Lexmark MS410D - Manuals

1 2 3 4 5 1 Right side 305 mm (12 in.) 2 Front 510 mm (20 in.) 3 Left side 205 mm (8 in.) 4 Rear 205 mm (8 in.) 5 Top 305 mm (12 in.) Printer configurations CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all other trays closed until needed. You...

Using the printer control panel 9 3 1 2 4 5 6 7 8 Use the To 1 Menus button Open the menus. Notes: • The menus are available only when the printer is in the Ready state. • Pressing the button while navigating within the menus returns the printer control panelto the top ‑ level menu screen. 2 Display...

Use the To 9 Indicator light Determine the status of the printer. Understanding the colors of the Sleep button and indicatorlights The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition. Indicator light color and its correspondi...

Notes: – An IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. – If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Open a Web browser, and then type the printer IP address in the address field. 3 Press Enter . The Em...

Additional printer setup Installing internal options CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electrical outlet before continui...

2 1 1 Memory card connector 2 Option card connector Installing a memory card CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electrica...

Installing an optional card CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electrical outlet before continuing. If you have other dev...

Installing hardware options Installing optional trays CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electrical outlet before continu...

7 Align the printer with the tray, and then slowly lower the printer into place. 8 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer. 1 2 Note: When the printer software and any hardware options are installed, it may be necessary to ma...

• The appropriate Ethernet cable with the Ethernet port Warning—Potential Damage: Do not touch the USB cable, any network adapter, or the printer in the area shown while actively printing. Loss of data or a malfunction can occur. 1 2 3 4 5 6 7 Use the To 1 USB port * Attach an optional wireless netw...

1 Obtain a copy of the software installer package. • From the Software and Documentation CD that came with your printer. • From our Web site:Go to http://support.lexmark.com , and then navigate to: SUPPORT & DOWNLOAD > select your printer > select your operating system 2 Double ‑ click the...

For Windows users 1 Open the printers folder. In Windows 8 From the Search charm, type run , and then navigate to: Apps list > Run > type control printers > OK In Windows 7 or earlier a Click or click Start , and then click Run . b In the Start Search or Run dialog, type control printers . ...

Networking Notes: • Purchase a MarkNet TM N8352 wireless network adapter first before setting up the printer on a wireless network. For information on installing the wireless network adapter, see the instruction sheet that came with theadapter. • A Service Set Identifier (SSID) is a name assigned to...

– This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to: System Preferences > Print & Fax b Click + , and then navigate to: AppleTalk > select your printer > Add Preparing to set up the printer on a wireless network Notes: • Make sure your wireless ...

– To find the WPA/WPA2 preshared key/passphrase for the wireless network, see the documentation that camewith the access point, see the Web page associated with the access point, or consult your system supportperson. Connecting the printer to a wireless network using Wi ‑ Fi Protected Setup Before c...

Installing the Wireless Setup Utility 1 Go to the Lexmark Web site at http://support.lexmark.com . 2 Download the latest Wireless Setup Utility. 3 Double ‑ click the downloaded software installer package. 4 Follow the instructions on the computer screen. Launching the Wireless Setup Utility Notes: •...

• Make sure a wireless network adapter installed in your printer is attached and working properly. 1 From the Finder, navigate to: Applications > select your printer folder 2 Double ‑ click Wireless Setup Assistant , and then follow the instructions on the computer screen. Note: If you encounter ...

Printing a network setup page If the printer is connected to a network, then print a network setup page to verify the network connection. This pagealso provides important information that aids network printing configuration. 1 From the printer control panel, navigate to: > Reports > > Netwo...

Loading paper and specialty media The selection and handling of paper and specialty media can affect how reliably documents print. For more information,see “Avoiding jams” on page 105 and “Storing paper” on page 48. Setting the paper size and type 1 From the printer control panel, navigate to: > ...

Loading the multipurpose feeder Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock,transparencies, paper labels, and envelopes. You can also use it for single ‑ page print jobs on letterhead. 1 Open the multipurpose feeder. 1 2 a Pull ...

• Load letterhead faceup with the top edge entering the printer first. For two ‑ sided (duplex) printing, load letterhead facedown with the bottom edge entering the printer first. • Load envelopes with the flap on the left side facedown. Warning—Potential Damage: Never use envelopes with stamps, cla...

