 4. The STB will automatically scan and store all of...
Page 40 - Have an manual channel set up.; Manual Scan
Have an manual channel set up. ※ After selecting the physical number/frequency, if a signal is received correctly, a message of “ LOCK ” will be displayed, otherwise “ UNLOCK ” will be displayed. ※ If you select the Manual Scan Menu, the timeshift and recording will be automatically terminated. ※ Pr...
Page 41 - Channel Sorting
39 Channel Sorting Channel 08 Select Channel Sorting Method. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Channel Sorting ’ then press OK. 4. Press ▲ , ▼ button to make a choice, then press OK. ㆍ By Logical : ‘ Channel List ’ is s...
Page 42 - Channel Duplication
Channel Duplication 08 40 Channel Select Channel Duplication Option. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Channel Duplication ’ then press OK. 4. Press ▲ , ▼ button to make a choice, then press OK. Channel Duplication func...
Page 43 - Parental Rating
41 Parental Rating Channel 08 Set Parental Guidance Rating. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK 3. Use ▲ , ▼ button to highlight ‘ Parental Rating ’ icon, then press OK. 4. Enter password to proceed. 5. Use ▲ , ▼ button to highlight ‘ Set ’ icon, then press...
Page 44 - Control HDMI video output.; HDMI Video
Control HDMI video output. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ HDMI Video ’ , then press OK. 4. Press ▲ , ▼ button to make a choice, then press OK. HDMI means the value of video timing is setup for HDMI It will take a few...
Page 45 - HDMI Audio; Control HDMI audio output.
43 HDMI Audio Audio / Video 09 Control HDMI audio output. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ HDMI Audio ’ , then press OK. 4. Press ▲ , ▼ button to make a choice, then press OK. ㆍ Auto : If the broadcaster is broadcastin...
Page 46 - Adjust display position.; Monitor Setup
Adjust display position. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Monitor Setup ’ , then press OK. 4. Customize the Monitor type to fit user ’ s TV or display. ㆍ 16 : 9 ㆍ 4 : 3 ※ Press MENU button to exit the menu screen. ※ Pr...
Page 47 - Digital Audio Out; Controls audio output type.
45 Audio / Video 09 Digital Audio Out 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Digital Audio Out. ’ , then press OK. 4. Use ▲ , ▼ button to make a choice, then press OK. ㆍ PCM : Digital Audio Output is always PCM. ㆍ Dolby D : ...
Page 48 - PIP Size
Set up the PIP size. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switch to previous step on the menu screen. 09 46 Audio / Video PIP Size 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ PIP Size ’ , then press...
Page 50 - PVR Manager; The Program List shows the recorded programs.
10 48 PVR Manager Program List The Program List shows the recorded programs. (You can also bring up the Program List by pressing the P.LIST button on the remote control.) 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Program List ’...
Page 51 - Skip Time; Set up how much time will be skipped when user press
PVR Manager 49 10 Skip Time 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Skip Time ’ , then press OK. 4. Press ▲ , ▼ button to make a choice, then press OK. ※ Press MENU button to exit the menu screen. ※ Press EXIT button to switc...
Page 52 - HDD Sleep Time
50 PVR Manager 10 HDD Sleep Time Set up how much time the HDD will be powered on after the HDD has no works to do. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ HDD Sleep Time ’ , then press OK. 4. Press ▲ , ▼ button to make a choi...
Page 53 - HDD Format; Formats the HDD. All the recorded programs will be deleted.
51 PVR Manager 10 HDD Format Formats the HDD. All the recorded programs will be deleted. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ HDD Format ’ , then press OK. 4. Enter password to proceed. 5. Press OK to start HDD format. Cau...
Page 54 - System; Opacity
52 System 11 Opacity Control opacity (transparent) of menu screen. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Opacity ’ , then press OK. 4. Press ▲ , ▼ button to make a choice, then press OK. ㆍ Opacity1 : Very Dark ㆍ Opacity2 : ...
Page 55 - Time Zone
Time Zone 53 System 11 Select time zone. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Time Zone ’ , then press OK. 4. Use ▲ , ▼ button to make a choice, then press OK. ㆍ NSW/ACT ㆍ VIC/TAS ㆍ QLD ㆍ SA ㆍ WA ㆍ NT ㆍ Auto Time Zone ※ If...
Page 56 - Daylight Saving; Select daylight saving.
54 System 11 Daylight Saving Select daylight saving. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Daylight Saving ’ , then press OK. 4. Use ▲ , ▼ button to make a choice, then press OK. ㆍ Off : Daylight Saving is off. ㆍ On : Dayli...
Page 57 - Sleep Timer
Sleep Timer 55 System 11 Select the time in which the unit is to be turned off. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ Sleep Timer ’ , then press OK. 4. Use ▲ , ▼ button to make a choice, then press OK. ※ Press MENU button t...
Page 58 - New Password
56 System 11 New Password Change the 4-digit password. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ NEW PASSWORD ’ icon, then press OK. 4. Enter password to proceed. 5. Enter new password and make a confirmation using number keys ...
Page 59 - Factory Default
Factory Default 57 System 11 Set Factory Default. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK 3. Use ▲ , ▼ button to select Factory Default, then press OK. 4. Enter password to proceed. 5. Press OK button to set to Factory Default. ※ The factory default password is...
Page 60 - About
About 58 System 11 Show the software version and date. 1. Press MENU button. 2. Use ▲ , ▼ button to highlight ‘ ’ icon, then press OK. 3. Use ▲ , ▼ button to highlight ‘ About ’ , then press OK. 4. Use ▲ , ▼ button to make a choice, then press OK. ※ Press MENU button to exit the menu screen. ※ Press...
Page 61 - Specifications; SPECIFICATIONS
59 Specifications 12 Specifications SPECIFICATIONS ITEM Antenna input 2ea & Loop Output 2ea Component (Y, Pb, Pr) Output 1set HDMI/DVI Output 1ea RGB/HV Output 1ea S-Video Output 1ea Composite Output 1ea Digital Audio Output (Optical) 1ea Digital Audio Output (Coaxial) 1ea Analog Audio Output (L...
Page 62 - NEC Service Centres; DISPLAY AND HOME GROUP
NEC Service Centres NEC Australia Pty. Ltd. ABN 86 001 217 527 DISPLAY AND HOME GROUP New South Wales Sydney 184 Milperra Rd, Revesby 2212 131-632 Newcastle 120 Parry Street, Newcastle West 2302 131-632 Victoria Melbourne Unit 1/6, Garden Road, Clayton, 3168 131-632 Queensland Brisbane Unit 4/305 Mo...