NEC NDA-24305 - Manuals - manualsarea.com

Page 3 - LIABILITY DISCLAIMER; NEAX; are registered trademarks of NEC Corporation.

LIABILITY DISCLAIMER NEC America, Inc. reserves the right to change the specifications, functions, orfeatures, at any time, without notice. NEC America, Inc. has prepared this document for use by its employees andcustomers. The information contained herein is the property of NEC America,Inc. and sha...

Page 11 - ISSUE 1; ISDN Feature Programming Manual; TABLE OF CONTENTS; Page; CHAPTER 1

NDA-24305 ISSUE 1 OCTOBER, 2000 NEAX2400 IPX ISDN Feature Programming Manual TABLE OF CONTENTS Page NDA-24305 TABLE OF CONTENTS Page i Revision 1.0 LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 12 - ELAPSED TIME DISPLAY-D

TABLE OF CONTENTS NDA-24305 Page iiRevision 1.0 TABLE OF CONTENTS (CONTINUED) Page C-97D CALL PICKUP-GROUP-D term -PRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 C-98 CALL TRANSFER-ATTENDANT-PRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 13 - CHAPTER 6

NDA-24305 TABLE OF CONTENTS Page iii Revision 1.0 TABLE OF CONTENTS (CONTINUED) Page N-22 NON-DELAY OPERATION-PRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 N-29 NIGHT CONNECTION OUTSIDE-SYSTEM-PRI . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 15 - LIST OF FIGURES; Figure

LIST OF FIGURES Figure Title Page NDA-24305 LIST OF FIGURES Page v Revision 1.0 Figure 2-1 Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 2-2 Message Sequences for Layer3 . . . . . . . . . . . . . . . . . . . . ...

Page 16 - This page is for your notes.

LIST OF FIGURES NDA-24305 Page viRevision 1.0 This page is for your notes.

Page 17 - LIST OF TABLES; Table

LIST OF TABLES Table Title Page NDA-24305 LIST OF TABLES Page vii Revision 1.0 Table 2-1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table 5-1 Gateway Service List . . . . . . . . . . . . . . . . . . . . . ....

Page 19 - HOW TO FOLLOW THE MANUAL; CONFIGURATION OF THIS MANUAL

NDA-24305 CHAPTER 1 Page 1 Revision 1.0 CHAPTER 1 INTRODUCTION 1. GENERAL The ISDN System Data Design Manual provides general information for ISDN, office data design for ISDN,and ISDN service. 2. HOW TO FOLLOW THE MANUAL 2.1 CONFIGURATION OF THIS MANUAL This manual is comprised as follows. CHAPTER ...

Page 21 - CHAPTER 2; HARDWARE CONFIGURATION; Figure 2-1 Hardware Configuration

NDA-24305 CHAPTER 2 Page 3 Revision 1.0 CHAPTER 2 GENERAL INFORMATION 1. GENERAL This chapter explains basic office data assignment procedures for ISDN and describes ISDN service features. 2. HARDWARE CONFIGURATION The system provides PRT as a primary rate ISDN interface. DTI with DCH is available a...

Page 25 - CHAPTER 3; ISDN LINE ACCESS CODE ASSIGNMENT

NDA-24305 CHAPTER 3 Page 7 Revision 1.0 CHAPTER 3 BASIC DATA ASSIGNMENT FOR ISDN 1. ISDN LINE ACCESS CODE ASSIGNMENT To initiate seizure of an outgoing trunk, one of four methods - OGC, OGCA, LCR, LCRS - can be used in thesystem. Among the four methods, however, “LCR” method alone can access an ISDN...

Page 26 - for the dummy route number.

CHAPTER 3 NDA-24305 Page 8Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN STEP 6: AFRS - Assign Number Pattern Code (NPC) and Outgoing Route Selection Pattern Number (OPR) for the dummy route number. - NPC may include ISDN trunk access code and ISDN address but not a Sub Address (SA).- OPR is a kind of ...

Page 27 - ISDN TRUNK DATA ASSIGNMENT; “SUB Address - Addressing”

NDA-24305 CHAPTER 3 Page 9 Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN 2. ISDN TRUNK DATA ASSIGNMENT STEP 1: ASYD - Assign the following indexes. SYSl Index 91: Single PLO b7 b6 b5 b4 0 1 0 1 Dual PLOs b7 b6 b5 b4 1 1 1 1 SYSl Index 186: CCIS/ISDN in service b6 b6 1 0 (When b6=1, ISDN service is inv...

Page 28 - performed after the ACSC command assignment.

CHAPTER 3 NDA-24305 Page 10Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN STEP 3: ATRK - Assign the trunk data for Bch only here. Note that the data assignment for Dch must be performed after the ACSC command assignment. - How Bch and Dch LEN appear in PIM is shown in Figure 3-1 and Figure 3-2.- As see...

Page 29 - Slot x and Slot y must be in the same HW.

NDA-24305 CHAPTER 3 Page 11 Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN Figure 3-1 ATRK for 24PRT Note 1: Slot x and Slot y must be in the same HW. Note 2: The even-numbered module group, Unit 0, Group 0 cannot be assigned as Dch LEN data. OddNumberGroup EvenNumberGroup Level Slot x Slot y LV 7 6 5 ...

Page 30 - ADPC-Assign Point Code for both Bch route and Dch route.

CHAPTER 3 NDA-24305 Page 12Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN Figure 3-2 ATRK for 24DTR + 2DCH STEP 4: ADPC-Assign Point Code for both Bch route and Dch route. - The values for a Point Code is 1 through 16383. You can assign any number as the Point Code for them, however, do not duplicate t...

Page 31 - ACSC - Assign Dch and Bch location for CSCG.

NDA-24305 CHAPTER 3 Page 13 Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN STEP 5: ACSC - Assign Dch and Bch location for CSCG. - The values for CSCG is 130 through 255.- Even number CSCGs are used for Dch location and odd number CSCGs are used for Bch location. Although Bch location is the same as Dch...

Page 33 - (3) The services to be related with this feature are shown below.; PROGRAMMING; * The detail for the pattern is programmed with the ACNDN command.

NDA-24305 CHAPTER 3 Page 15 Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN 3. CALLING NUMBER PATTERN DATA (CNP) ASSIGNMENT Calling party number can be transmitted included in the ISDN messages through ISDN network. This functionprovides the PBX user with a variety of ISDN services. This section describ...

Page 34 - Do not assign “0” at both “SKIP” and “ADD” parameter.

CHAPTER 3 NDA-24305 Page 16Revision 1.0 BASIC DATA ASSIGNMENT FOR ISDN STEP 2: ACNDN- Assign the number of digits to be added to or omitted from the calling party number datafor each Calling Number Pattern programmed in ACNPN.CNP=Calling Number Pattern assigned with ACNPN command.SKIP=the number of ...

Page 35 - CHAPTER 4; Chapter 3, “Basic Data; ASFC: Assignment of Service Feature Class Data; ARTD: Assignment of Route Class Data; Assignment of Trunk Application Data

NDA-24305 CHAPTER 4 Page 17 Revision 1.0 CHAPTER 4 COMMANDS CONCERNING ISDN DATA ASSIGNMENT 1. GENERAL This chapter explains commands concerning ISDN. Commands explained in Chapter 3, “Basic Data Assignment for ISDN” are not included in this chapter. • ASYD: Assignment of System Data Note • ASFC: As...

Page 39 - This data is valid for dummy routes.

NDA-24305 CHAPTER 4 Page 21 Revision 1.0 COMMANDS CONCERNING ISDN DATA ASSIGNMENT 2.2 ASFC: ASSIGNMENT OF SERVICE FEATURE CLASS DATA SFI 31: For SID to Terminating User-DTE0 = –1 = SID to Terminating User-DTE SFI 48: For Bearer Service0 = Speech 1 = 3.1 KHz Audio (Modem, G3 Fax) SFI 94: For SID to N...

Page 41 - This data should be set when there is no Dch in the physical DTI.

NDA-24305 CHAPTER 4 Page 23 Revision 1.0 COMMANDS CONCERNING ISDN DATA ASSIGNMENT IRL (CDN15) Clear call when DTI alarm is detected. 0 = –1 = Clear call when DTI alarm is detected Note 2 Note 2: This data should be set when there is no Dch in the physical DTI. MTC (CDN16) Assignment of Timer T309 Va...

Page 42 - Input this data by a decimal.

CHAPTER 4 NDA-24305 Page 24Revision 1.0 COMMANDS CONCERNING ISDN DATA ASSIGNMENT ANI (CDN31) Timing to demand ANI Information 0 = There is no ANI demand at Incoming call 1 = After receiving 1st digit 2 = After receiving 2nd digit 3 = After receiving 3rd digit 4 = After receiving 4th digit 5 = After ...

Page 43 - Only for Russia

NDA-24305 CHAPTER 4 Page 25 Revision 1.0 COMMANDS CONCERNING ISDN DATA ASSIGNMENT L/T (CDN35) Local/Toll Note 10 0 = Local 1 = Toll Note 10: Only for Russia ECCIS (CDN36) Event Based CCIS (E-CCIS) for the public ISDN Line 0/1 = Out of Service/In Service ECCISTM (CDN37) Release timer for E-CCIS Line ...

Page 44 - Common Use with E-CCIS RT

CHAPTER 4 NDA-24305 Page 26Revision 1.0 COMMANDS CONCERNING ISDN DATA ASSIGNMENT JECCIS (CDN48) Common Use with E-CCIS RT Note 11 0/1 = Out of Service/In Service ECCIS2 (CDN49) E-CCIS System Note 11 0 = Fixed Channel System 1 = Common Channel System 2 = Not used 3 = Not used Note 11: Valid since Ser...

Page 49 - ALTERNATE ROUTING-PRI; Chapter 3, “Basic Data Assignment for ISDN ”

NDA-24305 CHAPTER 5 Page 31 Revision 1.0 ALTERNATE ROUTING-PRI A-76 ALTERNATE ROUTING-PRI 1. General Description This feature is provided with LCR which automatically routes ISDN outgoing on-net calls over alternatefacilities when the first-choice trunk group is busy. The user selects the first-choi...

Page 50 - AUTOMATIC CALL DISTRIBUTION-PRI; Table 5-1 ACD Features

CHAPTER 5 NDA-24305 Page 32Revision 1.0 AUTOMATIC CALL DISTRIBUTION-PRI A-88 AUTOMATIC CALL DISTRIBUTION-PRI 1. General Description This feature allows Automatic Call Distribution (ACD) features to be activated for incoming calls from ISDNtrunks. Table 5-1 ACD Features CODE NO. FEATURE NAME AVAILABI...