• If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Paper Menu . 3 Change the tray settings to specify the paper size and type for the tray. • To link trays, make sure the paper size and type for the tray match with that of the other t...

• If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Paper Menu > Custom Types . 3 Select a custom paper type name, and then select a custom paper type. Note: Plain Paper is the factory default paper type for all user ‑ defined custo...

Paper and specialty media guide Additional information for printing on specialty media may be found in the Card Stock and Label Guide available at http://support.lexmark.com . Paper guidelines Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a...

Grain direction Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long , running the length of the paper, or grain short , running the width of the paper. For 60–90 ‑ g/m 2 (16–24 ‑ lb) bond paper, grain long paper is recommended. Fiber content Most high ‑ ...

• Avoid papers with rough or heavily textured surfaces. Use papers printed with heat ‑ resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected bythe res...

Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained.However, the following paper choice guidelines will help alleviate the environmental impact of printing: 1 Minimize paper consumption. 2 Be selective about the origin of wood fiber...

• Do not use labels with exposed adhesive. • Do not print within 1 mm (0.04 inch) of the edge of the label, of the perforations, or between die ‑ cuts of the label. • Make sure the adhesive backing does not reach to the edge of the sheet. Zone coating of the adhesive should beat least 1 mm (0.04 inc...

Supported paper sizes, types, and weights For information on card stock and labels, see the Card Stock & Label Guide . Supported paper sizes Paper size Standard tray Optional 250 ‑ or 550 ‑ sheet tray Multipurpose feeder Duplex mode A4 210 x 297 mm (8.3 x 11.7 in.) A5 148 x 210 mm (5.8 x 8.3 in....

Paper size Standard tray Optional 250 ‑ or 550 ‑ sheet tray Multipurpose feeder Duplex mode 10 Envelope 105 x 241 mm (4.1 x 9.5 in.) X X X DL Envelope 110 x 220 mm (4.3 x 8.7 in.) X X X C5 Envelope 162 x 229 mm (6.4 x 9 in.) X X X B5 Envelope 176 x 250 mm (6.9 x 9.8 in.) X X X Other Envelope 229 x 3...

Printing This chapter covers printing, printer reports, and job cancelation. Selection and handling of paper and specialty mediacan affect how reliably documents print. For more information, see “Avoiding jams” on page 105 and “Storing paper”on page 48. Printing a document Printing a document 1 From...

• If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Print Settings > Quality Menu > Toner Darkness . 3 Adjust the toner darkness setting. 4 Click Submit . Using the printer settings on the computer Depending on your operating sys...

Understanding the printer menus Menus list Paper Menu Reports Network/Ports 3 Default Source Paper Size/TypeConfigure MP Substitute Size Paper Texture Paper Weight Paper Loading Custom Types Universal Setup Menu Settings Page Device Statistics Network Setup Page 1 Profiles ListPrint Fonts Print Dire...

Configure MP menu Use To Configure MP CassetteManualFirst Determine when the printer selects paper from the multipurpose feeder. Notes: • Cassette is the factory default setting. Cassette configures themultipurpose feeder as the default paper source. • Manual sets the multipurpose feeder only for ma...

Paper Weight menu Use To Plain Weight LightNormalHeavy Specify the relative weight of the plain paper loaded. Note: Normal is the factory default setting. Card Stock Weight LightNormalHeavy Specify the relative weight of the card stock loaded. Note: Normal is the factory default setting. Transparenc...

Use To Colored Weight LightNormalHeavy Specify the relative weight of the colored paper loaded. Note: Normal is the factory default setting. Light Weight Light Specify that the weight of the paper loaded is light. Heavy Weight Heavy Specify that the weight of the paper loaded is heavy. Cotton/Rough ...

Use To Light Loading DuplexOff Determine and set two ‑ sided printing for all print jobs that specify Light as the paper type. Heavy Loading DuplexOff Determine and set two ‑ sided printing for all print jobs that specify Heavy as the paper type. Custom [x] Loading DuplexOff Determine and set two ‑ ...

Universal Setup menu Use To Units of Measure InchesMillimeters Identify the units of measure. Notes: • Inches is the US factory default setting. • Millimeters is the international factory default setting. Portrait Width 3–8.5 inches76–216 mm Set the portrait width. Notes: • If the width exceeds the ...

