Msd 5520 Street Fire Ignition Control Installation- Manuals

Page 2 - MOUNTING; supplied self tapping screws to mount the box.; unit cut the loops as shown in Figure 1.; LED; ground wire to a clean, paint free metal surface.; WIRE FUNCTIONS; Figure 1 Selecting the number; CYLINDER SELECT

2 I N S T A L L A T I O N I N S T R U C T I O N S S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 MOUNTING The Street Fire Ignition can be mounted in most positions, except directly upside down (if upside down, moisture or wat...

Page 3 - ROUTING WIRES; REV LIMITER; PRESTART CHECK LIST; Common Mag Pickup Wires; Colors; COIL; NOTE: On dual point setups, it is recommended; Figure 3 Adjusting the Rev Limiter.

I N S T A L L A T I O N I N S T R U C T I O N S 3 S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Ballast Resistor: If your vehicle has a ballast resistor in line with the coil wiring, it is recommended to bypass it. ROUTING W...

Page 4 - GM IGNITIONS Wiring with an MSD Wiring Harness.; MSD SYSTEMS Installing to an MSD Distributor.; NOTE: Cut and splice the two Pink wires

4 I N S T A L L A T I O N I N S T R U C T I O N S S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Harness PN 8876 - Dual Connector Coil. Harness PN 8877 - 1996-on GM Vehicles. GM IGNITIONS Wiring with an MSD Wiring Harness....

Page 5 - NOTE: The GM Ignition Module is removed; and replaced with the supplied PN; GM IGNITIONS GM Large Cap HEI Distributors

I N S T A L L A T I O N I N S T R U C T I O N S 5 S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 GM IGNITIONS Wiring an HEI 4-pin Module (Magnetic Pickup Trigger). GRAY TO TACH WWW.STREET-FIRE.COM PN 5520 CDI MULTI-SPA RK...

Page 6 - FORD IGNITIONS Wiring a Ford DuraSpark using White Wire Trigger.; NOTE: Some 5-pin models may exper ience a; hesitation or stall on deceleration. If this

6 I N S T A L L A T I O N I N S T R U C T I O N S S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 FORD IGNITIONS Wiring a Ford DuraSpark using White Wire Trigger. COIL GRAY TO TACH WWW.STREET-FIRE.COM PN 5520 CDI MULTI-SPA ...

Page 7 - FORD IGNITIONS Wiring a Ford TFI with Harness, PN 8874.

I N S T A L L A T I O N I N S T R U C T I O N S 7 S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 MAGNETIC PICKUP CONNECTOR PN 8860 HARNESS BLAC K ORANGE WHITE (NOT USED) COVER W/TAPE + FORD DISTRIBUTOR VIOLET ORANGE VIOLET BL...

Page 8 - AFTERMARKET COMPONENTS Wiring to a Pertronix Ignitor Kit.; MSD SYSTEMS Installing to an MSD Distributor PN 8360.; NOTE: The ignition module of the PN 8360; still triggers the Street Fire Ignition.

8 I N S T A L L A T I O N I N S T R U C T I O N S S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 CHRYSLER IGNITIONS Wiring a Chrysler Electronic Ignition using Magnetic Pickup Trigger. COIL GRAY TO TACH WWW.STREET-FIRE.COM...

Page 9 - TROUBLESHOOTING; installation or poor connections.; Tachometer Compatibility List; AFTERMARKET TACHOMETER; Tach Output wire on the Street Fire Ignition.

I N S T A L L A T I O N I N S T R U C T I O N S 9 S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 TROUBLESHOOTING Every Street Fire Ignition undergoes numerous quality control checks including a four hour burn-in test. If you ...

Page 10 - PN 8910: If your tachometer was triggered from the coil negative; BALLAST RESISTOR

10 I N S T A L L A T I O N I N S T R U C T I O N S S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 ENGINE RUN-ON If your engine continues to run even when the ignition is turned Off you are experiencing engine Run-On. This usu...

Page 11 - Figure 5 Installing the Diode to fix Run-On.; Most other applications: On other applications; where engine Run-On is experienced, a Resistor; Figure 6 Wiring the Dual Ballast Resistor for Run-On.

I N S T A L L A T I O N I N S T R U C T I O N S 11 S T R E E T F I R E • W W W . S T R E E T - F I R E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 1A-400V DIODE TO CHARGING LIGHT SPLICE HERE OR DELCOTRON ALTERNATOR FORD VEHICLES ATTACH DIODE TO TERMINAL "1" EARLY GM...

Page 12 - CHECKING FOR SPARK; If triggering the ignition with the White wire:; Limited Warranty; for custom applications.; S T R E E T F I R E; Figure 7 Checking for Spark with the White Wire.; WHITE WIRE TRIGGER; MAGNETIC PICKUP TRIGGER; Service; returning MSD components for warranty service,; issued to them before

CHECKING FOR SPARK If triggering the ignition with the White wire: 1 Make sure the ignition switch is in the "Off" position. 2. Remove the coil wire from the distributor cap and set the terminal approximately 1/2" from ground. 3. Disconnect the White wire from the distributor's points or...