Page 51 - Operating Procedure; Chapter 3, “Basic Data Assignment for ISDN”

NDA-24305 CHAPTER 5 Page 33 Revision 1.0 AUTOMATIC CALL DISTRIBUTION-PRI Note 1: The features indicated “Not Applicable” are features not related to trunks. Note 2: ACD features are not available for incoming data calls from ISDN trunk. Note 3: When an incoming call placed in a queue, the call is au...

Page 52 - ANNOUNCEMENT SERVICE-PRI; The system receives the announcement trunk access code.

CHAPTER 5 NDA-24305 Page 34Revision 1.0 ANNOUNCEMENT SERVICE-PRI A-92 ANNOUNCEMENT SERVICE-PRI 1. General Description This feature allows a user from the ISDN trunk to hear a prearranged announcement when the user dials apredetermined access code. Note: This feature requires an announcement machine ...

Page 53 - AUTOMATIC CIRCUIT ASSURANCE-PRI; When the station performs a switchhook flash.; When the Attendant presses “HOLD” key.; No manual operation is required.

NDA-24305 CHAPTER 5 Page 35 Revision 1.0 AUTOMATIC CIRCUIT ASSURANCE-PRI A-94 AUTOMATIC CIRCUIT ASSURANCE-PRI 1. General Description When a call connection time is less than or greater than a pre-determined time period, the system can display orprint a reference to it using this feature. Note 1: Thi...

Page 54 - AUTOMATIC TRUNK TEST-PRI; Trunk selection

CHAPTER 5 NDA-24305 Page 36Revision 1.0 AUTOMATIC TRUNK TEST-PRI A-96 AUTOMATIC TRUNK TEST-PRI 1. General Description The AUTOMATIC TRUNK TEST capability provides a functional test on a large number of ISDN trunks at aprearranged time. The results of the test are reported at the MAINTENANCE ADMINIST...

Page 55 - CHAPTER 5; General Description; Secretary must have D; for this operation. Boss may have a single line telephone.

NDA-24305 CHAPTER 5 Page 37 Revision 1.0 BOSS-SECRETARY TRANSFER-PRI B-19 BOSS-SECRETARY TRANSFER-PRI 1. General Description This service feature allows a secretary to voice-announce a call to a boss when the secretary answers a call froman ISDN trunk on the boss’ line. 2. Operating Procedure 1. Cal...

Page 59 - One burst of ringing at the forwarding station when CALL; sets, CALL FORWARDING-ALL CALLS may be assigned to a programmable

NDA-24305 CHAPTER 5 Page 41 Revision 1.0 CALL FORWARDING-ALL CALLS-PRI 3. Programming STEP 1: ASYD - System Data 1, Index 4, bit 6: One burst of ringing at the forwarding station when CALL FORWARDING-ALL CALLS is in service? 0/1: No/Yes. (single-line station only) Index 248, bit 7:Dial Tone to be se...

Page 60 - multi-line appearances on the D; Lift the handset or press the “SPEAKER” button receive Dial Tone.; OR

CHAPTER 5 NDA-24305 Page 42Revision 1.0 CALL FORWARDING-ALL CALLS-D term -PRI C-95D CALL FORWARDING-ALL CALLS-D term -PRI 1. General Description This feature permits all calls from an ISDN network destined for a particular station to be routed to anotherstation or to the Attendant, regardless of the...

Page 62 - Lift the handset or press the “SPEAKER” key receive Dial Tone.; The associated LED that is lit at another station goes out.; FWD CNCL; FORWARD CANCEL

CHAPTER 5 NDA-24305 Page 44Revision 1.0 CALL FORWARDING-ALL CALLS-D term -PRI To cancel CALL FORWARDING-ALL CALLS-D term -PRI for a multi-line appearance other than the My-line: 1. Lift the handset or press the “SPEAKER” key; receive Dial Tone. 2. Press the multi-line appearance; receive Dial Tone. ...

Page 64 - sets, CALL FORWARDING-BUSY LINE may be assigned to a programmable

CHAPTER 5 NDA-24305 Page 46Revision 1.0 CALL FORWARDING-BUSY LINE-PRI STEP 3: ASPA - Assign an access code to CALL FORWARDING-BUSY LINE Entry, SID=10 and to CALL FORWARDING-BUSY LINE Cancel, SID=11. Assign Connection Status Index(CI) for Normal service. STEP 4: ASFC - Assign the stations to receive ...

Page 65 - No limit to the number of Groups per system.

NDA-24305 CHAPTER 5 Page 47 Revision 1.0 CALL PICKUP-GROUP-PRI C-97 CALL PICKUP-GROUP-PRI 1. General Description This feature permits a station user to answer ISDN Network calls directed to other lines in a preset CALLPICKUP-GROUP simply by dialing a pickup code. 2. Operating Procedure Picking up an...

Page 66 - Picking up an incoming call:

CHAPTER 5 NDA-24305 Page 48Revision 1.0 CALL PICKUP-GROUP-D term -PRI C-97D CALL PICKUP-GROUP-D term -PRI 1. General Description This feature permits a station user to answer an ISDN network call directed to another line in a preset CALLPICKUP-GROUP by using a programmable line/feature key. CALL PIC...

Page 68 - To transfer a call in progress:

CHAPTER 5 NDA-24305 Page 50Revision 1.0 CALL TRANSFER-ALL CALLS-PRI C-99 CALL TRANSFER-ALL CALLS-PRI 1. General Description This feature permits a station user to transfer incoming or outgoing ISDN calls to another station within thesystem without Attendant assistance. 2. Operating Procedure To tran...

Page 70 - No detection

CHAPTER 5 NDA-24305 Page 52Revision 1.0 CONSULTATION HOLD-ALL CALLS-PRI C-100 CONSULTATION HOLD-ALL CALLS-PRI 1. General Description This feature permits a station user to hold any incoming or outgoing ISDN network call or any intraoffice callwhile originating a call to another station within the sy...

Page 74 - ANPD - Reserve a number level for feature access. Assign for normal.

CHAPTER 5 NDA-24305 Page 56Revision 1.0 CALL PICKUP-DIRECT-PRI C-102 CALL PICKUP-DIRECT-PRI 1. General Description This feature allows a station user to pick up an ISDN call to any other station in the system by dialing a specificcall pickup code. 2. Operating Procedure To pick-up an incoming call: ...

Page 76 - The Attendant receives Service Set Tone.

CHAPTER 5 NDA-24305 Page 58Revision 1.0 CALL PARK-PRI C-119 CALL PARK-PRI 1. General Description This feature enables the Attendant(s) or station users to “Park” calls from the ISDN network against their ownstation numbers. Calls can easily be retrieved from any station within the system. 2. Operati...

Page 77 - Assign NND in accordance with a predetermined numbering plan.; TC

NDA-24305 CHAPTER 5 Page 59 Revision 1.0 CALL PARK-PRI 3. Programming STEP 1: ASYD - System Data 1, Index 142: For CALL PARK recall, the Miscellaneous TimerCounter is assigned in bits 0-3. The Timer Class isassigned in bits 4-6. Timer Class of 3 = 2 seconds.Timer Counter of 4 = 30 seconds. (Default:...

Page 78 - This service feature requires “Digital Announcement Trunk (DAT)”; CALL FORWARDING-ALL CALLS

CHAPTER 5 NDA-24305 Page 60Revision 1.0 CALL FORWARDING-ALL CALLS-ANNOUNCEMENT-PRI C-123 CALL FORWARDING-ALL CALLS-ANNOUNCEMENT-PRI 1. General Description This feature permits all calls from ISDN trunks destined for a particular station to be routed to a recordedannouncement. Activation and cancella...

Page 79 - ANNOUNCEMENT SERVICE

NDA-24305 CHAPTER 5 Page 61 Revision 1.0 CALL FORWARDING-ALL CALLS-ANNOUNCEMENT-PRI STEP 4: ASFC - Assign the stations to activate CALL FORWARDING-ALL CALLS [C-5] a Service Feature Class that allows SFI = 7. STEP 5: AKYD - For D term sets, CALL FORWARDING-ALL CALLS [C-5] may be assigned to a program...

Page 83 - bit 0: Are the access codes for CALL FORWARDING-BUSY; sets, CALL FORWARDING-DON’T ANSWER may be assigned to a

NDA-24305 CHAPTER 5 Page 65 Revision 1.0 CALL FORWARDING-DON’T ANSWER-PRI 3. Programming STEP 1: ASYD - System Data 1, Index 5, bit 0: Are the access codes for CALL FORWARDING-BUSY LINE [C-2] and CALL FORWARDING-DON’TANSWER the same or separate? 0/1: Same/Separate. Index 69, bit 1: Send short tone w...

Page 84 - DISTINCTIVE RINGING-PRI; s will not respond to this feature.

CHAPTER 5 NDA-24305 Page 66Revision 1.0 DISTINCTIVE RINGING-PRI D-115 DISTINCTIVE RINGING-PRI 1. General Description This feature provides distinctive station ringing patterns so that the station user can distinguish between internaland external incoming calls. 2. Operating Procedure No manual opera...

Page 86 - DATA LINE SECURITY-PRI

CHAPTER 5 NDA-24305 Page 68Revision 1.0 DATA LINE SECURITY-PRI D-117 DATA LINE SECURITY-PRI 1. General Description This feature allows those line circuits used for ISDN DATA transmission to be protected from interruptions suchas ATTENDANT CAMP-ON [A-1], BUSY VERIFICATION [B-3], EXECUTIVE RIGHT OF WA...

Page 87 - DATA PRIVACY ON DEMAND-PRI; To activate DATA PRIVACY ON DEMAND-PRI from a single line:; Before beginning data communications, press the “DND” key.; ANPD - Reserve a number level for access code.

NDA-24305 CHAPTER 5 Page 69 Revision 1.0 DATA PRIVACY ON DEMAND-PRI D-118 DATA PRIVACY ON DEMAND-PRI 1. General Description This feature allows a station user to prevent interruptions to ISDN data calls by ATTENDANT CAMP-ON [A-1], BUSY VERIFICATION [B-3], CALL WAITING-TERMINATING [C-12], or ATTENDAN...

