NEC NDA-24233 - Manuals
NEC NDA-24233 – Manual in PDF format online.
Manuals:
Manual NEC NDA-24233
Summary
LIABILITY DISCLAIMER NEC America, Inc. reserves the right to change the specifications,functions, or features, at any time, without notice. NEC America, Inc. has prepared this document for use by its em-ployees and customers. The information contained herein is theproperty of NEC America, Inc. and s...
EXHIBIT J1 FCC REQUIREMENTS NEC America, Inc. VisuaLink 128/VisuaLink 384 TYPE OF SERVICE The VisuaLink 128 and the VisuaLink 384 are stand-alone devices that allow multimedia conferencing by transmitting video, audio and data to remote locations over the ISDN Basic Rate interface. The VisuaLink 128...
IF PROBLEMS ARISE If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone lines, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will not...
CSA Requirement To ensure that certified equipment is attached correctly, and only to the networks of participating carriers, the following statement shall accompany each unit of certified equipment offered for sale. This statement must be included conspicuously in written or electronic format, at o...
NDA-24233 Issue 2 Page i VisuaLink 128/384 Engineering Guide Table of Contents Table of Contents Chapter 1: VisuaLink Command Fundamentals .................................................... 1-1 Summary ...................................................................................................
NDA-24233 Issue 2 Page vi VisuaLink 128/384 Engineering Guide List of Tables List of Tables Table 1: VIDEO Command .................................................................................................... 2-1 Table 2: AUDIO Command ............................................................
NDA-24233 Issue 2 Page 1-1 VisuaLink 128/384 Engineering Guide Chapter 1 Chapter 1: VisuaLink Command Fundamentals Preface Thank you very much for purchasing the VisuaLink 128 or VisuaLink 384. VisuaLink is suitable for a conference with one to three people on a site, and it is a device to realize a...
Page 1-2 NDA-24233 Issue 2 Chapter 1 VisuaLink 128/384 Engineering Guide 1.3 Physical/Electrical lnterface The external control port is at the back of the VisuaLink and uses DIN8 pin connectors. The maximum length of the control cable shall be no more than 20 ft. (6.1 meter) due to electric characte...
NDA-24233 Issue 2 Page 1-3 VisuaLink 128/384 Engineering Guide Chapter 1 1.4 Communication Format Communication between a console and VisuaLink 128/384 is done in a start-stop synchronization of the following format. Data Format Data Length: 7, 8 bit ASCII code Stop Bit: 1 bit Parity: Even, Odd, NON...
Page 1-4 NDA-24233 Issue 2 Chapter 1 VisuaLink 128/384 Engineering Guide Command Format Command: Transmit 4-character commands (only upper case can be used)Space: More than one space is transmitted between a command and a parameter Parameter: If a command requires a parameter, a parameter is assigne...
NDA-24233 Issue 2 Page 1-5 VisuaLink 128/384 Engineering Guide Chapter 1 1.5 Communication Procedure There is no procedure for communication between a console and VisuaLink as a rule. Therefore, a communication line is presumed to be error-free. When it is remotely operated with a modem, efficient o...
NDA-24233 Issue 2 Page 1-7 VisuaLink 128/384 Engineering Guide Chapter 1 1.6 Connecting and Incoming Call Control Basic Sequence Connecting and incoming call control basic sequence (when the incoming call mode of the VisuaLink receiving a call is set to the manual incoming call setting) is shown in ...
Page 1-8 NDA-24233 Issue 2 Chapter 1 VisuaLink 128/384 Engineering Guide This page is for your notes.
NDA-24233 Issue 2 Page 2-1 VisuaLink 128/384 Engineering Guide Chapter 2 Chapter 2: Console Command List Table 1: VIDEO Command Table 2: AUDIO Command Table 3: LINE Setting Command NO Feature Command Name Process 1-1 Setting Video Format SVFM Setting 1-2 Checking Video Format Setting RVFM Status 1-3...
Page 2-6 NDA-24233 Issue 2 Chapter 2 VisuaLink 128/384 Engineering Guide Table 32: Multi-point Related Report Command Table 33: Multi-Screen Related Report Command Table 34: Microphone Command Table 35: System Error Command Table 36: On-Screen Display Table 37: Current Power OFF Condition NO Feature...
