Metra 99-7503 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Electronic Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Manual Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Kit Assembly . . . . . . . . . . . . . . . . ...

Page 3 - DASH DISASSEMBLY; Electronic Climate Control

99-7503 1 Disconnect the negative battery terminal to prevent an accidentalshort circuit. 1 Unscrew the shift knob counterclockwise to remove. (Figure A) 2 2003-2004 MAZDA 6 Unclip and remove the cupholder/parking brake cover andshifter cover as one unit. (Figure B) 3 Remove (2) Phillips screws from...

Page 5 - Manual Climate Control

3 Disconnect the negative battery terminal to prevent an accidentalshort circuit. 1 Unscrew the shift knob counterclockwise to remove. (Figure A) 2 Remove (2) Phillips screws from thebottom of the radio/climate controlpanel. (Figure C) 4 Pull the climate control knobs offand remove (2) Phillips scre...

Page 6 - Notice how they are posi-

Open glove box, squeeze sidestogether and let open fully thenremove (1) 10 MM bolt from the sideof the radio bracket. (Figure E) 6 INSIDE GLOVE BOX E 4 99-7503 DASH DISASSEMBLY 2003-2004 MAZDA 6 Manual Climate Control Unsnap and remove radio/climatecontrol panel including climate con-trol vents at t...

Page 8 - KIT ASSEMBLY; The 16 position to 16 position

6 99-7503 2003-2004 MAZDA 6 Electronic Climate Control KIT ASSEMBLY A REAR VIEW OF ELECTRONIC CLIMATE CONTROL B D C Clip the climate control knob outertrim ring panel into the 99-7503 housing. (Figure A) Align the screw holes in the climatecontrol and the radio housing panelthen push the climate con...

Page 9 - ASSEMBLED; You may have to push down

Manual Climate Control 99-7503 KIT ASSEMBLY 2003-2004 MAZDA 6 7 A ASSEMBLED B INSTALLED C D E Put the climate control knob outertrim panel and the backlight disper-sion bar together and clip into theradio housing panel as one unit. Note: You may have to push down slightly on the middle of the unit t...

Page 11 - FELT TAPE APPLICATION; Apply To

9 FELT TAPE APPLICATION 99-7503 Apply To Rear Of Both Sides Note: Due to differences in factory tolerances you may need to apply the provided felt tape to theedge of the 99-7503 radio housing to relieve backlight bleed through. 1. Looking at edge of radio housing apply felt tape to inner edge (towar...

Page 12 - DISPLAY CUSTOMIZATION

10 DISPLAY CUSTOMIZATION 99-7503 CLOC K SET DIMM ER AMB 1. Press and hold the Clock button in the factory display until “Set Text” is displayed, then release the button. Settings will begin with the first character location. Use the Set button to select the desired character then press the AMB butto...

Page 13 - FINAL WIRING and ASSEMBLY; FINAL ASSEMBLY; When Black a wire is not present, ground radio to vehicle chassis.; METRA / EIA WIRING CODE

11 FINAL WIRING and ASSEMBLY 1 2 3 4 5 6 Locate the factory wiring harness in the dash. Use the supplied wire harnesses and make the connection as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) A A) Strip wire ends back 1/2" B) Twist ...

Page 14 - NOTES