Use To Network Setup Page Print a report containing information about the network printer settings, such asthe TCP/IP address information. Note: This menu item appears only in network printers or in printers connected to print servers. Profiles List Print a list of profiles stored in the printer. No...

Network Card menu To access the menu, navigate to either of the following: • Network/Ports > Standard Network > Standard Network Setup > Network Card • Network/Ports > Network [x] > Network [x] Setup > Network Card Use To View Card Status ConnectedDisconnected View the connection s...

Use To Enable AutoIP YesNo Specify the Zero Configuration Networking setting. Note: Yes is the factory default setting. Enable FTP/TFTP YesNo Enable the built-in FTP server, which lets you send files to the printer using File TransferProtocol. Note: Yes is the factory default setting. Enable HTTP Se...

Use To Set Hostname * Set the host name. Note: The host name is limited to 15 characters, and accepts US ‑ ASCII, alphanumeric characters and hyphen only. View Address * View the current IPv6 addresses. View Router Address * View the current router address. Enable DHCPv6 OnOff Enable DHCPv6 in the p...

Use To Activate YesNo Enable or disable AppleTalk support. Note: Yes is the factory default setting. View Name Show the assigned AppleTalk name. Note: The name can be changed only from the Embedded Web Server. View Address Show the assigned AppleTalk address. Note: The address can be changed only fr...

Use To USB Buffer DisabledAuto3K to [maximum size allowed] Set the size of the USB input buffer. Notes: • Auto is the factory default setting. • Disabled turns off job buffering. • The USB buffer size value can be changed in 1-KB increments. • The maximum size allowed depends on the amount of memory...

Use To Use SSL DisabledNegotiateRequired Set the printer to use SSL for increased security when connecting to theSMTP server. Notes: • Disabled is the factory default setting. • When the Negotiate setting is used, the SMTP server determines ifSSL will be used. SMTP Server Authentication No authentic...

Use To Configure Log Enable Audit YesNo Enable Remote Syslog NoYes Remote Syslog Facility 0–23 Severity of events to log 0–7 Specify how and whether or not audit logs are created. Notes: • Enable Audit determines if events are recorded in the secure audit log andremote syslog. No is the factory defa...

Settings menu General Settings menu Use To Display Language EnglishFrancaisDeutschItalianoEspanolDanskNorskNederlandsSvenskaPortugueseSuomiRussianPolskiGreekMagyarTurkceCeskySimplified ChineseTraditional ChineseKoreanJapanese Set the language of the text appearing on the printer display. Note: Not a...

Use To Press Sleep Button Do nothingSleepHibernate Determine how the printer, while in idle state, reacts to a shortpress of the Sleep button. Note: Sleep is the factory default setting. Press and Hold Sleep Button Do nothingSleepHibernate Determine how the printer, while in idle state, reacts to a ...

Finishing menu Use To Sides (Duplex) 1 sided2 sided Specify whether two ‑ sided (duplex) printing is set as the default for all print jobs. Notes: • “1 sided” is the factory default setting. • You can set two ‑ sided printing from the software program. For Windows users: 1 Click File > Print . 2 ...

Use To Paper Saver Off2 ‑ Up 3 ‑ Up 4 ‑ Up 6 ‑ Up 9 ‑ Up 12 ‑ Up 16 ‑ Up Print multiple ‑ page images on one side of a paper. Notes: • Off is the factory default setting. • The number selected is the number of page images that will print per side. Paper Saver Ordering HorizontalReverse HorizontalRev...

Use To Enhance Fine Lines OnOff Enable a print mode preferable for files such as architectural drawings, maps, electricalcircuit diagrams, and flow charts. Notes: • Off is the factory default setting. • You can set this option from the printer software. For Windows users, click File > Print , and...

Saving money and the environment Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impacton the environment. We design with the environment in mind, engineer our packaging to reduce materials, and providecollection and recycling programs. ...

Avoid paper jams Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 105. Saving energy Using Eco ‑ Mode Use Eco ‑ Mode to quickly select one or more ways to reduce your printer's environmental impact. 1 From the printer control panel, navigat...