NDA-24233 Issue 2 Page 3-1 VisuaLink 128/384 Engineering Guide Console Command List Chapter 3: Command Detailed Format Command details are described in this section according to the following format. Command Name Command Number Description: Describe command features. Command Format: Describe command...
Page 3-2 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.1 VIDEO Commands SVFM Setting Video Format 1-1 RVFM Checking Video Format Setting 1-2 Description: This sets video format. VisuaLink 128/384 is equipped with a feature to code active video with kinds of resolution....
NDA-24233 Issue 2 Page 3-3 VisuaLink 128/384 Engineering Guide Console Command List SPIP Setting Picture-in-Picture 1-3 RPIP Checking Picture-in-Picture Setting 1-4 Description: Sets PIP (small screen) display Command Format: SPIP p1 p2 p1: ON : PIP output ON OFF : PIP output OFF P2: RT : Display at...
Page 3-4 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SSND Setting Video Input Switch 1-5 RSND Checking Video Input Setting 1-6 Description: This sets video input switch. Command Format: SSND p1 p2 p1: L : local site R : remote site p2: C1 : Camera 1 C2 : Camera 2 Respo...
NDA-24233 Issue 2 Page 3-5 VisuaLink 128/384 Engineering Guide Console Command List SDSP Setting Monitor Output Video 1-7 Note: User will be unable to switch to STILL PICTURE if STILL PICTURE graphics has not been sent. RDSP Checking Monitor Output Video Setting 1-8 Description: Sets output video im...
Page 3-6 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SPDP Setting/Checking PIP Display Format 1-9 SPSW Setting/Checking PIP Image when Snapshot is Viewed 1-10 Description: Setting the display image seen in the picture-in-picture (PIP) window. Command Format: SPDP [p1] ...
NDA-24233 Issue 2 Page 3-7 VisuaLink 128/384 Engineering Guide Console Command List SCPI Setting/Checking Video Priority 1-11 S263 Setting H.263 1-12 Description: The VisuaLink has a function to automatically optimize the picture quality, (e.g., number of frames, resolution, coding, noise, etc.). In...
Page 3-8 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide R263 Checking H.263 Setting 1-13 Description: Reporting the current setting by S263 command Command Format: R263 Response: Normal Response: p1 OK p1: ON : H.263 available OFF : H.263 not available Error Response: ERR...
NDA-24233 Issue 2 Page 3-9 VisuaLink 128/384 Engineering Guide Console Command List 3.2 AUDIO Command SAMD Setting Audio Mode 2-1 RAMD Checking Audio Mode Setting 2-2 Description: Sets the audio coding format. The VisuaLink is capable of µ -Law PCM, SBADPCM and LP-CELP. Command Format: SAMD p1 p1: O...
Page 3-10 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SADL Setting Audio Delay 2-3 Description: Sets audio delay (lip sink). Delay is generated when video is coded in transmission, and the amount of delay differs depending on a transmission speed. On the contrary, audi...
NDA-24233 Issue 2 Page 3-11 VisuaLink 128/384 Engineering Guide Console Command List RADL Checking Audio Mode Setting 2-4 SMIC Setting MIC ON/OFF 2-5 Description: Checks the current audio delay setting Command Format: RADL p1 p2 p1: 64 : 56/64kpbs 2x64 : 2x56/2x64 kbps 3B : 168/192kbps 4B : 224/256k...
NDA-24233 Issue 2 Page 3-13 VisuaLink 128/384 Engineering Guide Console Command List SASW Setting Audio Input/Output Port 2-9 RASW Checking Audio Input/Output Port Setting 2-10 Description: Sets the audio input port and output port. Command Format: SASW p1 p1: LINE : LINE HEAD : HeadsetTEL : Telepho...
Page 3-14 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SMMT Sets Audio or Audio/Video Outgoing Mute Setting 2-11 RMMT Checking Audio or Audio/VideoOutput Mute Setting 2-12 Description: Sets whether the audio or audio and video outgoing is muted or unmuted at the start o...
NDA-24233 Issue 2 Page 3-15 VisuaLink 128/384 Engineering Guide Console Command List SMTC Sets Audio or Audio/Video Mute Setting 2-13 RMTC Checking Audio or Audio/VideoOutput Mute Setting 2-14 Description: Sets whether the audio or audio and video outgoing is muted or unmuted at the start of communi...
