NEC 5140 - Manuals

-4- CUSTOMIZING YOUR 5140 APPLIANCE Ringer Control To adjust the Ringer Volume while 5140 IP Appliance is ringing: z Press the volume control buttons located above the display. To adjust the Ringer Volume or Pitch while the 5140 IP Appliance is idle: 1. Press SETTINGS. 2. Press the More command key....

-5- Quick Key Programming You can program your quick keys using the 5140 IP Appliance or the Desktop Tool. The Desktop Tool is a companion application for the 5140 IP Appliance that runs on a PC. It allows you to label the quick keys that you programmed. The labels appear on the display and cannot b...

-6- MAKING AND ANSWERING CALLS Make a call 1. If necessary, press PHONE VIEW to exit the current application. „ Press the quick key associated with the party you want to call. „ Dial the number using the dialpad keys. 2. Continue the call using the speakerphone or lift the handset. Answer a call Do ...

-7- Speed Call - Personal To store a personal Speed Call number: 1. Press SETTINGS. 2. Press the More command key. 3. Press Speed Call command key. 4. Press a quick key that isn't a line key. 5. Do one of the following: „ To enter a new number, dial the number. „ To enter the last number dialed, pre...

-8- Auto-Answer This feature automatically connects internal calls to your extension. Calls are announced by a single burst of ringing; then, the microphone and speaker are activated and the call is answered. You can continue the call handsfree or use the handset. To enable or disable Auto-Answer: z...

-9- Transfer To Transfer an active call: 1. Press Trans/Conf command key. 2. Dial the number of the next party. 3. Do one of the following: „ To complete the Transfer, hang up or press the Release Me command key. „ To announce the Transfer, wait for an answer, consult, and then hang up. „ To return ...

-10- Add Held To move a call on Hold to another line appearance: 1. Press the available line key. 2. Press the Add Held command key. 3. Press the line key with the flashing icon. To add a call on Hold to an existing conversation or conference: 1. Press the Add Held command key. 2. Press the line key...

-11- Call Forward Call Forward lets you redirect incoming calls to an alternate number when your phone is busy, when you're not answering, or all the time. "Busy" (Internal, External, and Both) redirects your calls when your telephone is busy. "No Answer" (Internal, External, and Bot...

-12- To cancel Call Forward: 1. Press SETTINGS. 2. Press the More command key. 3. Press the Forwarding command key. 4. Select the type of call forwarding. 5. Press the Save/off command key. 6. Press SETTINGS to exit the Settings menu. Call Forward - Remote To forward calls from a remote extension to...

-13- Call Forward - End Chaining To ensure that calls do not get forwarded again by the destination number: 1. Lift the handset. 2. Dial 64. 3. Hang up. To again allow calls to be forwarded by the destination number: 1. Lift the handset. 2. Dial **73. 3. Hang up. Call Forward - Forced To force an in...

-14- Messaging - Callback To leave a message waiting indication on a telephone when you hear busy or ringback tone: z Press Leave A Msg command key. To respond to a message waiting condition on your telephone: Do one of the following: z Press Messaging followed by Call. z Lift the handset, and then ...

-16- USING OTHER FEATURES Account Codes An account code is a series of digits that you assign to your calls, usually for accounting purposes. The code identifies the account in the call records that your system generates. A forced account code is usually entered from another extension, enabling you ...

-17- Callback To request a Callback when you reach a busy or unanswered station: z Press the Call Me Back command key. To answer a Callback: z Lift the handset. To view and/or cancel outstanding Callbacks: 1. Press SETTINGS. 2. Press the More command key. 3. Press the Callbacks command key. 4. Press...

-18- Call Park The Call Park feature allows you to place a call in a special hold state. You, or someone else, can then retrieve the call from any extension in the system. After parking the call, the system can automatically connect you to paging equipment so that you can announce the call to the re...

-19- Call Pickup To answer a call that is ringing at another extension in your Pickup Group: 1. Lift the handset. 2. Press the Pickup Call command key. (See Quick Key Programming for instructions on programming features to your phone.) To answer a call that is ringing at a extension not in your Pick...

-20- Do Not Disturb To activate or deactivate Do Not Disturb: z Press the Do Not Disturb quick key. To activate Do Not Disturb from a remote extension: 1. Lift handset. 2. Dial **5. 3. Dial the number of the station to which Do Not Disturb is to apply. 4. Hang up. To deactivate Do Not Disturb from a...

-21- Direct Paging Direct Paging allows you to page a party through their telephone speaker. To page another extension user: 1. Lift the handset. 2. Press the Direct Paging quick key. (See Quick Key Programming for instructions on programming features to your set.) 3. Dial the extension number. 4. S...

-22- Reminder To program a Reminder: 1. Press SETTINGS. 2. Press the Reminder command key. 3. Enter the time in 24-hour format. 4. Press the Save command key. 5. Press SETTINGS to exit the Settings menu. To view, change, and/or cancel a pending Reminder: 1. Press SETTINGS. 2. Press the Reminder comm...