Page 89 - DATA TRANSPARENCY-PRI; No programming is required.

NDA-24305 CHAPTER 5 Page 71 Revision 1.0 DATA TRANSPARENCY-PRI D-120 DATA TRANSPARENCY-PRI 1. General Description This feature provides a completely transparent switched data path between two connected Data Terminals viaPRI. 2. Operating Procedure Establish a data call using the procedures described...

Page 90 - DATA COMMUNICATIONS-PRI; • The

CHAPTER 5 NDA-24305 Page 72Revision 1.0 DATA COMMUNICATIONS-PRI D-121 DATA COMMUNICATIONS-PRI 1. General Description This feature enables data communication between two systems, through PRI over ISDN (Digital Line Link). TheISDN link can be accessed through various connections. Note: Unrestricted Da...

Page 93 - Assign the Basic Data for ISDN. (Refer to

NDA-24305 CHAPTER 5 Page 75 Revision 1.0 DATA COMMUNICATIONS-PRI 3. Programming STEP 1: Assign the Basic Data for ISDN. (Refer to Chapter 3, “Basic Data Assignment for ISDN” .) Note: Pooled modems and modems connected to analog stations may be used on PRI channels when a straightdigital data connect...

Page 94 - DATA UNIFORM NUMBERING PLAN-PRI; Originating a Data Adapter call using uniform numbering:

CHAPTER 5 NDA-24305 Page 76Revision 1.0 DATA UNIFORM NUMBERING PLAN-PRI D-122 DATA UNIFORM NUMBERING PLAN-PRI 1. General Description This feature enables data stations to be assigned a set of UNIFORM NUMBERS to distinguish data extensionsfrom voice extensions. 2. Operating Procedure Originating a Da...

Page 97 - For Day and Night DIT service-Different Stations

NDA-24305 CHAPTER 5 Page 79 Revision 1.0 DIRECT-IN TERMINATION (DIT)-PRI For Day and Night DIT service-Different Stations STEP 7: ACSA - Assign the Route Number, Trunk Number, Connection Service Index A = 2 for DIT. Then assign the Tenant Number and Station Number to serve as the DIT station. ACSI -...

Page 98 - This feature provides an LCD display of the time elapsed while a D; is connected to a PRI trunk.

CHAPTER 5 NDA-24305 Page 80Revision 1.0 ELAPSED TIME DISPLAY-D term -PRI E-14D ELAPSED TIME DISPLAY-D term -PRI 1. General Description This feature provides an LCD display of the time elapsed while a D term is connected to a PRI trunk. 2. Operating Procedure No manual operation is required. 3. Progr...

Page 99 - FLEXIBLE NUMBERING OF STATIONS-PRI

NDA-24305 CHAPTER 5 Page 81 Revision 1.0 FLEXIBLE NUMBERING OF STATIONS-PRI F-21 FLEXIBLE NUMBERING OF STATIONS-PRI 1. General Description This feature provides the ability to assign voice station numbers and data station numbers, to any correspondinginstrument location depending solely upon numberi...

Page 100 - FAULTY TRUNK REPORT-PRI; To enter a FAULTY TRUNK REPORT:

CHAPTER 5 NDA-24305 Page 82Revision 1.0 FAULTY TRUNK REPORT-PRI F-26 FAULTY TRUNK REPORT-PRI 1. General Description This feature allows a station to report a noisy or faulty ISDN trunk number by dialing a special access codebefore hanging up. The FAULTY TRUNK REPORT consists of Trunk number, Station...

Page 101 - This feature allows the station user to respond to a VOICE CALL-D

NDA-24305 CHAPTER 5 Page 83 Revision 1.0 HANDS-FREE ANSWER BACK-D term -PRI H-14D HANDS-FREE ANSWER BACK-D term -PRI 1. General Description This feature allows the station user to respond to a VOICE CALL-D term [V-2D] without lifting the handset. 2. Operating Procedure To answer a VOICE CALL [V-2D]:...

Page 103 - Number to the sent. Include in the CD the access code of the route.

NDA-24305 CHAPTER 5 Page 85 Revision 1.0 HOT LINE-OUTSIDE-PRI STEP 4: ASPD - Assign the Tenant Number, the Abbreviated Digit Code-ADC, and the CD-Telephone Number to the sent. Include in the CD the access code of the route. STEP 5: AHLS - Assign the HOTLINE-OUTSIDE station with the following paramet...

Page 104 - INCOMING CALL IDENTIFICATION-PRI

CHAPTER 5 NDA-24305 Page 86Revision 1.0 INCOMING CALL IDENTIFICATION-PRI I-24 INCOMING CALL IDENTIFICATION-PRI 1. General Description This feature allows an ATTENDANT CONSOLE [A-3] to visually identify the type of service and/or trunkgroup which is arriving or waiting to be answered. 2. Operating Pr...

Page 105 - CAS

NDA-24305 CHAPTER 5 Page 87 Revision 1.0 INCOMING CALL IDENTIFICATION-PRI STEP 3: AAKP - This command may be used to change the meaning of the top six keys of the Call Identification keys of the Attendant Console. (See System Data 2, Indexes 8 & 9.) The Following functions may be assigned to Key...

Page 106 - INCOMING ISDN CALL TO TIE LINE CONNECTION-PRI; To Connect an Incoming Call:

CHAPTER 5 NDA-24305 Page 88Revision 1.0 INCOMING ISDN CALL TO TIE LINE CONNECTION-PRI I-25 INCOMING ISDN CALL TO TIE LINE CONNECTION-PRI 1. General Description This feature permits an Attendant to connect an incoming ISDN network call, via a tie line, to a station at adistant PBX. 2. Operating Proce...

Page 108 - INDIALING THROUGH MAIN-PRI; A 4-digit number is received via DID or NID at a main PBX.

CHAPTER 5 NDA-24305 Page 90Revision 1.0 INDIALING THROUGH MAIN-PRI I-26 INDIALING THROUGH MAIN-PRI 1. General Description With this feature a call destined for a satellite PBX via DID or Network Inward Dialing (NID) will automaticallybe routed to the satellite station by the main PBX over a tie trun...

Page 109 - ARTD - Assign Tie Line route data and the dummy route data.

NDA-24305 CHAPTER 5 Page 91 Revision 1.0 INDIALING THROUGH MAIN-PRI STEP 5: ARTD - Assign Tie Line route data and the dummy route data. For Dummy RT, CDN 6 (TCL)=4, CDN 7 (L/T)=1 and CDN 13 (AC)=1 are necessary. STEP 6: ATRK - Assign the LENS data of each trunk. STEP 7: MBTK - Make idle the trunks. ...

Page 110 - INTER-PBX COORDINATED STATION NUMBERING PLAN-PRI; All switches have a coordinated station numbering feature.

CHAPTER 5 NDA-24305 Page 92Revision 1.0 INTER-PBX COORDINATED STATION NUMBERING PLAN-PRI I-27 INTER-PBX COORDINATED STATION NUMBERING PLAN-PRI 1. General Description The INTER-PBX COORDINATED STATION NUMBERING PLAN-PRI [I-27] feature enables the Main-Satellite network to coordinate the numbering pla...

Page 111 - ISDN INDIVIDUAL CALLING LINE IDENTIFICATION (ICLID)

NDA-24305 CHAPTER 5 Page 93 Revision 1.0 ISDN INDIVIDUAL CALLING LINE IDENTIFICATION (ICLID) I-28 ISDN INDIVIDUAL CALLING LINE IDENTIFICATION (ICLID) 1. General Description The ICLID feature is used to deliver a calling-party’s number through the Public ISDN network to a called-partyin the same PBX....

Page 112 - Non-ISDN trunk to ISDN trunk; Operation at the Main location:

CHAPTER 5 NDA-24305 Page 94Revision 1.0 INTER-OFFICE OFF-HOOK QUEUING-PRI I-36 INTER-OFFICE OFF-HOOK QUEUING-PRI 1. General Description This feature can be employed in a Main-Satellite configuration to allow a satellite station user to queue forLEAST COST ROUTING-3/6-DIGIT-PRI [L-31] at the main loc...

Page 113 - bit 7: This bit must be assigned as data “0”, continuous

NDA-24305 CHAPTER 5 Page 95 Revision 1.0 INTER-OFFICE OFF-HOOK QUEUING-PRI 3. Programming STEP 1: ASYD - System Data 1, Index 42, bit 7: This bit must be assigned as data “0”, continuous Service Set Tone. STEP 2: ARTD - Assign the incoming TIE Line route. <Example of 2 - WIRE E&M/4 - WIRE E&a...

Page 115 - Senders are located on levels 4-7 of any 8RST circuit card.

NDA-24305 CHAPTER 5 Page 97 Revision 1.0 LEAST COST ROUTING-3/6-DIGIT-PRI STEP 4: ATRK - Set Originating Register Trunks (ORT) to the system in a quantity calculated from expected traffic. Registers are located on levels 0-3 of any 8RST circuit card. Senders must be assigned to the system in a quant...

Page 116 - The physical Route Number to be selected as programmed in ARTD.

CHAPTER 5 NDA-24305 Page 98Revision 1.0 LEAST COST ROUTING-3/6-DIGIT-PRI STEP 12: AFRS - List the dialing patterns in groups that will be served by a specific sequence of routes. This determination of routes is labeled as an Outgoing Pattern Route (OPR). In AFRS, programthe Tenant, Route Number (Dum...

Page 117 - Refer to

NDA-24305 CHAPTER 5 Page 99 Revision 1.0 LCR-TIME OF DAY ROUTING-PRI L-32 LCR-TIME OF DAY ROUTING-PRI 1. General Description This feature provides automatic routing of outgoing ISDN calls over alternative customer facilities based on theDDD number. The system will select the most economical route av...

Page 118 - TDPTN of the AOPR/PTN of the ATCP command.; is displayed in this service.

CHAPTER 5 NDA-24305 Page 100Revision 1.0 LCR-ATTENDANT MANUAL OVERRIDE-PRI L-33 LCR-ATTENDANT MANUAL OVERRIDE-PRI 1. General Description This service feature provides an ATTENDANT CONSOLE [A-3] to override the LCR-TIME OF DAYROUTING-PRI [L-32] pattern and then an alternate routing pattern group will...