Page 3-16 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.3 LINE Setting Command SNET Setting Network Type (P x 64/56) 3-1 Note: The command can only be issued when the VisuaLink is not in a call. RNET Checking Network Type Setting (P x 64/56) 3-2 Description: Sets a net...
NDA-24233 Issue 2 Page 3-17 VisuaLink 128/384 Engineering Guide Console Command List NNSS Setting Transmission Line Type 3-3 Note: High Speed digital basic leased lines are currently only available in Japan. NNSI Checking Transmission Line Type Setting 3-4 Description: Sets the line interface: High ...
Page 3-18 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SLSP Setting Transmission Line Speed 3-5 RLSP Checking Transmission Line Speed Setting 3-6 Note: The response will always be a 64 kbps increment. It is recommended that the RNET command be used combined with RLSP. D...
NDA-24233 Issue 2 Page 3-19 VisuaLink 128/384 Engineering Guide Console Command List 3.4 DATA Command SDM2 Setting LSD Speed 4-1 Description: Setting Low Speed Data (LSD) port speed • Allows for H.281 far-end camera control • PC-to-PC data transmission Command Format: SDM2 p1 p1: OFF : OFF 1.2 : 1.2...
Page 3-20 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide RDM2 Checking LSD Speed Setting 4-2 SDM3 Setting MLP Speed 4-3 Description: Reporting the current LSD speed by SDM2 command Command Format: RDM2 Response: Normal Response: p1 OK p1: OFF : OFF 1.2 : 1.2 kbps 4.8 : 4....
NDA-24233 Issue 2 Page 3-21 VisuaLink 128/384 Engineering Guide Console Command List RDM3 Checking MLP Speed Setting 4-4 Description: Checks the current MLP speed setting. Command Format: RDM3 Response: Normal Response: p1 OK p1: OFF : OFF 4.0 : 4.0 kbps 6.4 : 6.4 kbps 14.4 : 14.4 kbps 24.0 : 24.0 k...
Page 3-22 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.5 ISDN Registering/Setting Command NDSS Registering My Number 5-1 Description: Registers a local dial number. In a communication, a local dial number is reported to the remote site at a call origination. The local...
NDA-24233 Issue 2 Page 3-23 VisuaLink 128/384 Engineering Guide Console Command List NDSR Checking My Number Registration 5-2 Description: Checks the current local dial number setting. In a communication, a local dial number is reported to the remote site at a call origination. This is used to check...
Page 3-24 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide MDST Registering Speed Dial 5-3 Description: VisuaLink can register a maximum of 130 speed dial numbers. A dial number that can be registered shall be 20-digit at a maximum with a sub address of a maximum of 8 digit...
NDA-24233 Issue 2 Page 3-25 VisuaLink 128/384 Engineering Guide Console Command List MDRD Checking Speed Dial Registration 5-4 Description: Checks the current registers speed dial number. Command Format: MDRD p1 p1: #xxx: speed dial number (xxx: speed number) Response: Normal Response: p1 p2 p3 p4 p...
Page 3-26 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide NBZS Setting Incoming Call Buzzer 5-6 Note: This command is ineffective when setting incoming mode is set to Automatic. Utilize this command only in the Manual Answer mode. NBZI Checking Incoming Call Buzzer Setting...
NDA-24233 Issue 2 Page 3-27 VisuaLink 128/384 Engineering Guide Console Command List SINC Setting Incoming Call Mode 5-8 Description: Sets the incoming call mode. There are three ways to receive an incoming call: manual incoming call mode, automatic incoming call mode, and selective incoming call mo...
Page 3-28 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SRNG Setting/Checking Incoming Call Buzzer at Auto Answer Mode 5-9 SPID Registering SPID 5-10 Description: Setting ringing times of incoming call buzzer in auto answer mode or selective answer mode Command Format: S...
NDA-24233 Issue 2 Page 3-29 VisuaLink 128/384 Engineering Guide Console Command List RPID Checking SPID 5-11 Description: Reporting current SPID Command Format: RPID p1 p1: L11 : Line1 Channel1 L12 : Line1 Channel2 L21 : Line2 Channel1 L22 : Line2 Channel2 L31 : Line3 Channel1 L32 : Line3 Channel2 R...
Page 3-30 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.6 Camera Related Registering/Setting Command CPPS Registering Camera Preset Position 6-1 CPNS Registering Talker Name 6-2 Description: Registers a camera preset position. Command Format: CPPS p1 p2 p3 [p4] p1: L1-...