3 From the Press Sleep Button or Press and Hold Sleep Button drop ‑ down menu, select Hibernate . 4 Click Submit . Note: If the printer is in Hibernate mode, the Embedded Web Server is disabled. Using the printer control panel 1 From the printer control panel, navigate to: > Settings > > Ge...

Setting Hibernate Timeout Hibernate Timeout lets you set the amount of time the printer waits after a print job is processed before it goes into areduced power state. Using the Embedded Web Server 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • Print a netwo...

Recycling Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information,see: • The Notices chapter • The Environmental Sustainability section of the Lexmark Web site at www.lexmark.com/environment • The Lexmark recycling program at www.lexmark.com...

Securing the printer Using the security lock feature The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers inthe location shown to secure the printer in place. Statement of Volatility Your printer contains various types of memory that can ...

Erasing volatile memory The volatile memory (RAM) installed in your printer requires a power source to retain information. To erase the buffereddata, simply turn off the printer. Erasing non ‑ volatile memory 1 Turn off the printer. 2 From the printer control panel, hold down and the right arrow but...

Maintaining the printer Warning—Potential Damage: Failure to maintain optimum printer performance, or to replace parts and supplies, may cause damage to your printer. Cleaning the printer Cleaning the printer Note: You may need to perform this task after every few months. Warning—Potential Damage: D...

Using the printer control panel From the printer control panel, navigate to: > Reports > > Device Statistics > Note: You can view the status of parts and supplies in the “Supply Information” section of the pages printed. Estimated number of remaining pages The estimated number of remaini...

Item Regular cartridge Extra High Yield Toner Cartridge 500XA 2 Ultra High Yield Toner Cartridge 500UA 3 1 This cartridge is supported only in MS310d and MS310dn printer models. 2 This cartridge is supported only in MS410d and MS410dn printer models. 3 This cartridge is supported only in MS510dn, MS...

Replacing supplies Replacing the toner cartridge 1 Press the button on the right side of the printer, and then open the front door. 2 1 2 Pull the toner cartridge out using the handle. 3 Unpack the toner cartridge, and then remove all packing materials. 4 Shake the new cartridge to redistribute the ...

6 Close the front door. Replacing the imaging unit 1 Press the button on the right side of the printer, and then open the front door. 2 1 2 Pull the toner cartridge out using the handle. Maintaining the printer 97

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrowson the side rails inside the printer. 7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side railsinside the printer. ...

• If an optional tray is installed, then remove it from the printer. To remove the optional tray, slide the latch on theright side of the tray toward the front of the tray until it clicks into place. • Use the handholds located on both sides of the printer to lift it. • Make sure your fingers are no...

Managing the printer Finding advanced networking and administrator information This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced systemsupport tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server Adminis...

Notes: • Selectable alerts can be set on the toner cartridge and imaging unit. • All selectable alerts can be set for nearly low, low, and very low supply conditions. Not all selectable alerts canbe set for the end ‑ of ‑ life supply condition. E ‑ mail selectable alert is available for all supply c...

Clearing jams Carefully select paper and specialty media and load them properly to avoid most jams. For more information, see“Avoiding jams” on page 105. If jams occur, then follow the steps outlined in this chapter. Note: Jam recovery is set to Auto by default. The printer reprints jammed pages unl...

• Do not slide the paper into the tray. Load paper as shown in the illustration. • Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing tightlyagainst the paper or envelopes. • Push the tray firmly into the printer after loading paper. Use recommen...

Troubleshooting Understanding the printer messages Cartridge, imaging unit mismatch [41.xy] 1 Check if both the toner cartridge and imaging unit are MICR (Magnetic Ink Character Recognition) or non-MICR supplies. Note: For a list of supported supplies, see the “Ordering supplies” section of the User...

If necessary, press on the printer control panel to clear the message and continue printing. Imaging unit low [84.xy] You may need to order an imaging unit. If necessary, press on the printer control panel to clear the message and continue printing. Change [paper source] to [custom type name]. Load ...

Load MP feeder with [paper size] [orientation] Try one or more of the following: • Load the feeder with the correct size of paper. • From the printer control panel, press to clear the message and continue printing. Note: If no paper is loaded in the feeder, then the printer manually overrides the re...