Page 119 - Assignment Procedure

NDA-24305 CHAPTER 5 Page 101 Revision 1.0 LCR-AUTOMATIC OVERFLOW TO DDD-PRI L-34 LCR-AUTOMATIC OVERFLOW TO DDD-PRI 1. General Description This feature provides optional routing of ISDN network calls via off-network facilities from a point on thenetwork where all on-network routes are busy or none ar...

Page 121 - Dial the desired party’s number.

NDA-24305 CHAPTER 5 Page 103 Revision 1.0 LAST NUMBER CALL-PRI L-42 LAST NUMBER CALL-PRI 1. General Description When a station user originates an ISDN trunk call, this service feature allows the calling station user to recallthe same destination by dialing only the special code instead of dialing al...

Page 122 - This feature allows a D; The Prime Line lights Green.

CHAPTER 5 NDA-24305 Page 104Revision 1.0 LAST NUMBER CALLED-D term -PRI L-42D LAST NUMBER CALLED-D term -PRI 1. General Description This feature allows a D term user to redial the telephone numbers previously dialed from the terminal. With this feature, the D term user can choose any destination out...

Page 123 - FRI

NDA-24305 CHAPTER 5 Page 105 Revision 1.0 LAST NUMBER CALLED-D term -PRI 2. How to originate a call: (a) Press the LINE/SPD key on a D term . • The Prime Line lights Green. • The Speaker Lamp lights Green. • Receive Dial Tone from the speaker with the following display on the D term . (a) Repeat the...

Page 124 - LDN NIGHT CONNECTION-PRI

CHAPTER 5 NDA-24305 Page 106Revision 1.0 LDN NIGHT CONNECTION-PRI L-44 LDN NIGHT CONNECTION-PRI 1. General Description This service feature routes Listed Directory Number (LDN) calls from both ISDN/non-ISDN network to apreselected station within the system, when the Night mode has been entered. 2. O...

Page 127 - MISCELLANEOUS TRUNK ACCESS-PRI; MBTK - Assign the Make Idle status to the trunks.

NDA-24305 CHAPTER 5 Page 109 Revision 1.0 MISCELLANEOUS TRUNK ACCESS-PRI M-71 MISCELLANEOUS TRUNK ACCESS-PRI 1. General Description This feature provides access to all types of external and customer provided equipment/facilities such as Tie[T-3], and Exchange Network along with PAGING [P-1]. 2. Oper...

Page 128 - MISCELLANEOUS TRUNK RESTRICTION-PRI

CHAPTER 5 NDA-24305 Page 110Revision 1.0 MISCELLANEOUS TRUNK RESTRICTION-PRI M-72 MISCELLANEOUS TRUNK RESTRICTION-PRI 1. General Description This feature provides for incoming PRI trunks to be denied access to particular trunk groups such as Tie [T-3],Exchange Network, or PAGING [P-1]. 2. Operating ...

Page 130 - Service Conditions; Modems must be compatible.

CHAPTER 5 NDA-24305 Page 112Revision 1.0 MODEM POOLING-PRI M-74 MODEM POOLING-PRI 1. General Description The MODEM POOLING-PRI [M-74] feature allows any synchronous or synchronous data station (DTE)connected to a D term Data Adapter to have access to off-premise devices (other terminals, mainframes,...

Page 131 - Operating Procedure

NDA-24305 CHAPTER 5 Page 113 Revision 1.0 MODEM POOLING-PRI 3. Operating Procedure Refer to “[M-21] MODEM POOLING” in Feature Programming Manual. 4. Assignment Procedure Refer to “[M-21] MODEM POOLING” in Feature Programming Manual.

Page 133 - accordance with a predetermined numbering plan.; sets, MULTIPLE CALL FORWARDING-ALL CALLS may be assigned to a

NDA-24305 CHAPTER 5 Page 115 Revision 1.0 MULTIPLE CALL FORWARDING-ALL CALLS-PRI STEP 2: ANPD - Reserve a number level for feature access and cancel. Assign for Normal. Assign NND in accordance with a predetermined numbering plan. STEP 3: ASPA - Assign an access code to MULTIPLE CALL FORWARDING-ALL ...

Page 134 - Calling party hears Ringback Tone.

CHAPTER 5 NDA-24305 Page 116Revision 1.0 NIGHT CONNECTION-FIXED-PRI N-20 NIGHT CONNECTION-FIXED-PRI 1. General Description This feature routes ISDN calls normally directed to the ATTENDANT CONSOLE [A-3] to a preselectedcommon station within the system when the Night mode has been entered. 2. Operati...

Page 137 - The Attendant sets Night mode.

NDA-24305 CHAPTER 5 Page 119 Revision 1.0 NIGHT CONNECTION OUTSIDE-SYSTEM-PRI N-29 NIGHT CONNECTION OUTSIDE-SYSTEM-PRI 1. General Description This is a night transfer service on a system basis enabling a ring down call to be transferred to a preselectedstation outside the PBX via ISDN network when N...

Page 138 - NAILED DOWN CONNECTION-PRI; The Following connections are supported by this service.

CHAPTER 5 NDA-24305 Page 120Revision 1.0 NAILED DOWN CONNECTION-PRI N-31 NAILED DOWN CONNECTION-PRI 1. General Description This service feature provides the logical equivalence of a hardware connection between ISDN trunk and station/trunk. A NAILED DOWN CONNECTION is constantly maintained in the sys...

Page 139 - OUTGOING TRUNK QUEUING-PRI

NDA-24305 CHAPTER 5 Page 121 Revision 1.0 OUTGOING TRUNK QUEUING-PRI O-24 OUTGOING TRUNK QUEUING-PRI 1. General Description This feature allows a station user, upon encountering an ISDN trunk busy signal, to dial a specified access codeand enter a first-in, first-out queue. As soon as an ISDN outgoi...

Page 140 - AKYD - Set the following data to assign CALL BACK Key on a D

CHAPTER 5 NDA-24305 Page 122Revision 1.0 OUTGOING TRUNK QUEUING-PRI STEP 3: ASPA - If System Data 2, Index 4, bit 0 is assigned for separate access codes, assign an access code to OUTGOING TRUNK QUEUING assign, SRV= SSC, SID = 19 and to OUTGOING TRUNKQUEUING cancel, SRV = SSC, SID = 20. Assign SID= ...

Page 141 - Outgoing trunk

NDA-24305 CHAPTER 5 Page 123 Revision 1.0 OUTGOING TRUNK QUEUING-DELUXE-PRI O-26 OUTGOING TRUNK QUEUING-DELUXE-PRI 1. General Description This feature allows station users according to their Service Feature Class to queue for an outgoing ISDN trunkwhen all call routes are busy. This feature allows s...

Page 142 - bit 1: Automatic Setting of OG Trunk Queuing

CHAPTER 5 NDA-24305 Page 124Revision 1.0 OUTGOING TRUNK QUEUING-DELUXE-PRI 3. Programming STEP 1: ASYD - System Data 1, Index 68, bit 3: OG Trunk Queuing (On-Hook) Automatic Cancel 0/1=Out/In Service Index 159: Assign the OG-Trunk Queuing Automatic Cancel Timer,when System Data 1, Index 68, bit 3 is...

Page 143 - The caller receives Service Set Tone.

NDA-24305 CHAPTER 5 Page 125 Revision 1.0 OFF-HOOK QUEUING-PRI O-28 OFF-HOOK QUEUING-PRI 1. General Description This service allows a station user encountering busy ISDN trunk to remain off-hook and automatically enter afirst-in, first-out queue. As soon as an outgoing ISDN trunk becomes available, ...

Page 144 - Dial the access code and the desired ISDN trunk number.

CHAPTER 5 NDA-24305 Page 126Revision 1.0 OUTGOING TRUNK QUEUING-ATTENDANT-PRI O-30 OUTGOING TRUNK QUEUING-ATTENDANT-PRI 1. General Description This feature allows an ATTENDANT CONSOLE [A-3] encountering a busy ISDN trunk to remain off-hookand automatically enter a first-in, first-out queue. As soon ...

Page 147 - Refer to System Operation and Maintenance Manual.

NDA-24305 CHAPTER 5 Page 129 Revision 1.0 PEG COUNT-PRI P-37 PEG COUNT-PRI 1. General Description This feature permits traffic studies and traffic analysis information to be accessed from the MAINTENANCEADMINISTRATION TERMINAL [M-18] and to be printed out. 2. Operating Procedure Refer to System Oper...

Page 148 - PRIMARY CALL RESTRICTION-PRI

CHAPTER 5 NDA-24305 Page 130Revision 1.0 PRIMARY CALL RESTRICTION-PRI P-38 PRIMARY CALL RESTRICTION-PRI 1. General Description This feature allows the system to restrict outgoing ISDN calls according to the specific called number. Thisrestriction is controlled on the basis of the first seven, eight,...

Page 149 - PRI TRUNK TO TIE LINE CONNECTION WITH PAD CONTROL; See “Circuit Card Manual”.

NDA-24305 CHAPTER 5 Page 131 Revision 1.0 PRI TRUNK TO TIE LINE CONNECTION WITH PAD CONTROL P-39 PRI TRUNK TO TIE LINE CONNECTION WITH PAD CONTROL 1. General Description This feature provides a switchable transmission pad for PRI trunks, which allows tandem connections.Necessary PAD CONTROL is activ...

Page 150 - Station user pages the desired party.

CHAPTER 5 NDA-24305 Page 132Revision 1.0 PAGING TRANSFER-PRI P-47 PAGING TRANSFER-PRI 1. General Description This feature will allow a station user to transfer a paged call to a party that has been placed on hold. 2. Operating Procedure While a station user is engaged in a C.O. line call: 1. The Sta...

Page 151 - ARTD - Assign the paging route as shown below:

NDA-24305 CHAPTER 5 Page 133 Revision 1.0 PAGING TRANSFER-PRI STEP 2: ARTD - Assign the paging route as shown below: STEP 3: ATRK - Assign the LENs, Paging Trunk Route Number, Trunk Number, and Tenant Number. STEP 4: MBTK - Assign the Make Idle status to the Paging trunks. STEP 5: ANPD - Reserve lev...

Page 152 - PRI FAILSAFE ROUTING

CHAPTER 5 NDA-24305 Page 134Revision 1.0 PRI FAILSAFE ROUTING P-49 PRI FAILSAFE ROUTING 1. General Description When call origination via ISDN network is not available due to failure, etc., this feature allows the call to beplaced via alternative route (Public Switched Network.) 2. Operating Procedur...