NDA-24233 Issue 2 Page 3-31 VisuaLink 128/384 Engineering Guide Console Command List SCMK Setting Camera Model 6-3 RCMK Checking Camera Model Setting 6-4 Description: Sets types of camera which will be controlled. Command Format: SCMK p1 p1: S : EVI-D30 C : VC-C1 Response: Normal Response: OK Error ...
Page 3-32 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.7 Communication Status Reading Command RMAC Read Manufacturer Code 7-1 Description: Acquires manufacturer code of a remote site. Command Format: RMAC Response: Normal Response: p1 p2 p3 p4 p5 OK p1: 00-FF : Manufa...
NDA-24233 Issue 2 Page 3-33 VisuaLink 128/384 Engineering Guide Console Command List RMOD Read Common Mode During Communication 7-2 Description: Reads negotiated parameter setting. Command Format: RMOD Response: Normal Response: p1 p2 p3 p4 p5 p6 p7 p8 OK p1: 64 : 56/64 kbps 2x64 : 2x56/2x64 kbps 19...
Page 3-34 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide R221 Read H.221 Synchronous Status 7-3 RPNA Read Remote Site Name (at Point-to-Point) 7-4 Description: This reads a status of the H.221 frame specified in ITU-T Recommendation Command Format: R221 Response: Normal R...
NDA-24233 Issue 2 Page 3-35 VisuaLink 128/384 Engineering Guide Console Command List RCST Read Participating Conference Status 7-5 Description: This reads conference participating status. Command Format: RCST Response: Normal Response: p1 p2 OK p1: PP : point to point connection MP : multi-point con...
Page 3-36 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.8 Alarm Related Command CALM Read Alarm Status (1 of 2) 8-1 Description: Acquires alarm status. This is used to check the information of a generated alarm and the loopback status. Command Format: CALM Response: No...
NDA-24233 Issue 2 Page 3-37 VisuaLink 128/384 Engineering Guide Console Command List CALM Read Alarm Status (2 of 2) 8-1 Response p4: Bonding alarm D0: Bonding frame loss 0: normal 1: abnormal D1: Bonding speed negotiation fail 0: normal 1: abnormal D2: Network type negotiation fail 0: normal 1: abn...
Page 3-38 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.9 History Reading Command RLAM Read Communication/Alarm History 9-1 Description: Acquires communication history and alarm history. Command Format: RLAM p1 p2 p3 p1: L : communication history A : alarm history p2: ...
NDA-24233 Issue 2 Page 3-39 VisuaLink 128/384 Engineering Guide Console Command List 3.10 Registering Local Location Name Command MRNS Registering Local Site Name 10-1 Description: Registers a local site location name. Command Format: MRNS p1 p2 p1: xxxxxxxx : alphabet location name (within 16 chara...
Page 3-40 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.11 Serial Port Control Command SSIO Setting Serial Port 11-1 RSIO Checking Serial Port Setting 11-2 Description: VisuaLink is equipped with two serial ports, and four possible settings: T120 data conferenceCamera ...
NDA-24233 Issue 2 Page 3-41 VisuaLink 128/384 Engineering Guide Console Command List 3.12 Acquiring Version Command RVER Requesting Software Version 12-1 Description: Acquires the VisuaLink software version. Command Format: RVER Response: Normal Response:p1 p2 OK p1: xxxxxxxx : F/W version p2: xxxxx...
Page 3-42 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.13 Maintenance Command SLLB Setting Local Loopback 13-1 RLLB Checking Local Loopback Setting 13-2 Description: Sets local loopback process.VisuaLink is equipped with a loopback test point inside a terminal for aut...
NDA-24233 Issue 2 Page 3-43 VisuaLink 128/384 Engineering Guide Console Command List 3.14 Report Response Control Command ITCS Conference Status Report Control 14-1 IMCU Multi-point Conference Status Report Control 14-2 Description: Activation/deactivation of conference status reporting for thing su...
Page 3-44 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide I243 H.243 Report Control 14-3 ICGP Command Generator Related Report Control 14-4 Description: Activation/deactivation of H.243 multipoint conference status reporting for such things as: COPI / CSPI / CRPI / CVCI / ...
