NEC IDC3000 - Manuals

NEC IDC3000 – Manual in PDF format online.

Manuals:

Manual

Manual NEC IDC3000

Summary

Page 2 - CAUTION; ATTENTION; DOC Compliance Notice

WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UN- LESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSID...

Page 3 - CONTENTS; FEATURES

CONTENTS FEATURES ..................................................... 1 WARNINGS AND PRECAUTION ................... 2 PART NAMES AND FUNCTIONS .................. 4 FRONT PANEL ......................................................... 4 INDICATORS ......................................................

Page 4 - AVERTISSEMENT

Warnings and Safety Precaution The NEC IDC-3000 is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Use a soft clothand if necessary, mild detergent. Do not use commercial spray cleanerswhich may damage the surface. In case of damage, a...

Page 5 - PART NAMES AND FUNCTIONS; FRONT PANEL; MODE 2 Button; POWER Button; DOWN and UP Buttons

PART NAMES AND FUNCTIONS REMOTE EXT POWER STAND-BY SCAN CONVERTER IDC-3000 VIDEO NTSC PAL 1 2 3 4 5 MONITOR RGB NOISE REDUCTION MOVIE STILL MODE1 DOWN UP MODE2 NR MOVIE STILL VIDEO1 VIDEO2 VIDEO3 VIDEO4 VIDEO5 MONITOR RGB NORMALIZE 1 2 1 2 3 NORM. SET 3D 3D 6 7 8 FRONT PANEL 1 2 4 5 3 D C 9 0 A B 4 ...

Page 6 - INDICATORS

VIDEO NTSC PAL 1 2 3 4 5 MONITOR RGB NOISE REDUCTION MOVIE STILL 1 2 1 2 3 INDICATORS 6 NR Button Used when screen noise becomes annoying. Each time this button ispressed, the NR function will change as follows: → OFF → NOISE REDUCTION1 → NOISE REDUCTION 2 (Noise is reduced) (Noise is further reduce...

Page 7 - REAR PANEL; AUTO POWER Switch

VIDEO 1 S-VIDEO AUDIO L R VIDEO 2 S-VIDEO AUDIO L R VIDEO 3 AUDIO L R VIDEO 4 AUDIO L R VIDEO 5 AUDIO L R INPUT AUDIO L R RGB (THROUGH) MONITOR VIDEO1 • 2 S ONLY AUDIO L R R G B HORIZONTAL VERTICAL H/V AUDIO L R PC-CONTROL EXTERNAL CONTROL OUTPUT H V HV-POL. PC-CONTROL AC IN VIDEO 1 VIDEO 2 BNC S-VI...

Page 8 - AC IN Receptacle; EXTERNAL CONTROL Connector

8 MONITOR Output Jack (OUTPUT) MONITOR (BNC) ........... Outputs the signals of the equipment con- nected to VIDEO 1 through 5. S-VIDEO .......................... Outputs an S video signal, (derived from the signal of the equipment connected toVIDEO 1 or VIDEO 2), which has beendivided to a luminanc...

Page 9 - REMOTE CONTROL

REMOTE CONTROL 3 1 2 9 E 7 4 5 6 0 POWER VIDEO1 RGB SPLIT VIDEO2 VIDEO3 NORMALIZE MODE1 VIDEO4 UP MODE2 DOWN REMOTE CONTROL UNIT RD-338E MONITOR VIDEO5 NOISE REDUCTION MOVIE STILL D C 8 B A F B 1 POWER Button Turns the power on or off. 2 VIDEO 1 Button Switches the unit to the video 1 input mode. 3 ...

Page 10 - REMOTE CONTROL NOTES; Remote Control Precautions; Installing the Batteries of the Remote Control

REMOTE CONTROL NOTES Remote Control Precautions v The remote control system may not function when direct sunlight orstrong illumination strikes the remote sensor window of the main unit. v Do not place in locations where there is a high temperature or highhumidity. Doing so will lead to breakdown. v...