Page 153 - RESTRICTION FROM OUTGOING CALLS-PRI; ROUTE RESTRICTION CLASS; 3 - Data terminal Via D

NDA-24305 CHAPTER 5 Page 135 Revision 1.0 RESTRICTION FROM OUTGOING CALLS-PRI R-35 RESTRICTION FROM OUTGOING CALLS-PRI 1. General Description This feature automatically denies preselected station lines within the system the ability to place outgoing ISDNcalls without Attendant assistance. 2. Operati...

Page 154 - The call is completed.

CHAPTER 5 NDA-24305 Page 136Revision 1.0 SPEED CALLING-SYSTEM-PRI S-82 SPEED CALLING-SYSTEM-PRI 1. General Description This feature allows a station user or ATTENDANT CONSOLE [A-3] to call frequently dialed ISDN numbersusing fewer digits (abbreviated call codes) than would normally be required. 2. O...

Page 155 - XXXX; SPD SET

NDA-24305 CHAPTER 5 Page 137 Revision 1.0 SPEED CALLING-SYSTEM-D term -PRI S-82D SPEED CALLING-SYSTEM- D term -PRI 1. General Description This feature allows a D term station user to call frequently dialed ISDN numbers using fewer digits (abbreviated call codes) than would normally be required. 2. O...

Page 156 - Number to be sent. Include the access code of the route in the CD.; key. Assign FKY 15 to the D

CHAPTER 5 NDA-24305 Page 138Revision 1.0 SPEED CALLING-SYSTEM-D term -PRI STEP 3: ASPD - Assign the Tenant Number, the Abbreviated Digit Code-ADC, and the CD-Telephone Number to be sent. Include the access code of the route in the CD. • Each abbreviated call code can store a maximum of 24 digits, in...

Page 157 - STATION MESSAGE DETAIL RECORDING SYSTEM-RS232C-PRI

NDA-24305 CHAPTER 5 Page 139 Revision 1.0 STATION MESSAGE DETAIL RECORDING SYSTEM-RS232C-PRI S-83 STATION MESSAGE DETAIL RECORDING SYSTEM-RS232C-PRI 1. General Description This feature provides a “call record” for all outgoing station-to-PRI trunk calls and incoming PRI trunk-to-station calls. When ...

Page 158 - AIOC - Assign the function and attribute data of the IOC ports.

CHAPTER 5 NDA-24305 Page 140Revision 1.0 STATION MESSAGE DETAIL RECORDING SYSTEM-RS232C-PRI System Data 1, Indexes 288-295: Designation of the attributes of the SMDR. SMDR output port will be designated. For thisdesignation, the attributes of the terminal whichoutputs the detail call information sho...

Page 159 - When Station C places a call to Station A:

NDA-24305 CHAPTER 5 Page 141 Revision 1.0 STATION MESSAGE DETAIL RECORDING SYSTEM-RS232C-PRI Figure 5-4 Example of SMDR Assignments STEP 4: ASFC - Assign data “1” to SFI14 of a Service Feature Class whose traffic is to be registered on SMDR (Trunk Basis). Assign data “1” to SFI58 of a Service Featur...

Page 162 - SIMULTANEOUS VOICE AND DATA TRANSMISSION-PRI

CHAPTER 5 NDA-24305 Page 144Revision 1.0 SIMULTANEOUS VOICE AND DATA TRANSMISSION-PRI S-86 SIMULTANEOUS VOICE AND DATA TRANSMISSION-PRI 1. General Description This feature is provided by NEC’s proprietary digital D term family of terminal equipment. A 64 kbps digital voice signal and a data signal o...

Page 165 - SYNCHRONOUS DATA SWITCHING-PRI; “SIMULTANEOUS VOICE AND DATA TRANSMISSION-PRI”

NDA-24305 CHAPTER 5 Page 147 Revision 1.0 SYNCHRONOUS DATA SWITCHING-PRI S-87 SYNCHRONOUS DATA SWITCHING-PRI 1. General Description A synchronous DTE connected to a D term /Data Adapter can communicate via the PBX with a synchronous DTE connected to a Synchronous D term /Data Adapter. 2. Operating P...

Page 166 - “STATION MESSAGE DETAIL RECORDING SYSTEM-RS232C-PRI”

CHAPTER 5 NDA-24305 Page 148Revision 1.0 SMDR FOR DATA CALL-RS232C-PRI S-88 SMDR FOR DATA CALL-RS232C-PRI 1. General Description This feature provides a call record of all outgoing station-to-trunk and incoming PRI trunk-to-station data calls.When this feature is provided, an RS232C output port is u...

Page 167 - Lift the handset (includes “SPEAKER” key operation on D; Assign the data “1” in either bit 6 or bit 7.

NDA-24305 CHAPTER 5 Page 149 Revision 1.0 SPEED CALLING OVERRIDE-SYSTEM-PRI S-89 SPEED CALLING OVERRIDE-SYSTEM-PRI 1. General Description This feature allows a station with restriction on outgoing ISDN and/or certain miscellaneous trunk calls by thestation CLASS OF SERVICE-INDIVIDUAL [C-15] to place...

Page 168 - STATION INDIVIDUAL TRUNK ACCESS-PRI; Lift the handset receive the Dial Tone

CHAPTER 5 NDA-24305 Page 150Revision 1.0 STATION INDIVIDUAL TRUNK ACCESS-PRI S-107 STATION INDIVIDUAL TRUNK ACCESS-PRI 1. General Description This feature permits a station to access an individual ISDN trunk via dial access. 2. Operating Procedure To access: 1. Lift the handset; receive the Dial Ton...

Page 169 - Lift the handset receive Dial Tone from the distant office.

NDA-24305 CHAPTER 5 Page 151 Revision 1.0 TANDEM SWITCHING OF TIE TRUNKS-2/4-WIRE-PRI T-37 TANDEM SWITCHING OF TIE TRUNKS-2/4-WIRE-PRI 1. General Description This feature allows PRI trunk-to-Tie-trunk connections through the PBX without the need for any Attendantassistance or control. The major use ...

Page 171 - XX X XX X

NDA-24305 CHAPTER 5 Page 153 Revision 1.0 THREE-WAY CALLING-PRI T-38 THREE-WAY CALLING-PRI 1. General Description This feature enables any station user to add another party to an existing ISDN network connection, establishinga Three-Way conference. 2. Operating Procedure 1. Place the original party ...

Page 172 - CNF

CHAPTER 5 NDA-24305 Page 154Revision 1.0 THREE-WAY CALLING-D term -PRI T-38D THREE-WAY CALLING-D term -PRI 1. General Description This feature enables a D term station user to establish a Three-Way conference by connecting an additional party to an already existing conversation. 2. Operating Procedu...

Page 177 - DTF3 - Display of Traffic Data 3

NDA-24305 CHAPTER 5 Page 159 Revision 1.0 UNIFORM CALL DISTRIBUTION (UCD)-PRI STEP 6: DTF3 - Display of Traffic Data 3 TYPE: Type of Traffic Measurement 8: UCD Route Peg Count 9: UCD Group Peg Count 10: UCD Station Peg Count Note: STEP 5 and STEP 6 are necessary only for measuring the UCD Traffic.

Page 182 - (1) A PBX receives INFO including SPID which was set by the terminal.

CHAPTER 6 NDA-24305 Page 164Revision 1.0 SUPPLEMENTARY SERVICE STN:TYPE: 1 (N-ISDN1) FIDP: 1-31 (FID Pattern) FUNC: 2 (Feature Identifier Data) FIDP: 1-31 (FID Pattern) 1 Transfer: Note 3 Note 1: A PBX may send EPID (Endpoint Identification), for the terminal initialization, by receiving SPID(Servic...

Page 183 - ARTD - Assign the same route data as the data for

NDA-24305 CHAPTER 6 Page 165 Revision 1.0 SUPPLEMENTARY SERVICE 3. PRI STATION (H0) STEP 1: Assign the numbering (LCR) data to access to H0 terminal. STEP 2: ARTD - Assign the same route data as the data for Chapter 3 , and arrange the following specific data to Bch and Dch route.CDN64 (NET)= 1 CDN6...

Page 184 - Circuit Card must be initialized after these assignment.

CHAPTER 6 NDA-24305 Page 166Revision 1.0 SUPPLEMENTARY SERVICE STEP 5: ACSC - Assign the location of DCH (Dch handler) and Bch. (Refer to the following example) STEP 6: ACIC1 - Assign CSCG corresponding to PC (Point Code). (Refer to the following example) PC=11 CSCG=132 STEP 7: ATRK - Assign the tru...

Page 185 - Group

NDA-24305 CHAPTER 6 Page 167 Revision 1.0 SUPPLEMENTARY SERVICE 4. PRI STATION (H11) STEP 1: Assign the numbering (LCR) data to access to H11 terminal. STEP 2: ARTD - Assign the same route data as the data for Chapter 3 , and arrange the following specific data to Bch and Dch route.CDN64 (NET)= 1CDN...

Page 186 - Assignment of Restart

CHAPTER 6 NDA-24305 Page 168Revision 1.0 SUPPLEMENTARY SERVICE STEP 4: ADPC - Assign PC (Point Code) to Bch route and Dch route. (Refer to the following example) RT=10 (Bch) PC=10 RT=11 (Bch) PC=10 RT=12 (Dch) PC=10 STEP 5: ACSC - Assign the location of DCH (Dch handler) and Bch. (Refer to the follo...

Page 187 - Bearer Capability; Chapter 3

NDA-24305 CHAPTER 6 Page 169 Revision 1.0 CALLING PARTY RECOGNITION SERVICE (CALL FORWARDING-ALL CALLS/BUSY LINE/DON’T ANSWER) C-103 CALLING PARTY RECOGNITION SERVICE (CALL FORWARDING-ALL CALLS/BUSY LINE/DON’T ANSWER) 1. General Description This feature enables the PBX to transfer a direct incoming ...

Page 189 - ASFC - Enter Service Feature Restriction Data

NDA-24305 CHAPTER 6 Page 171 Revision 1.0 CALLING PARTY RECOGNITION SERVICE (CALL FORWARDING-ALL CALLS/BUSY LINE/DON’T ANSWER) STEP 8: ASFC - Enter Service Feature Restriction Data SFI: Service Feature Index (1~127)7-CALL FORWARDING ALL CALLS8-CALL FORWARDING DON’T ANSWER9-CALL FORWARDING BUSY LINE ...