NDA-24233 Issue 2 Page 3-45 VisuaLink 128/384 Engineering Guide Console Command List 3.15 Maintenance and Other Command ISPR Setting Parameter Initialization 15-1 CRAM Clearing Backup Memory 15-2 RRST System Reset Request 15-3 Description: Initializes all VisuaLink values to factory default. Command...
Page 3-46 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide WCLK Setting System Clock 15-4 RCLK Checking System Clock Setting 15-5 Description: Sets the VisuaLink built-in system clock, date and time. Command Format: WCLK p1-p2-p3 p4:p5:p6 (p7) p1: yyyy : year p2: 01-12 : mo...
NDA-24233 Issue 2 Page 3-47 VisuaLink 128/384 Engineering Guide Console Command List 3.16 Mutli-point Conference Status Command RMNA Read Multi-point Conference Participating Location Name 16-1 Description: Acquires location name of all location participating locations in multi-point conference. Com...
Page 3-48 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide RMST Read Multi-point Conference Operation Status (NEC Specific) 16-2 Description: Acquires a status of a multi-point conference status when in activated for NEC specific multi-point conference. Command Format: RMST...
NDA-24233 Issue 2 Page 3-49 VisuaLink 128/384 Engineering Guide Console Command List RMPS Read Multi-point Conference Operation Status 16-3 RMMD Read Multi-point Conference Mode Status 16-4 Description: Acquires the multi-point conference status. Command Format: RMPS Response: Normal Response p1 p2 ...
Page 3-50 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.17 Model Identification Command RMES Read Model Identification 17-1 Description: Read model identification Command Format: RMES Response: Normal Response p1 p2 OK p1: TC2000_EC : VL128TC2000_6B : VL384 p2: F/W ver...
NDA-24233 Issue 2 Page 3-51 VisuaLink 128/384 Engineering Guide Console Command List 3.18 Audio Training Command ECTS Audio Training Command 18-1 Description: Initiate audio training. White noise is generated while 7 seconds. Command Format: ECTS Response: Normal Response OK Error Response: ERR01
Page 3-52 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.19 ISDN Control Command NCRN Requesting Connection 19-1 Description: Placing a BRI ISDN call. A call can be requested by either directly specifying a remote number or using an speed dial number. If using an speed ...
NDA-24233 Issue 2 Page 3-53 VisuaLink 128/384 Engineering Guide Console Command List NDSC Requesting Disconnection 19-2 NCIC Incoming Call Permit/Reject 19-3 Description: A disconnect in an BRI ISDN call. This command is used to execute a disconnection request and ending communication. Command Forma...
Page 3-54 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide NSTQ Communication Status Inquiry 19-4 Description: Gives a status on the ISDN communication. Command Format: NSTQ Response: Normal Response p1 p2 p3 p4 p5 p6 p7 OK p1: B : communication speed B 2B : communication s...
NDA-24233 Issue 2 Page 3-55 VisuaLink 128/384 Engineering Guide Console Command List 3.20 Camera Control Command CAMS Request for Camera Direction Change 20-1 Description: Sets camera head swing control. This command is valid only when an preset or auto mode camera is in use. A control of Camera 2 i...
Page 3-56 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.21 Option Control Command POCS Pointer Control 21-1 VCTS Talker Detection Control 21-2 Description: Activates or deactivates the on-screen pointer . The pointer is displayed at the remote monitor. This pointer can...
NDA-24233 Issue 2 Page 3-57 VisuaLink 128/384 Engineering Guide Console Command List STPR SnapShot Transmission Request 21-3 SXMR Standard Display Screen Setting Request 21-4 Description: Sends a snapshot (still graphic) image to the remote site. Command Format: STRP Response: Normal Response OK Err...
Page 3-58 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SXST Request to Acquire Composite Screen Setting 21-5 Description: Request for status on the various video screens displays. This command is only valid when going through an NEC multi-point control unit MCU5000A, th...
NDA-24233 Issue 2 Page 3-59 VisuaLink 128/384 Engineering Guide Console Command List 3.22 Multi-point Conference Control COPR Request to Chairman Control 22-1 Description: Acquires or deletes chairman control. Command is only valid when the VisuaLink is in a multi-point conference. Command Format: C...
Page 3-60 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide CSPR Multiple Address Transmission Request 22-2 Description: Acquires the simulcast transmission. Command Format: CSPR p1 p1: 0-255 : conference room number to be received * : composite screen display Note 1: When p...
