Msd 82933 Modified Distributor Cap and Rotor for Acura- User Manual
Msd 82933 Modified Distributor Cap and Rotor for Acura– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – ASSEMBLING THE COIL WIRE; Figure 5 Identifying the Different; ROTOR RETAINING SCREW; Figure 4 Replacing the Rotor.; REMOVE DUST COVER
- Page 3 – Figure 6 Stripping the Sleeve.; STRIPPING THE WIRE; Note: It is normal for the conductor to retract into the
- Page 4 – Figure 10 Crimping the Terminal.; M S D I G N I T I O N; Limited Warranty; for special or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before
M S D I G N I T I O N
• W W W . M S D I G N I T I O N . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
Parts Included In This Kit
1 - Distributor Cap
1 - Coil Wire
MSD Modified Honda Distributor Cap & Rotor
PN 82903, PN 82923 & PN 82933
WARNING: During installation, disconnect the battery cables. When disconnecting the battery
cables, always remove the Negative cable first and install it last.
1 - Rotor
1 - Parts Bag
1 - Mini-Stripper-Crimper
Note: The Modified Cap is designed so that you can remove the stock internal coil, and use a higher output
external coil. The stock internal coil MUST be removed before the installation of this cap. Failure to
do so will cause damage to the MSD cap.
Note: Spark plug style, 90° terminals are required
with this MSD cap.
INSTALLATION:
1. Mark the location of each plug wire on the
distributor cap, then remove the wires. Remove
the stock distributor cap, rotor and dust cover.
2. Locate the coil wires and note their color and
location. On the majority of Honda or Acura
engines, the Black/Yellow wire is positive. The
coil negative wire is generally White/Blue, Blue,
Green/Yellow or Green. In some cases, the coil
itself is marked negative (-) and positive
(+).
Note: If you have a question as to the wires’
polarity, use a volt-meter and probe
each wire with the ignition key turned
to the On position. Coil positive will
show 10-12 volts.
3. Once you determine the polarity of the
coil wires you will need to extend the
wires to reach the MSD external coil. Cut
the factory terminals off and solder them
to 14-gauge wiring. Seal the soldered joint
with shrink sleeve or electrical tape.
4. Depending on the model of distributor
you have, you may need to drill a hole
in the new cap to route the wires out. In
some applications the factory rubber
seal is thick enough to cut and slide the
new wires out.
Figure 1 Primary Wiring with the Coil Removed.
Figure 2 Wiring with a Blaster SS Coil.
ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered
in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product
will help if there is ever a warranty issue with your product and helps the MSD R&D team create
new products that you ask for! Go to www.msdignition.com/registration.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D I G N I T I O N • W W W . M S D I G N I T I O N . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 ASSEMBLING THE COIL WIRE Once the cap is installed and the coil is wired, you will need to assemble a coil wire. You will need a razor blade and a 4...
INSTALLATION INSTRUCTIONS 3 M S D I G N I T I O N • W W W . M S D I G N I T I O N . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 6 Stripping the Sleeve. Figure 8 Positioning the Wire in the Terminal. Figure 7 Preparing the Terminals. Figure 9 Crimping a Dual Crimp Termi...
Figure 10 Crimping the Terminal. 5. Put the assembly into a vise making sure the alignment tabs are on the outside edge of the vise jaws (Figure 10). 6. Slowly close the vise making sure the tool and terminal stay properly positioned and aligned. Stop applying pressure when the terminal ends have wr...