Page 190 - and ISDN terminal

CHAPTER 6 NDA-24305 Page 172Revision 1.0 CALLING PARTY RECOGNITION SERVICE [DIRECT-IN TERMINATION (DIT) ] C-104 CALLING PARTY RECOGNITION SERVICE [DIRECT-IN TERMINATION (DIT) ] 1. General Description An Incoming Call from the ISDN network can be connected to the specific station, which can be assign...

Page 191 - TENANT NUMBER

NDA-24305 CHAPTER 6 Page 173 Revision 1.0 CALLING PARTY RECOGNITION SERVICE [DIRECT-IN TERMINATION (DIT) ] STEP 6: AFCP - Assign the transfer destination. (For more information, see Figure 6-1 .) DAY/NIGHT: Day mode/Night mode TN: TENANT NUMBER CALLING PARTY: (Max. 32 digits) Called Station Number (...

Page 192 - COC Number

CHAPTER 6 NDA-24305 Page 174Revision 1.0 CALLING PARTY RECOGNITION SERVICE [DIRECT-IN TERMINATION (DIT) ] Example: AFCP DAY/NIGHT: D TN: 1 CALLING PARTY 2222 + ACC 0471272991CFSI: 3 CFD: 0 STN: 3501 Figure 6-1 Assigning Transfer Destination COC Number SID PBX ICT 3500 I S DN Calling Subscriber: 0471...

Page 194 - DID ADDRESSING

CHAPTER 6 NDA-24305 Page 176Revision 1.0 DID ADDRESSING D-123 DID ADDRESSING 1. General Description This feature provides for a called-party number received via ISDN to be used to designate the station at whichthe call is to terminate. 2. Operating Procedure No manual operation is required. 3. Progr...

Page 195 - Assign the Basic Data for ISDN (Refer to

NDA-24305 CHAPTER 6 Page 177 Revision 1.0 DID ADDRESSING STEP 1: Assign the Basic Data for ISDN (Refer to Chapter 3 .) STEP 2: ARTD - Assign the number of digits to be decoded in the System to the parameter DC (CDN=66) of the Route of the B-channels and D-channel of a 24PRT which interfaces with the...

Page 196 - information on the D; or PS terminal in the system

CHAPTER 6 NDA-24305 Page 178Revision 1.0 NETWORK NAME DISPLAY (NI-2 PRI) N-47 NETWORK NAME DISPLAY (NI-2 PRI) 1. General Description This feature provides the Name Display service between NEAX2400 IPX system and National-ISDN 2 network(NI-2 network or NI-2). Note: Name Display service supports the f...

Page 197 - Service Conditions; “Programming”

NDA-24305 CHAPTER 6 Page 179 Revision 1.0 NETWORK NAME DISPLAY (NI-2 PRI) 3. Service Conditions 1. This feature is available since Series 7400 Release 9 software. 2. This feature is available on condition that the system data is assigned to allow OAI service (seePROGRAMMING). 3. This feature is not ...

Page 198 - SID TO TERMINATING USER - DISPLAY

CHAPTER 6 NDA-24305 Page 180Revision 1.0 SID TO TERMINATING USER - DISPLAY S-93 SID TO TERMINATING USER - DISPLAY 1. General Description This ISDN feature provides a visual display of the calling station’s number and sub address information on aD term for incoming ISDN calls. This provides the termi...

Page 199 - shows it

NDA-24305 CHAPTER 6 Page 181 Revision 1.0 SID TO TERMINATING USER (CALL-BY-CALL) - DISPLAY FOR AT&T (#4ESS) S-136 SID TO TERMINATING USER (CALL-BY-CALL) - DISPLAY FOR AT&T (#4ESS) 1. General Description This feature allows a PBX to request either ANI or SID for each incoming call (Call-by-Ca...

Page 200 - SID TO TERMINATING USER - DTE; This ISDN feature permits a DTE connected to terminating D; via a data adapter to receive the originating

CHAPTER 6 NDA-24305 Page 182Revision 1.0 SID TO TERMINATING USER - DTE S-94 SID TO TERMINATING USER - DTE 1. General Description This ISDN feature permits a DTE connected to terminating D term via a data adapter to receive the originating station number sent from the ISDN network. 2. Operating Proce...

Page 201 - SUB ADDRESS - ADDRESSING; automatically presented on the display of the D

NDA-24305 CHAPTER 6 Page 183 Revision 1.0 SUB ADDRESS - ADDRESSING S-95 SUB ADDRESS - ADDRESSING 1. General Description This ISDN feature permits an incoming call to be directed to a designated station by using called-party sub-address information. 2. Operating Procedure No manual operation is requi...

Page 203 - B-CHANNEL SERVICE CONTROL; A PBX sends a trunk maintenance message.

NDA-24305 CHAPTER 6 Page 185 Revision 1.0 B-CHANNEL SERVICE CONTROL B-27 B-CHANNEL SERVICE CONTROL 1. General Description A PBX can send a trunk maintenance (SERVICE) message to the ISDN (AT&T-#4ESS, NT-DMS100/250)when setting or cancelling a trunk make busy using the MBTK command. This function...

Page 204 - Channel selection is possible by the LCR function only.

CHAPTER 6 NDA-24305 Page 186Revision 1.0 CALL-BY-CALL POOL MANAGEMENT C-106 CALL-BY-CALL POOL MANAGEMENT 1. General Description A single PRI interface can be used in common by TRUNK PROVISIONING [T-42] and CALL-BY-CALLSERVICE SELECTION [C-105]. If all the channels that are used by TRUNK PROVISIONING...

Page 207 - Originating RT number

NDA-24305 CHAPTER 6 Page 189 Revision 1.0 CCIS TANDEM CALL-CALLING PARTY NUMBER (CPN) DELIVERY TO ISDN & Q-SIG NETWORKS 4. Programming 1. When programmed at non-fusion PBX (stand-alone system): STEP: ACPNCL - OGRT: Originating RT number RCPN: Calling party number changed by this service (1~24 di...

Page 208 - When programmed at fusion node:

CHAPTER 6 NDA-24305 Page 190Revision 1.0 CCIS TANDEM CALL-CALLING PAR TY NUMBER (CPN) DELIVERY TO ISDN & Q-SIG NETWORKS 2. When programmed at fusion node: STEP : ACPNCN - OGLGRT: Originating RT number (Logical RT number)RCPN: Calling party number changed by this service (1~24 digits.)* Not neces...

Page 209 - By the command CDBU of MAT.

NDA-24305 CHAPTER 6 Page 191 Revision 1.0 D-CHANNEL BACKUP - PRI D-152 D-CHANNEL BACKUP - PRI 1. General Description D-channel Backup feature is available in Non-Facility Associated Signaling (for AT&T/NT/N-ISDN2). • Changeover to Backup D-channel automatically executes when a link of ACT D-chan...

Page 210 - Backup Dch is Located on PRT

CHAPTER 6 NDA-24305 Page 192Revision 1.0 D-CHANNEL BACKUP - PRI STEP 3: ATRK - Assign the trunk data of Bch. (Refer to “ Chapter 3 ”) <For example> RT=20 TK1-TK70 (Bch) STEP 4: ADPC - Assign PC (Point Code) to Bch route and Dch route. <For example> RT=20 (Bch) PC=20 RT=21 (Dch) PC=20 STE...

Page 212 - MEGACOM ACCESS

CHAPTER 6 NDA-24305 Page 194Revision 1.0 MEGACOM ACCESS M-76 MEGACOM ACCESS 1. General Description AT&T’s MEGACOM (WATS) network can be used. Note 1: The available WATS service is limited to MSB (Maximal Subscribed WATS Band). Note 2: The parameter band service where zone is specified on a call-...

Page 216 - Each B-channel uses the Individual Route Number.

CHAPTER 6 NDA-24305 Page 198Revision 1.0 NON-FACILITY ASSOCIATED SIGNALING - PRI 2. Each B-channel uses the Individual Route Number. STEP 1: Assign the numbering (LCR) data to access to ISDN. STEP 2: ARTD - Assign the route data. (Refer to “ Chapter 3 ”) STEP 3: ATRK - Assign the trunk data of Bch. ...

Page 218 - Q-SIG/ISDN INTERNATIONAL GATEWAY SWITCHING; When μ-law is selected as output Layer 1 protocol to outgoing trunk.

CHAPTER 6 NDA-24305 Page 200Revision 1.0 Q-SIG/ISDN INTERNATIONAL GATEWAY SWITCHING Q-5 Q-SIG/ISDN INTERNATIONAL GATEWAY SWITCHING 1. General Description This feature allows converting a User Information Layer 1 Protocol (µ-law/A-law) of call originated to ISDNline according to the office data. See ...

Page 219 - This feature is available since Series 7400 Release 9 software.

NDA-24305 CHAPTER 6 Page 201 Revision 1.0 Q-SIG/ISDN INTERNATIONAL GATEWAY SWITCHING 2. Operating Procedure No manual operation is required. 3. Service Conditions 1. This feature is available since Series 7400 Release 9 software. 2. This feature is available for a call to ISDN line (This feature doe...

Page 220 - This feature is activated when SETUP message is sent.; Table 5-1 Reference: Output Layer 1 Protocol

CHAPTER 6 NDA-24305 Page 202Revision 1.0 Q-SIG/ISDN INTERNATIONAL GATEWAY SWITCHING 4. When the protocol is selected as AUSTRALIA in the route class data (assigned in ARTD, CDN65: INT)and the coding standard is “00” in BC information element, call in A-law only can be connected (call in µ-law is dis...

Page 221 - under

NDA-24305 CHAPTER 6 Page 203 Revision 1.0 Q-SIG/ISDN INTERNATIONAL GATEWAY SWITCHING 4. Interactions This feature is applied for H0/H11 terminal when the service conditions described in Item 3 under Service Conditions are satisfied. 5. Programming STEP 1: ARTI - Assign the Trunk Application data to ...

Page 222 - SDN ACCESS

CHAPTER 6 NDA-24305 Page 204Revision 1.0 SDN ACCESS S-90 SDN ACCESS 1. General Description AT&T’s SDN (Software Defined Network) can be used. Note 1: When a call has terminated by the CALL-BY-CALL SERVICE SELECTION [C-105], no indication todistinguish it from a call termination by other services...