NDA-24233 Issue 2 Page 3-61 VisuaLink 128/384 Engineering Guide Console Command List CRPR Specific Picture Reception Request 22-3 CMPR Request to Switch Multiple Address Originator Monitor 22-4 Description: Activates or deactivates selective receive mode. Command Format: CRPR p1 p2 p3 p1: 1-255 : re...
Page 3-62 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.23 Opening Control Command OMES Opening Message at Unit Activation 23-1 Description: Report opening message at power up. This is reported when the unit is automatically re-start due to some failure. In the case of...
NDA-24233 Issue 2 Page 3-63 VisuaLink 128/384 Engineering Guide Console Command List 3.24 Communication Status Report Command H221 H.221 Synchronous Status Report 24-1 IMAC Manufacturer Code Report 24-2 Description: H.221 reporting status change. Command Format: H221 p1 p1: AI : synchronization esta...
Page 3-64 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide IMOD Report of Common Mode in Communication 24-3 Description: Reports the negotiated mode during a communication. Command Format: RMOD p1 p2 p3 p4 p5 p6 p7 p8 p1: B/2B/3B/4B/5B/6B : communication speed p2: 56/64 : n...
NDA-24233 Issue 2 Page 3-65 VisuaLink 128/384 Engineering Guide Console Command List 3.25 Alarm Status Report Command RALM Alarm Status Change Report (1 of 2) 25-1 Description: Reports the VisuaLink alarm status. This is reported when alarm and loopback status is changed. Command Format: RALM p1 p2 ...
NDA-24233 Issue 2 Page 3-67 VisuaLink 128/384 Engineering Guide Console Command List 3.26 Video Status Report Command RVSR Incoming Video Synchronous Status Report 26-1 Description: VisuaLink monitors a synchronization status of a received video, and a report is made when a received video synchroniz...
Page 3-68 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.27 Participating Status Report Command ICST Participating Conference Status Report 27-1 Description: Reports participating conference status. Command Format: ICST p1 p2 p1: PP : point – point connection MP : multi...
NDA-24233 Issue 2 Page 3-69 VisuaLink 128/384 Engineering Guide Console Command List 3.28 ISDN Report Command NALT Display During Calling 28-1 NINC Incoming Call Report 28-2 NONL On-line Report 28-3 Description: Call report status an origination point. This means calling to remote site. Command Form...
Page 3-70 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide NDCI Disconnection Report 28-4 Description: Reports disconnecting the ISDN line. This is a report to show that communication is disconnected. Section 9 describes the disconnection reason. Command Format: NDCI p1 p2 ...
NDA-24233 Issue 2 Page 3-71 VisuaLink 128/384 Engineering Guide Console Command List 3.29 Camera Control Report Command CAMI Camera Status Report 29-1 CPNI Talker Name Display Report 29-2 Description: This is a status report on the remote camera condition. (When remote camera control is used) Comman...
Page 3-72 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.30 Option Control Report Command STEI SnapShot Transmission Ending Report 30-1 RFVR SnapShot Reception Report 30-2 Description: This is a report notifying a snapshot transmission is completed. Command Format: STEI...
NDA-24233 Issue 2 Page 3-73 VisuaLink 128/384 Engineering Guide Console Command List 3.31 Other Report Command CGSI Automatic Activation File Starting Report 31-1 CGEI Automatic Activating File Ending Report 31-2 Description: This is a report to show the start of auto executed file. Command Format: ...
Page 3-74 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.32 Multi-Point Related Report Command IMPS Multi-point Conference Operation Status Report 32-1 IMMD Multi-point Conference Mode Status Report 32-2 COPI Acquisition of Right to Operate Report 32-3 Description: This...
Page 3-76 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide CSSC SnapShot Transmission Permit Report 32-7 CMPI Multiple Address Originator Monitor Video Switch Report 32-8 CJNI Terminal Connection Report 32-9 Description: This report is a request to transmit a snapshot. Comm...
NDA-24233 Issue 2 Page 3-77 VisuaLink 128/384 Engineering Guide Console Command List CSTI Conference Status Report 32-10 Description: This is to report the multi-point conference status. This is reported only in a NEC specific multi-point conference. Command Format: CSTI p1 p2 p3 p4 p5 p6 .............
Page 3-78 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.33 Multi-Screen Related Report Command XMII Composite Screen Setting Report 33-1 XMCI Standard Display Screen Setting Report 33-2 Description: Reports a composite screen setting. Command Format: XMII p1 p2/p3 p4=p...