-23- Headset Operation (with Feature Control Switch) IMPORTANT NOTE: Mitel Networks Headsets with Feature Control Switch must be installed in the dedicated headset jack on the back of the phone. Installation will disable your handset microphone. Disconnecting the headset at the jack or at the quick-...

-24- Calculator To use the Calculator: 1. Press SETTINGS. 2. Press the Calculator command key. 3. Use the telephone keypad as the numeric keypad. The * key is used as a decimal point key. The following operations as well as the Clear Entry/Clear (CE/CLR) and another decimal point are presented as co...

-25- Group Paging / Meet Me Answer Group Paging allows you to page a group of telephones through their built-in speakers. You can belong to as many as three paging groups with one group designated as your "prime" group. When you need to respond to a Group Page but don't know the identity or ...

-26- Trunk Flash The Trunk Flash feature allows you to access Centrex features (if available) while you are talking on an outside call. To flash a trunk while talking on an outside call: 1. Press Trans/Conf. 2. Dial *57 for a single flash or *56 for a double flash. 3. Wait for dial tone. 4. Dial the...

-27- Record a Call This feature uses your voice mail system to record your telephone conversations. Note: You may be required by law to inform the other party that you are recording the conversation. For specific instructions, consult your System Administrator. To start recording while on a two-part...

-28- Hot Desking Hot Desking allows you to log into the telephone system from any phone designated as a Hot Desk phone. Simply log in at the phone using your assigned Hot Desk User Extension Number and the phone immediately assumes all your speed dials, features keys, call forwarding setup, and line...

-29- Tag Call Tag Call allows you to signal that you are the victim of a threatening or malicious call. Using the tag, your system administrator or telephone company can identify the source of the call and provide this information to appropriate personnel or authorities. CAUTION: Tagging a non-malic...

-30- USING THE APPLICATIONS Personal Directory The Personal Directory provides easy access to your personal address book. The main screen of the directory is your control center for all personal call management. From this screen, you can search entries and make calls. Note: Use the Desktop Tool to a...

-31- Corporate Directory The Corporate Directory is created and maintained by your System Administrator. From the Corporate Directory screen, you can perform searches, make a call, and view details on entries in the directory. To access the Corporate Directory: 1. Press ONLINE SERVICES. 2. Press Cor...

-32- Call Logs Call Logs track up to 60 of your incoming, outgoing, and missed calls. It provides the name of each called or calling party, the date and time of the call, the phone number, call duration, and the number of calls to or from that particular party. To access Call Logs: z Press CALL LOGS...

-33- Speed Dials Speed Dials is an application that allows access to a list of phone numbers that you can dial with one or two key presses. Use the Desktop Tool to to add numbers to the list. To make a Speed Dial call: z Press SPEED DIALS, and then press a quick key associated with a speed call that...

-34- Online Services Online Services provides access to applications and information programmed by your System Administrator for your use. Online services can include company news and events, and company stock quotes. To access Online Services: z Press ONLINE SERVICES, and then press the quick key a...

-35- Mitel Networks IrDA Module The Mitel Networks IrDA (Infrared Display Adapter) Module provides a wireless connection between Mitel Networks' IP-based ICP and the Palm Handheld Personal Digital Assistant (PDA). The IrDA Module's Dial by Address Book (DBAB) application enhances the PDA's existing ...

-36- Speech Recognition Speech Recognition is an optional feature that allows you to interact with the system using your voice. With Speech Recognition, you can call people by saying their name and interact with the voice mail system using spoken commands. You can take a tutorial from your phone to ...

-37- USING VISUAL VOICE MAIL Visual Voice Mail is an application that allows you to visually interact with the voice mail system. Before you can use voice mail, you must first set up your mailbox. To set up your mailbox: 1. Press VOICE MAIL. 2. Enter the default passcode ( 999 ). 3. Press the Login ...

-38- About the Voice Mail main screen The Voice Mail main screen contains a chronological list of the voice messages in your mailbox, with the most recent message listed first. By default, the first message is selected when the main screen opens. You can scroll through the messages by using the Navi...

-39- Sorting Messages By default, messages display in the order in which they were received from most to least recent. You can re-sort your messages to display, z new messages first, and then the saved messages, z alphabetically according to the sender's name with unknown callers listed at the end, ...

-40- Playing messages To play messages: 1. Access your mailbox. 2. Use the Navigation keys to select the message that you want to play. 3. Press the Play Messages command key. While listening to a Message you can press After listening to a message you can press to skip to the end of message to fast ...

-41- Making and Replying to Messages To reply to a message: 1. Use the Navigation keys to select the message to which you want to reply. 2. Press the Reply command key. 3. Press the Record a Reply command key. 4. Record your message (see Recording Options below). 5. (Optional) Press the Add Recipien...

-43- Recording Memos To record a memo to yourself: 1. Access your mailbox. 2. Press the More Choices command key repeatedly until Record Memo appears. 3. Press the Record Memo command key. 4. Press to start recording. (See the previous page for recording options.) 5. Press the Done command key. 6. P...

-44- Changing your Greetings, Name and Passcode When you first set up your mailbox you recorded a greeting and your name and selected a passcode. The User Options menu allows you to change these at any time. There are two types of mailbox greetings: "permanent" and "temporary". You r...