Page 11 - ADJUSTMENT; Adjustment of SPLIT and MOVIE

ADJUSTMENT Adjustment of COLOR, TINT, SHARPNESS, and SOUND (1) Press the MODE 1 button and select the mode to be adjusted. Each press of the MODE 1 button will change the selection as follows: → COLOR → TINT → SHARPNESS → SOUND (2) While the indicator is on, press and hold the UP or DOWN button and ...

Page 12 - Screen Display During STILL Mode Selection

ON-SCREEN DISPLAY Screen Display During Input Signal Selection Screen Display During DVNR (Noise Reduction) Selection Display characters during video 1 to 5 input signal selectionDuring video 1 input signal selection .......... SOURCE VIDEO 1 During video 1 S input signal selection ....... SOURCE S-...

Page 13 - During the NTSC COLOR Adjustment; Screen Display During NORMALIZED Selection; Screen Display During Split Mode Selection

During the NTSC COLOR Adjustment Display characters during the color adjustmentDuring NTSC ............................................... COLOR Display colorCOLOR ........................................................ GreenBar Normal .............................................. MagentaMax ........

Page 14 - During the SHARPNESS Adjustment

During the TINT (Center) Adjustment TINT R G Display characters during the tint adjustment Display color during the center adjustmentTint .............................................................. GreenR ................................................................. RedG ........................

Page 15 - During the SOUND Adjustment; During the MOVIE Mode Selection; During the SPLIT Screen Selection

SOUND – + During the SOUND Adjustment Display characters during the sound adjustment Display colorSOUND ........................................................ GreenBar Normal .............................................. MagentaMax ................................................... RedMin .........

Page 17 - Using the EXTERNAL CONTROL Connector; Using the PC-CONTROL Connector

Using the EXTERNAL CONTROL Connector 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 Mini D-SUB 15 Pin Function Table Function Pin No. External control ON External control OFF POWER ON POWER OFF VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 RGB 14-15 SHORT OPEN 5-15 SHORT OPEN 8-15 SHORT OPEN SHORT OPEN SHORT OPEN 3-...

Page 19 - RACK MOUNTING

RACK MOUNTING Use the accompanying rack mount bracket to mount the IDC-3000 to therack. NOTE: This rack mount bracket is designed for used with EIA standard racks. 1 Remove the four (A) screws from the IDC-3000. 2 Use the screws removed in Step 1 to fasten the supplied rack mountbracket (B) to the I...

Page 20 - SPECIFICATIONS

SPECIFICATIONS X Input impedance: 75 Ω 1.0 Vp-p Y: Input impedance: 75 Ω 1.0 Vp-p C: Input impedance: 75 Ω 0.28 Vp-p (Burst level) Input impedance: 22 k Ω or greater 0.5 Vrms Output impedance: 75 Ω 1.0 ± 0.1 Vp-p (with 75 Ω termination) Y: Output impedance: 75 Ω 1.0 ± 0.1 Vp-p (with 75 Ω termination...

Page 21 - APPENDIX; Interface Condition; Control Data Format

APPENDIX (IDC-3000 stand alone PC-CONTROL command reference) You can control the main functions from external equipment such aspersonal computer using the PC-CONTROL terminal. The followingsections explain the interface. Interface Condition • RS-232C or RS-422• Baud rate ...............................

Page 22 - PC CONTROL COMMAND LIST FOR USE WITH THE IDC-3000

PC CONTROL COMMAND LIST FOR USE WITH THE IDC-3000 COM2 4E 4F 47 COM1 9F DF Contents Power On Power Off Input switching Length 00 00 01 COM1 3F COM2 4E 4F 47 Contents Power On (ACK) Power Off (ACK) Input switching (ACK) Length 00 00 00 \ PC → IDC-3000 IDC-3000 → PC Example: Input switching (VIDEO 1) ...

Page 23 - PROFESSIONAL GRAPHICS PRODUCTS; LIMITED WARRANTY

` PROFESSIONAL GRAPHICS PRODUCTS LIMITED WARRANTY NEC Technologies, Inc. (hereafter NECTECH) warrants this product to befree from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Parts and labor are warranted for (1) One Year from the date of the firstcustomer ...

Page 24 - • MEMO •