Leica Leica DISTO plus - Manual- Manuals

Page 2 - User Manual; English; Contents; Leica DISTOTM plus hand-held laser meter; Product identification; Keypad

1 Keypad Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja User Manual Version 1.0 English The Safety Instructions (738266) in a separate brochure form a part of this User Manual. Carefully read the Safety Instructions and the User Manual before using this product. Contents Keypad .......................

Page 4 - How to Use the Instrument; Inserting / replacing the batteries; Function level; Leica DISTOTM plus switching ON/OFF

3 How to Use the Instrument Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja How to Use the Instrument Inserting / replacing the batteries 1 Depress the locking clip and slide end piece to the right. D5-Z3 2 Remove battery cover. Replace batteries. Appears on the display if battery voltage is too low...

Page 5 - Measuring; Distance measurement; Measuring from flat planes; Laser in continous operation

4 1st Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Possible settings D5-Z4 front tripod rear ) At the back of the instrument is a 1/4" camera thread for the tripod. ) Settings remain valid until the reference level is changed or the instrument is automatically or manually switc...

Page 6 - Calculations; Area; Volume

5 1st Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Time delay release Instrument must be in Pointing Mode. Press and hold until desired time delay has been reached (max. 60 seconds).appears on the display. Once the key is released, the remaining seconds (e.g. 59, 58, 57...) are dis...

Page 7 - st Function level

6 1st Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Confirm selection, reset to Normal Mode. ) "Clear Entry" may also be used (e.g. to cancel a selection). Selecting units (menu) Selectable units: Measure with offset (menu) D5-Z10 Call up menu point. blinks on the display. W...

Page 9 - Partial heights, partial distances; Multiplication; Doubling a measured value

8 1st Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Determine maximum dimension, e.g. to determine the (room) diagonal. Press until appears on the display. Move the Leica DISTO™ plus a large amount around the target point. Activate continuous measurement with a brief press. Slowly r...

Page 10 - Detemination with 3 points

9 1st Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja ) With each of the distance measurements you can use:• a simple distance measurement, • a value from stack/ mermory or • a measurement with time delay release. ) For short distances, a good base behind the instrument is sufficient ...

Page 11 - nd Function level; Switching on the BLUETOOTH

10 2nd Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Move the Leica DISTO™ plus a large amount around the ideal measurement point. Stop of continuous measurement. Value is accepted and and on the display "3 ---" starts blinking. Aim at the lower point (3). Trigger measuremen...

Page 12 - Switching off the BLUETOOTH

11 2nd Function level Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Switching off the BLUETOOTH ® ) Before switching off the BLUETOOTH ® , always change to the first function level Press briefly. BLUETOOTH ® is switched off,when this icon is no longer visible ) If still in the second function leve...

Page 13 - During data transfer; User Information; Range; Rough surfaces

12 User Information Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Press briefly to confirm that the correct line was drawn. The line is then drawn thicker with the measurement dispayed.Press briefly to clear a wrong line. . Is the measurement is still displayed in the Leica DISTO™ plus, it can be ...

Page 14 - Inclined, round surfaces; In the field; Technical Data

13 Technical Data Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja Wet, smooth or high-gloss surfaces 1 Aiming at a "obtuse" angle deflects the laser beam. The Leica DISTO™ plus may receive a signal that is too weak (error message 255). 2 If aiming at a right angle, the Leica DISTO™ plus may ...

Page 15 - Message Codes; Error message

14 Message Codes Leica DISTO™ plus 1.0.0 GB de GB fr it es nl ja * Maximum deviation occurs under unfavorable condi-tions, such as in bright sunlight or when measuring to inadequately reflecting surfaces. For distances over 30m-without using a target plate- themaximum devia-tion may increase by ±0.1...

Page 16 - Leica Geosystems AG

Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) www.leica-geosystems.com Pat. No. • US 5,815,251 • US 5,949,531 • US 6,336,277 • US 6,463,393 • EP 0738 899 • EP 0932 835 Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the Interna...