Leica Leica Racer 100- Manuals

3 Safety Instructions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ The person in charge of the instrument has the following duties:• To understand the safety instructions on the product and the instructions in the User Manual. • To be familiar with local safety regulatio...

4 Safety Instructions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ  WARNING: The Leica Racer conforms to the most stringent requirements of the relevant standards and regula-tions. Yet, the possibility of it causing interference in other devices cannot be totally exclud...

5 Start-up Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Start-up Inserting/replacing batteries See figure { A } 1 Remove battery compartment lid and attach handstrap. 2 Insert batteries, observing correct polarity. 3 Close the battery compartment again. Replace the batte...

6 Menu functions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Display See figure { F } 1 Laser active 2 Reference (front) 3 Reference (rear) 4 Reference (corner stop) 5 Measuring with the tripod 6 Stake out function 7 Single Pythagorean measurement 8 Double Pythagorean m...

7 Menu functions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Setting the unit for distance measurements The following units can be set: Setting the unit for tilt measurements The following units can be set for tilt measurements: Beep ( ) You can switch the beep on or of...

8 Operation Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ A reset returns the following values to their factory settings: • Reference (rear) • Display illumination (ON) • Beep (ON) • Unit (m(mm)) • Stack and memory are erased ) All customised settings and stored values ar...

9 Measuring Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Measuring Single distance measurement Press to activate the laser. Press again to trigger the distance measurement. The result is displayed immediately. Minimum/maximum measurement This function allows the user to ...

10 Functions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Volume Press this button twice . The symbol appears in the display. Press this button to take the first length measurement (e.g. length). Press this button to take the second length measurement (e.g. width). Press...

11 Functions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Stake out function Two different distances (a and b) can be entered into the instrument and can then be used to mark off defined measured lengths, e.g. in the construction of wooden frames. See figure { L }. Enter...

13 Functions Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Indirect measurement - determining a chain value using 3 measurements See figure { O } e.g. determining the height between point 1 and point 2 using three target points. Press this button three times ; the display...

14 Appendix Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Timer (self-triggering) Press this button to set a 5-second time delay. or Press and hold down this button until the desired time delay is reached (max. 60 seconds). Once the key is released the remaining seconds u...

15 Appendix Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Technical data * maximum deviation occurs under unfavourable conditions such as bright sunlight or when measuring to poorly reflecting or very rough surfaces. Measuring accuracy between 10 m and 30 m may deteriorat...

16 Appendix Leica Racer 100 784117 en EN D F I E P NL DK S N FIN J CN ROK PL H RUS CZ Measuring conditions Measuring range The range is limited to 100 m. At night or dusk and if the target is in shadow the measuring range without target plate is increased. Use a target plate to increase the measurem...