Page 223 - Lift the handset and receive Dial Tone.

NDA-24305 CHAPTER 6 Page 205 Revision 1.0 SID TO NETWORK - PRESENT/SID TO NETWORK - PRIVACY S-91/S-92 SID TO NETWORK - PRESENT/SID TO NETWORK - PRIVACY 1. General Description <SID TO NETWORK-PRESENT>This feature allows SID (Station Identification Number) to be delivered to the ISDN when a call...

Page 224 - Assign “Authorization Code” data.

CHAPTER 6 NDA-24305 Page 206Revision 1.0 SID TO NETWORK - PRESENT/SID TO NETWORK - PRIVACY . <For SID TO NETWORK-PRIVACY> STEP 4: ASFC - Allow SID to Network-Privacy (SFI 94) to the SFC of the station. SFI94=0/1=-/SID is not transfer to a destination. Note: This data is necessary for the tempo...

Page 225 - SUB ADDRESS - PRESENT

NDA-24305 CHAPTER 6 Page 207 Revision 1.0 SUB ADDRESS - PRESENT S-96 SUB ADDRESS - PRESENT 1. General Description This ISDN feature allows a PRIMARY RATE INTERFACE ISDN trunk to transfer the called-party sub-addressinformation to a destination ISDN station when the call is originated via the PBX. Th...

Page 226 - TRUNK PROVISIONING SERVICE SELECTION

CHAPTER 6 NDA-24305 Page 208Revision 1.0 TRUNK PROVISIONING SERVICE SELECTION T-42 TRUNK PROVISIONING SERVICE SELECTION 1. General Description Each channel of a PRI interface can be dedicated to a particular service. Services are designated to specificchannels; once designated, a channel can only be...

Page 228 - No manual is operation required.

CHAPTER 6 NDA-24305 Page 210Revision 1.0 CALLING PARTY INFORMATION TRANSFER/TRANSFER MESSAGE (TRM) C-112/T-44 CALLING PARTY INFORMATION TRANSFER/TRANSFER MESSAGE (TRM) 1. General Description <CALLING PARTY INFORMATION TRANSFER>When attribute data (BC, LLC, HLC) arrives from the ISDN or an ISDN...

Page 231 - The following issues of firmwares are required.

NDA-24305 CHAPTER 6 Page 213 Revision 1.0 NATIONAL - ISDN2 - PRI N-42 NATIONAL - ISDN2 - PRI 1. General Description This feature allows the system to connect with N-ISDN2 network. NON-FACILITY ASSOCIATEDSIGNALING and D-CHANNEL BACKUP are also available. Note 1: Network-side services, VIRTUAL TIE LIN...

Page 232 - VIRTUAL TIE LINE

CHAPTER 6 NDA-24305 Page 214Revision 1.0 VIRTUAL TIE LINE V-18 VIRTUAL TIE LINE 1. General Description This service feature provides the virtual tie line service by setting up a connection between a PBX and anothervia ISDN network during the designated period of time. While the virtual tie line is s...

Page 233 - Service Status

NDA-24305 CHAPTER 6 Page 215 Revision 1.0 VIRTUAL TIE LINE • Service Status Note: When a call is connected to the Virtual Tie Line at the time designated to cancel the connection, theconnection is extended by 10 minutes (maximum 30 minutes) to wait for the call to be released. After30 minutes, the c...

Page 234 - Setup/Cancel Protocol for Virtual Tie Line

CHAPTER 6 NDA-24305 Page 216Revision 1.0 VIRTUAL TIE LINE • Setup/Cancel Protocol for Virtual Tie Line 2. Operating Procedure No manual operation is required. PBX Setup SETUP(B) CALL PRO C PBX ISDN CONN ACK IAI CLF CONN ACM DISC REL COMP REL DISC REL COMP REL SETUP(B) CONN ACK CONN AND RLG Talk/Comm...

Page 235 - Dch

NDA-24305 CHAPTER 6 Page 217 Revision 1.0 VIRTUAL TIE LINE 3. Programming STEP 1: Assign the Basic Data for ISDN. (Refer to Chapter 3 .) Note 1: If in Virtual Tie Line network, an alternative route cannot be assigned. Note 2: Example for ports allocation of the command ATRK. STEP 2: Assign the data ...

Page 237 - EVENT BASED CCIS - ISDN TRANSPORT; The ISDN Primary Rate Interface (PRI) trunk is used for this feature.

NDA-24305 CHAPTER 6 Page 219 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT E-23 EVENT BASED CCIS - ISDN TRANSPORT 1. General Description This feature provides VIRTUAL TIE LINE for each event such as call origination and MCI messagetransmission. Inter-PBX link for this feature is established on B-ch...

Page 238 - The following features are available for the E-CCIS line:; Dual Hold D; Hands-Free Answerback – D

CHAPTER 6 NDA-24305 Page 220Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT 8. The following features are available for the E-CCIS line: • Asynchronous Data Switching [A-44] Note • Attendant Camp-On with Tone Indication – CCIS [A-45] • Attendant-Controlled Conference – CCIS [A-46] • Automatic Recall ...

Page 239 - Message Reminder – D; Service Display – D

NDA-24305 CHAPTER 6 Page 221 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT • Hotline – CCIS [H-12] • Incoming Call Identification – CCIS [I-16] • Individual Attendant Access – CCIS [I-17] • Inter-Position Transfer – CCIS [I-18] • Individual Trunk Access – CCIS [I-19] • Look Ahead Routing – CCIS [L-...

Page 241 - Example of ports allocation by ATRK command is shown below.

NDA-24305 CHAPTER 6 Page 223 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT Note: Example of ports allocation by ATRK command is shown below. STEP 2: Assign CCIS No. 7 related data. STEP 3: ARTD - Assign Bearer Capability for the speech channels of the E-CCIS line. CDN:45 A/D: 0/1 = Analog (Bearer C...

Page 245 - STN: 3500 (DID Number or Converted Number generated by ACDD command)

NDA-24305 CHAPTER 6 Page 227 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT STEP 3: AEVT - RT20 TK1 DESTINATION: 9800 (E-CCIS trunk identification number)CALLING: 0471813500 (DID number for incoming call)CALLED: 0891245600 (DID number for outgoing call)C_RT: 120 (CCIS Signal Route Number)C_TK: 1 (CC...

Page 247 - E-CCIS Signal Channel

NDA-24305 CHAPTER 6 Page 229 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT • Example of port allocation when using DID Number as addressing information Data assignment procedure related to the E-CCIS line is shown below. STEP 10: ARTD - RT20 CDN 45 (A/D): 0 CDN 66 (DC): 4 RT120 CDN 66 (DC): 4 STEP ...

Page 248 - DID Number or Converted Number generated by ACDD command

CHAPTER 6 NDA-24305 Page 230Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT STEP 12: AEVT - RT20 TK1 DESTINATION: 3500 (E-CCIS trunk identification number)CALLING: 0471813500 (DID number for incoming call)CALLED: 0891245600 (DID number for outgoing call)C_RT: 120 (CCIS Signal Route Number)C_TK: 1 (CC...

Page 250 - Billing information

CHAPTER 6 NDA-24305 Page 232Revision 1.0 EVENT BASED CCIS - Q-SIG TRANSPORT 9. Billing information (a) OG billing and IC billing data should be set for each route via the ARTI command. (b) Trunk identification number assigned at DESTINATION of the AEVT command is output to the SDMR text in place of ...

Page 251 - Do Not Disturb – D

NDA-24305 CHAPTER 6 Page 233 Revision 1.0 EVENT BASED CCIS - Q-SIG TRANSPORT • Digital Display – Trunk – CCIS [D-73] • Direct-In Termination – CCIS [D-74] • Distinctive Ringing – CCIS [D-75] • Do Not Disturb – D term – CCIS [D-76D] • Data Hotline – CCIS [D-86] Note • Dialed Number Display – Recall –...

Page 254 - DID Number for incoming calls from an E-CCIS line:

CHAPTER 6 NDA-24305 Page 236Revision 1.0 EVENT BASED CCIS - Q-SIG TRANSPORT Examples of Data Assignment for the E-CCIS line • Example of port allocation when using Called Sub Address as addressing information Data assignment procedure related to the E-CCIS line is shown below.E-CCIS speech line for ...

Page 256 - For Office A] DID Number for incoming calls from an E-CCIS line:

CHAPTER 6 NDA-24305 Page 238Revision 1.0 EVENT BASED CCIS - Q-SIG TRANSPORT • Example of port allocation when using DID Number as addressing information Data assignment procedure related to the E-CCIS line is shown below.E-CCIS speech line for the office A (PC=2) → RT20 E-CCIS speech line for the of...

Page 261 - The conditions of alternate routing are as follows.

NDA-24305 CHAPTER 6 Page 243 Revision 1.0 CALL COMPLETION ON NO REPLY (CCNR) 19. The conditions of alternate routing are as follows. (a) If the data link fault occurs when the station is operating to set CCNR, the message for service set is sent using alternate route providing that the interface is ...

Page 262 - recalls the calling party.; CCNR is set from Station A.; LEGEND

CHAPTER 6 NDA-24305 Page 244Revision 1.0 CALL COMPLETION ON NO REPLY (CCNR) (b) When Call Forwarding - All Calls/Busy Line/Don’t Answer is set on a calling station, the system recalls the calling party. (c) When a called station is set Call Forwarding - All Calls/Busy Line/Don’t Answer after CCBS se...

Page 264 - Station A and Station B are in station-to-station connection.

CHAPTER 6 NDA-24305 Page 246Revision 1.0 CALL COMPLETION TO BUSY SUBSCRIBER (CCBS) C-148 CALL COMPLETION TO BUSY SUBSCRIBER (CCBS) 1. General Description This feature allows an Inter-Office Call Back when the calling station and the called station respectively belongto a different PBX in a Q-SIG net...

Page 265 - Station C answers and receives Ring Back Tone Station B rings.

NDA-24305 CHAPTER 6 Page 247 Revision 1.0 CALL COMPLETION TO BUSY SUBSCRIBER (CCBS) 4. Station C dials the access code for CCBS; Station C receives Service Set Tone and hangs up. 5. Both Stations A and B hang up (i.e. Station B becomes idle); Station C rings. 6. Station C answers and receives Ring B...

Page 271 - STEP 1: ARTD - Assign the following CDN data for the B channel route.