Printer and toner cartridge regions Region number Region 0 Global 1 United States, Canada 2 European Economic Area (EEA), Switzerland 3 Asia Pacific, Australia, New Zealand 4 Latin America 5 Africa, Middle East, rest of Europe 9 Invalid Notes: • The x and y values represent . xy in the code that app...

Too many trays. Remove some. [58] 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the extra trays. 4 Connect the power cord to the electrical outlet. 5 Turn the printer back on. Flash memory unformatted [53] Try one or more of the following: • From the printer co...

Action Yes No Step 11 Check the installed printer driver. Is the correct printer driver installed? Go to step 12. Install the correctprinter driver. Step 12 Turn off the printer, then wait for about 10 seconds, and then turn theprinter back on. Is the printer working? The problem is solved. Contact ...

Action Yes No Step 3 Print a menu settings page, and then check to see if the internal option islisted in the Installed Features list. Is the internal option listed in the menu settings page? Go to step 4. Reinstall the internaloption. Step 4 a Check if the internal option is selected. It may be nec...

Action Yes No Step 4 Check if the tray is available in the printer driver. Note: If necessary, manually add the tray in the printer driver to make it available for print jobs. For more information, see “Updating availableoptions in the printer driver” on page 22. Is the tray available in the printer...

Paper feed problems Paper frequently jams Action Yes No Step 1 a Pull out the tray, and then do one or more of the following: • Make sure paper lies flat in the tray. • Check if the paper size indicators on the paper guides are alignedwith the paper size indicators on the tray. • Check if the paper ...

Jammed pages are not reprinted Action Yes No a Turn on jam recovery. 1 From the printer control panel, navigate to: > Settings > > General Settings > > Print Recovery > > Jam Recovery > 2 Press the arrow buttons until On or Auto appears, and then press . b Resend the pages th...

Action Yes No Step 4 a Check if the ports (USB, serial, or Ethernet) are working and if thecables are securely connected to the computer and the printer. Note: For more information, see the setup documentation that came with the printer. b Resend the print job. Do the jobs print? The problem is solv...

Print job takes longer than expected Action Yes No Step 1 Reduce the number and size of fonts, the number and complexity ofimages, and the number of pages in the print job, and then resend theprint job. Does the print job still take long? Go to step 2. The problem is solved. Step 2 Disable the Page ...

Action Yes No Step 3 a Depending on your operating system, open Printing Preferences orthe Print dialog, and then specify the paper type. b Resend the print job. Did the job print from the correct tray or on the correct paper? The problem is solved. Go to step 4. Step 4 a Check if the trays are not ...

Large jobs do not collate Action Yes No Step 1 a From the Finishing menu on the printer control panel, set Collate to(1,2,3) (1,2,3). b Resend the print job. Did the job print and collate correctly? The problem is solved. Go to step 2. Step 2 a From the printer software, set Collate to (1,2,3) (1,2,...

Print quality problems Characters have jagged or uneven edges Action Yes No Step 1 a Print a font sample list to check if the fonts you are using are supportedby the printer. 1 From the printer control panel, navigate to: > Reports > > Print Fonts > 2 Press the arrow buttons until PCL Fo...

Action Yes No Step 1 a Check if there is packing material left on the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imagingunit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more tha...

Action Yes No Step 1 a Move the width and length guides in the tray to the correct positionsfor the paper loaded. b Resend the print job. Is the page or image clipped? Go to step 2. The problem is solved. Step 2 From the printer control panel, set the paper size and type in the Papermenu to match th...

Action Yes No Step 1 Load paper with the correct paper type and weight in the tray. Is paper with the correct paper type and weight loaded in the tray? Go to step 2. Load paper with thecorrect paper type andweight in the tray. Step 2 From the printer control panel, set the paper type and weight in t...

Action Yes No Step 2 Reinstall the imaging unit and the toner cartridge. a Remove the toner cartridge. b Remove the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to lightcan cause print quality problems. c Install t...

Action Yes No Step 3 a Depending on your operating system, specify the paper size fromPrinting Preferences or from the Print dialog. b Resend the print job. Are the margins correct? The problem is solved. Contact customer support . Paper curl Action Yes No Step 1 Move the width and length guides in ...

