Msd 2351 Programmable Fuel Pump Voltage Booster Instal- User Manual
Msd 2351 Programmable Fuel Pump Voltage Booster Instal– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – MSDVIew SOFTwARe INSTALLATION; ON; LED ALERTS; OFF; BLINKING TWO DIGIT FAULT CODES; Figure 3 Select Install Folder.
- Page 3 – TUNING; Figure 5 Hardware Wizard.
- Page 4 – USING The MSDVIew SOFTwARe; Figure 7 Gauge Selector Box.; Limited warranty; Proof of Purchase; M S D I G N I T I O N
M S D I G N I T I O N
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
MSD Programmable Fuel Booster
PN 2351
Parts Included:
1 - Programmable Fuel Booster, PN 2351
1 - Software CD
1 - Parts Bag
1 - Harness
1 - USB Cable
Figure 1 Recommended Wiring, General Application.
USB PORT
ALERT LED
ORANGE
CUT
FACTORY 12 VOLTS
FROM INERTIA SWITCH
RED
1/8” DIAMETER VACUUM
HOSE TO INTAKE MANIFOLD
RED
BLACK
FUEL PUMP +
INDICATES CONNECTION
X
The Programmable Fuel Pump Booster will increase the voltage to the fuel pump in proportion to manifold
boost pressure. The maximum voltage output is 22. The minimum output will be the battery voltage.
Note:
It is recommended to have the Service Manual for your vehicle to identify the original wiring and fuel
pump relay.
RATING:
Continuous Power: 275 Watt, Peak Power: 375 Watt (one minute)
INSTALLATION
The MSD Fuel Pump Booster must be wired inline with the factory fuel pump relay. The factory has safety
features built in, such as an inertia switch and high pressure shut-off which must be retained.
The MSD Fuel Pump Booster can be mounted in any position and is completely potted with a polyurethane
compound for vibration resistance. Keep the unit away from direct engine heat sources and make sure all
of the wiring reaches their connections. Also, allow access to the USB port.
Use the unit as a template and mark the mounting holes. Remove the unit and drill the holes using a 3/16"
bit. Mount the unit with the
supplied screws. With the
unit mounted, route the wiring
to their connections. Also
connect the boost pressure
line to the booster and intake
manifold (Figure 1).
ORANGE (18-GAUGE, long)
OEM Fuel Pump Power (12V)
WIRING
RED (12-GAUGE, long)
RED (12-GAUGE, short)
BLACK (12-GAUGE, short)
Pump (+) Positive lead to Fuel Pump
Battery (+) 12V
Battery (-) Ground
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 MSDVIew SOFTwARe INSTALLATION In order to install and run the MSDView software, t h e f o l l o w i n g m i n i m u m r e q u i r e m e n t s a r e re...
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 TUNING It is recommended to have a fuel pressure gauge when testing and tuning with the Programmable Fuel Pump Booster. The fuel pressure should hold ...
USING The MSDVIew SOFTwARe With the MSD connected, open the software by clicking the icon on your desktop. The screen will prompt for the MSD product part number (PN 2351) to be selected. The MSD software is a Graphical User Interface (GUI) design that incorporates the familiar Windows style operati...