NDA-24305 CHAPTER 6 Page 253 Revision 1.0 CALL COMPLETION TO BUSY SUBSCRIBER (CCBS) STEP 1: ARTD - Assign the following CDN data for the B channel route. CDN43(BT): 1 STEP 2: ASYD - System Data 1, Index 68, bit 0. Operating method for busy station service. 0/1 = SHF + Access Code/Last Digit + Access...

Page 272 - This service is not available when:

CHAPTER 6 NDA-24305 Page 254Revision 1.0 CNIP/CONP C-153 CNIP/CONP 1. General Description In between Q-SIG networks, this feature allows calling or called party's information, called Name ID, to bedisplayed on the D term LCD. This feature conforms to ETS 300 238. This feature is available for IS-115...

Page 275 - The functions of this feature are as follows.

NDA-24305 CHAPTER 6 Page 257 Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING C-158 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING 1. General Description This feature provides Call Forwarding service activated to be followed by IS-13873/ETS 300 257 protocol(SS-...

Page 276 - Calling Party

CHAPTER 6 NDA-24305 Page 258Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING 3. Rerouting FunctionTo select the most proper routing (prevent to keep holding the unnecessary line), the line from the callingparty to the forwarded destination is newly established when SS-CF ser...

Page 279 - C is set a call to forward to Station B.; or analog station. (When one of those stations is ISDN terminal,

NDA-24305 CHAPTER 6 Page 261 Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING Example 1) Station A originates a call to Station B, and Station B set to forward a call to Station C. Station C is set a call to forward to Station B. The call is terminated at the Station B after...

Page 280 - “83”). Rerouted line connection is Office “80”

CHAPTER 6 NDA-24305 Page 262Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING 2. Rerouting function is also available for the call in the example below. 3. When interworking through FCCS link, rerouting function is activated with no restriction. 4. When station-to-station con...

Page 283 - Call Forwarding-Supplementary Service

NDA-24305 CHAPTER 6 Page 265 Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING 4. Interactions Call Forwarding-Supplementary Service 1. When CALL COMPLETION ON NO REPLY (CCNR) is used with this feature that conforms to Q-SIG: Note: CCNR available for the Q-SIG network. SS-CFU...

Page 284 - This feature requires 24DTI circuit card.

CHAPTER 6 NDA-24305 Page 266Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING 7. When the OFF HOOK QUEUEING [O-7] service is used with this feature;SS-CFNR: When the call is forwarded to the trunk by SS-CFNR and the destination trunk is busy, OFF HOOK QUEUEING is not availabl...

Page 285 - SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) ”

NDA-24305 CHAPTER 6 Page 267 Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING 5. Programming First, assign the data for IS-11572/Q-SIG interface establishment referring to “IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) ” / “Q-SIG (CIRCUIT SWITCHED BASIC ...

Page 286 - STEP 4: ASYD - Assign the system data concerned with the service.

CHAPTER 6 NDA-24305 Page 268Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING STEP 8: ARTI - Assign the trunk application data. CDN52 : CTCF - 1 = SS-CT/SS-CF service is effective.CDN53 : RERT - 1 = Rerouting function is effective. • SS-CFB STEP 1: ASFC - Assign the service f...

Page 287 - STEP 5: ASYD - Assign the system data concerned with the service.

NDA-24305 CHAPTER 6 Page 269 Revision 1.0 CALL FORWARDING SUPPLEMENTARY SERVICE (SS-CF) WITH REROUTING • SS-CFNR STEP 1: ASFC - Assign the service feature class. SFI=8 (Call Forwarding - Don’t Answer)RES=1(Available) STEP 2: ATNR - Allow the tenant connection between the station and the station and/...

Page 289 - Series III) and LCD display on Station C is “3001”.

NDA-24305 CHAPTER 6 Page 271 Revision 1.0 CALL TRANSFER SUPPLEMENTARY SERVICE (SS-CT) WITH REROUTING 2. Rerouting FunctionTo prevent keeping a hold on the unnecessary line, the line from the calling party to the forwardeddestination is newly established when SS-CT service is successful. LCDs of stat...

Page 291 - Rerouting Function; ) Station A originates a call to Station B through Office “81”.

NDA-24305 CHAPTER 6 Page 273 Revision 1.0 CALL TRANSFER SUPPLEMENTARY SERVICE (SS-CT) WITH REROUTING Rerouting Function 1. Rerouting function is available when: (a) SS-CT service is available. (b) Bearer Capability information of speech or 3.1 kHz audio is available for rerouting function (Unrestric...

Page 293 - Call Transfer-Supplementary Service

NDA-24305 CHAPTER 6 Page 275 Revision 1.0 CALL TRANSFER SUPPLEMENTARY SERVICE (SS-CT) WITH REROUTING 4. Interactions Call Transfer-Supplementary Service 1. When CALL PARK [C-29] is used with this feature:The call parked by CALL PARK feature cannot be transferred by the SS-CT service. While, the stat...

Page 294 - STEP 1: ASYD - Assign the system data concerned with this feature.

CHAPTER 6 NDA-24305 Page 276Revision 1.0 CALL TRANSFER SUPPLEMENTARY SERVICE (SS-CT) WITH REROUTING 5. Programming Assign the data for IS-11572/Q-SIG interface establishment referring to “IS-11572 (Layer 3 specifications forinter-PBX signaling protocol)/Q-SIG (Circuit Switched Basic Call-ETSI Versio...

Page 295 - Outgoing/Incoming Call Connection

NDA-24305 CHAPTER 6 Page 277 Revision 1.0 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) I-42 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) 1. General Description This feature allows inter-PBX link using Layer 3 signalling protocol supporting circuit mode bea...

Page 297 - Connectivity

NDA-24305 CHAPTER 6 Page 279 Revision 1.0 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) 3. Connectivity IS-11572 is available for the following connection and interworking with the other networks.Note that connection test is required when the NEC’s PBX and other manufacturer’s P...

Page 298 - CONNECTIVITY; TYPE OF NETWORK

CHAPTER 6 NDA-24305 Page 280Revision 1.0 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) • Connectivity between IS-11572 and terminal equipment is shown below. 4. Calling/Called Party Number Information • As a calling/called party number, a maximum of 32 digits can be transmitted ...

Page 300 - Pattern 1: The ISDN tandem connection

CHAPTER 6 NDA-24305 Page 282Revision 1.0 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) (c) The connection patterns for the UUS transmission are shown in the figure below. Pattern 1: The ISDN tandem connection Note: Either ISDN(a) or ISDN(b) is Q-sig/IS-11572 interface. PBX PBX P...

Page 301 - STEP 2: Assign the numbering plan data for call origination.; CDN

NDA-24305 CHAPTER 6 Page 283 Revision 1.0 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) 4. Programming STEP 1: ASYD - Assign the following data. SYS-1 Index 186 bit6=1 (ISDN/CCIS is in service)187=00 Hex220 bit6=0 (ISDN is in service) STEP 2: Assign the numbering plan data for c...

Page 302 - ACIC2 command assignment.; PR

CHAPTER 6 NDA-24305 Page 284Revision 1.0 IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX SIGNALING PROTOCOL) STEP 4: ARTI - Assign the trunk application data. INTD = 1 (IS-11572) STEP 5: ATRK - Assign Bch trunks. Note that the LEN of Dch trunk should be assigned after STEP 9: ACIC2 command assignment...

Page 304 - PBX to PBX

CHAPTER 6 NDA-24305 Page 286Revision 1.0 Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION) 1. Q reference pointThe Q reference point is not expected to be a physical interface but is shown in conceptual terms in the figurebelow.The Q-Sig protocol creates Layer 3 messages for inter-PTN (PBX) signali...

Page 306 - Example of Message Sequences

CHAPTER 6 NDA-24305 Page 288Revision 1.0 Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION) 4. Example of Message Sequences <Enbloc Sending/Call Clearing> OG PBX IC PBX SETUP CONN ACK DISC REL COM Call Active CALL PROC ALERT CONN REL <Overlap Sending/Call Clearing> OG PBX IC PBX SETUP AC...

Page 307 - None

NDA-24305 CHAPTER 6 Page 289 Revision 1.0 Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION) 5. Transparency Note 1: When there is no called party number from ISDN, PBX may define the called party number. Note 2: In the connection from Q-SIG to ISDN, PBX may add or delete digits of the called party ...

Page 309 - (c) The connection patterns for the UUS transmission are shown in; Figure 6-1 Connection Patterns for UUS Transmission

NDA-24305 CHAPTER 6 Page 291 Revision 1.0 Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION) (c) The connection patterns for the UUS transmission are shown in Figure 6-1 . Figure 6-1 Connection Patterns for UUS Transmission Pattern 1: The ISDN tandem connection Note: Either ISDN(a) or ISDN(b) is Q-S...

Page 310 - STEP 2: Assign the numbering plan data for the originating call.

CHAPTER 6 NDA-24305 Page 292Revision 1.0 Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION) 4. Programming STEP 1: ASYD - Assign the following data. SYS-1 Index 186 bit6=1 (ISDN/CCIS is in service)187=00 Hex220 bit6=0 (ISDN is in service) STEP 2: Assign the numbering plan data for the originating ca...

Page 311 - Assign “1” when the number display on LCD of terminal is required.; Attention: The circuit card; must; be initialized after changing data.

NDA-24305 CHAPTER 6 Page 293 Revision 1.0 Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION) Note 3: Assign “1” when the number display on LCD of terminal is required. Note 4: Assign “1” when the User-to-User Signaling notification is required. Note 5: Assign “1” when the multi-rate bearer service i...

Page 312 - NETWORK; This feature is available since Series 7400 (Release 8) software.; AOC-E: Charging information at the end of the call

CHAPTER 6 NDA-24305 Page 294Revision 1.0 ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK A-136 ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK 1. General Description This feature provides the calling station originated a call to ISDN ...

Page 314 - Example of Message Sequence; Station A calls to Station B and the two stations are connected.

CHAPTER 6 NDA-24305 Page 296Revision 1.0 ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK 5. Example of Message Sequence Some examples of message sequence for this service are shown below. Station A calls to Station B and the two stations are connected. ETSI/ IS-11572...

Page 315 - or

NDA-24305 CHAPTER 6 Page 297 Revision 1.0 ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK 6. Programming STEP 1: Assign the data for establishing Q-SIG/IS-11572 line followed by “Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION)” or “IS-11572 (LAYER 3 SPECIFICATIONS...