Print irregularities ) ) ABCDE ABCDE ABCDE Leading edge Trailing edge Action Yes No Step 1 a Move the width and length guides in the tray to the correct positionsfor the size of the paper loaded in the tray. b Resend the print job. Do print irregularities still appear? Go to step 2. The problem is s...

Repeating defects appear on prints Action Yes No Step 1 Measure the distance between the defects. Check for a distance between the defects that equals: • 97 mm (3.82 in.) • 47 mm (1.85 in.) • 38 mm (1.5 in.) Is the distance between defects equal to one of the listed measurements? Go to step 2. 1 Che...

Print is too light Action Yes No Step 1 a From the Quality menu on the printer control panel, increase the tonerdarkness. Note: 8 is the factory default setting. b Resend the print job. Is the print still too light? Go to step 2. The problem is solved. Step 2 From the printer control panel, set the ...

Action Yes No Step 6 a Redistribute the toner in the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print qu...

Printer is printing solid black pages Action Yes No Step 1 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print quality probl...

Streaked horizontal lines appear on prints ABCDEABCDEABCDE Action Yes No Step 1 a Depending on your operating system, specify the tray or feeder fromPrinting Preferences or the Print dialog. b Resend the print job. Do streaked horizontal lines appear on prints? Go to step 2. The problem is solved. S...

Streaked vertical lines appear on prints ABCDEABCDEABCDE Leading edge Trailing edge Action Yes No Step 1 a Depending on your operating system, specify the paper type, texture,and weight from Printing Preferences or from the Print dialog. b Resend the print job. Do streaked vertical lines appear on p...

Action Yes No Step 5 Replace the imaging unit, and then resend the print job. Do streaked vertical lines appear on prints? Contact customer support at http://support.lexmark.com or your service representative. The problem is solved. Horizontal voids appear on prints Leading edge Trailing edge Action...

Vertical voids appear on prints Leading edge Trailing edge Action Yes No Step 1 a Make sure your software program is using a correct fill pattern. b Resend the print job. Do vertical voids appear on prints? Go to step 2. The problem is solved. Step 2 a From the printer control panel, set the paper t...

Toner specks appear on prints Action Yes No Replace the imaging unit, and then resend the print job. Do toner specks appear on prints? Contact customer support . The problem is solved. Toner rubs off Leading edge Trailing edge ABC DEF Action Yes No Step 1 From the Paper menu on the printer control p...

Embedded Web Server does not open Action Yes No Step 1 a Turn on the printer. b Open a Web browser, and then type the printer IP address. c Press Enter . Does the Embedded Web Server open? The problem is solved. Go to step 2. Step 2 Make sure the printer IP address is correct. a View the printer IP ...

Action Yes No Step 5 Temporarily disable the Web proxy servers. Proxy servers may block or restrict you from accessing certain Websites including the Embedded Web Server. Does the Embedded Web Server open? The problem is solved. Contact your system support person. Contacting customer support When yo...

Notices Product information Product name: Lexmark MS410d, MS410dn Machine type: 4514 Model(s): 420, 430 Edition notice September 2012 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “A...

Trademarks Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered inthe United States and/or other countries. Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries. PCL® is a registered trademark of the H...

Static sensitivity notice This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching themetal frame of the printer. ENERGY STAR Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to complywith...

DANGER - Invisible laser radiation when cartridges are removed and interlock defeated. Avoid exposure to laser beam.PERIGO - Radiação a laser invisível será liberada se os cartuchos forem removidos e o lacre rompido. Evite a exposição aos feixes de laser. Opasnost - Nevidljivo lasersko zra č enje ka...

Sleep Mode This product is designed with an energy-saving mode called Sleep Mode . The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this productis not used for a specified period of time, called the Sleep M...

L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettreaucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous auCode de sécurité 6 que vous pouvez consulter sur le site Web de Santé ...

Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo č ili direktive 1999/5/ES. Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentligaegenskapskrav och övriga relevanta b...

This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for anyclaim by you based on a third party claim. This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and itsSuppliers' and Rem...

Index A accessing the controller board 14Active NIC menu 65adjusting Sleep mode 87adjusting toner darkness 52administrator settings Embedded Web Server 101 AppleTalk menu 69assigning custom paper types 42attaching cables 20available internal options 14avoiding jams 48avoiding paper jams 105 B Bin fu...