Metra 99-7604T - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; NOWLEDGE IS

Dash Disassembly - INFINITI G35 2003-2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2,3 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . ...

Page 3 - isconnect the negative battery ter-

99-7604 DASH DISASSEMBLY INFINITI G35 2003-2004 1 D isconnect the negative battery ter- minal to prevent an accidental shortcircuit. 1 Unclip the collar below the shift knoband slide down. Using a small screw-driver or hook tool remove the springclip to release and remove the shiftknob. (Figure A) 2...

Page 5 - Continue to kit preparation.

99-7604 DASH DISASSEMBLY INFINITI G35 2003-2004 3 Remove (2) Phillips screws securingthe pocket to the radio/climate con-trol panel and remove pocket. (Retainpocket for use during kit assembly.) 16 Use (2) small flat blade screwdriversto gently pry the vents from radio/cli-mate control panel to remo...

Page 6 - KIT PREPARATION; Continue to kit assembly

4 99-7604 KIT PREPARATION B C A KIT PREPARATION Attach the vents into the radio housingin the same location as the factorypanel. (Figure A) 1 Secure the factory pocket removed instep 16 of the dash disassembly intothe radio housing using the factoryhardware. (Figure B) 2 Continue to kit assembly . *...

Page 7 - DIN RADIO PROVISION WITH POCKET; Continue to final assembly

5 99-7604 KIT ASSEMBLY B C A DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into thecage until it snaps into place. (Figure B) 2 Continue to final assembly . * Note: Refer also to ...

Page 8 - ISO MOUNT RADIO PROVISION WITH POCKET

6 99-7604 KIT ASSEMBLY B A ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the radiowith the screws supplied with theradio. (Figure A) 1 Slide the radio into the radio housinguntil it snaps into place. (Figure B) 2 Snap the ISO trim plate onto the frontof the Radio Housing. (Figure B...

Page 9 - DOUBLE DIN RADIO PROVISION

7 99-7604 KIT ASSEMBLY B C A DOUBLE DIN RADIO PROVISION Snap the Double DIN brackets to theinside edge of the radio housing. (Figure B) 2 1 Slide the Double DIN radio into thebracket/trim plate assembly andsecure the radio to the assembly usingthe screws supplied with the radio. (Figure C) 3 Snap th...

Page 10 - STACKED ISO UNITS PROVISION

8 99-7604 KIT ASSEMBLY B C A STACKED ISO UNITS PROVISION Snap the Double DIN brackets to theinside edge of the radio housing. (Figure B) 2 Slide the stacked ISO units into thebracket/radio housing assembly andsecure the units to the kit using thescrews supplied with the units. (Figure C) 3 Snap the ...

Page 11 - FINAL ASSEMBLY; B) Twist ends together; FINAL WIRING CONNECTIONS; METRA / EIA WIRING CODE; When a Black wire is not present, ground radio to vehicle chassis.

99-7604 FINAL ASSEMBLY FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape A B C D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of an...