NDA-24233 Issue 2 Page 3-79 VisuaLink 128/384 Engineering Guide Console Command List XSCI Response to Composite Screen Setting Request 33-3 Description: This is a response report of composite screen setting/acquisition request. Command Format: XSCI p1 p1: OK : normal ERRxx : NG
Page 3-80 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.34 Microphone Command PPNI Voice Activate Microphone Report 34-1 Description: Report microphone that inputs the voice Command Format: PPNI p1 p1: 1 to 3
NDA-24233 Issue 2 Page 3-81 VisuaLink 128/384 Engineering Guide Console Command List 3.35 System Error Command ERRI System Error Report 35-1 Description: Report system error Command Format: ERRI p1 p1: [S_RAM] BACKUP ERROR: SRAM error [SYSTEM] BACKUP ERROR: System parameter error[M_DIAL] BACKUP ERRO...
Page 3-82 NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.36 On-Screen Command SOSD Setting On-Screen Display 36-1 Description: Sets the On-Screen displays for the VisuaLink Command Format: SOSD p1 p1: ON: Activates the On-Screen Message OFF: Deactivates the On-Screen Me...
NDA-24233 Issue 2 Page 3-83 VisuaLink 128/384 Engineering Guide Console Command List 3.37 Current Power OFF Condition CSTB Current Power OFF Condition 37-1 Description: Set and read the current Power OFF Condition. The CODEC outputs black video when no user intervention has been acted on for a perio...
NDA-24233 Issue 2 Page 4-1 VisuaLink 128/384 Engineering Guide Error Response Table 4: Error Response Table If a command input from console is not understandable or has a different configuration, an error response is transmitted to the console. Error responses are shown in the following table. Table...
NDA-24233 Issue 2 Page 5-1 VisuaLink 128/384 Engineering Guide Factors of Disconnections 5: List of Factors for Disconnection in Table Location of Factors for DisconnectionLU: Local User LN: Local Network TN: Transit Network RU: Remote User RN: Remote Network Number Message Factors for Disconnection...
NDA-24233 Issue 2 Page A-1 VisuaLink 128/384 Engineering Guide Appendix A Appendix A: Pin-out Specification Pin-out specifications for all the VL 128/384 connectors. SERIAL 1 PORT Note: The signal direction shown is seen from the VisuaLink 128 (DTE). SERIAL 2 PORT Note: The signal direction shown is...
Page A-2 NDA-24233 Issue 2 Appendix A VisuaLink 128/384 Engineering Guide S/T Line (ISDN Connection) Note 1: The signal direction shown is seen from the VisuaLink 128 (DTE).Note 2: Pins 1, 2, 7, and 8 are not used. Telephone Connection S-Video Socket Input/Output PIN # Symbol Function Polarity 1 a 2...
NDA-24233 Issue 2 Page B-1 VisuaLink 128/384 Engineering Guide Appendix B Appendix B: Line Speed Specifications X : cannot set ∆ : can set but video is not transmitting : snapshot not available X : cannot set 1B (64kbps) Line Speed Audio Algorithms G.711 µ -Law PCM G.722 SB-ADPCM G.728 LD-CELP Mute ...
NDA-24233 Issue 2 Page C-1 VisuaLink 128/384 Engineering Guide Appendix C Appendix C: ISDN Q.931 Cause Code Definitions The following table defines the Q.931 cause codes that the VisuaLink 128/384 writes to event files. Q.931 specification defines the layer-3 protocol for two connected ISDN devices....
NEC Manuals
-
NEC nec
Manual
-
NEC LCD172VXM
Manual
- NEC IP8800/S6600 Manual
-
NEC PSIII
Manual
-
NEC XV17+
Manual
-
NEC LCD1860NX
Manual
-
NEC PA322UHD
Manual
-
NEC Versa M540
Manual
-
NEC LCD224WMX
Manual
-
NEC SP4620
Manual
-
NEC 0612-20
Manual
-
NEC PX-50XM5A
Manual
-
NEC 46 V462
Manual
-
NEC MT1055
Manual
-
NEC PD75402A
Manual
-
NEC NP-V311X
Manual
-
NEC LT240K, LT260K
Manual
-
NEC DTR-IR-2
Manual
-
NEC j
Manual
-
NEC PD78052(A)
Manual