Jacuzzi J - 355 - Manuals

1 J-300 series J-300 Series 1.0 Important spa owner Information Your Jacuzzi ® J-300 Series spa is constructed to the highest standards and is capable of providing many years of trouble-free use. However, because heat retentive materials are utilized to insulate the spa for efficient operation, an u...

2 J-300 Series 3.0 Important safety Instructions for all spa owners reaD anD Follow all InsTruCTIons CareFullY! This spa was manufactured to meet the standards and specifications outlined in the “Virginia Graeme Baker Pool and Spa Safety Act” (VGB Safety Act). When installing and using this spa, bas...

3 J-300 series J-300 Series unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5m) of the unit. Never permit any electrical appliance, such as a light, telephone, radio, • television, etc. within 5 feet (1.5m) of a spa unless such ap...

5 J-300 series J-300 Series hot tub safety literature To ensure you have a safe and enjoyable hot tub experience, learn all you can about hot tub safety and emergency procedures. Especially useful are the brochures listed below: Children Aren’t Waterproof • Pool and Spa Emergency Procedures For Infa...

6 J-300 Series 3.1 entrapment risk The Consumer Products Safety Commission/USA has reported that users of pools and spas have become entrapped (stuck) to drain and/or suction fittings causing death, drowning, or serious injury (see diagram below). This spa was manufactured to meet the standards and ...

7 J-300 series J-300 Series 3. ! DanGer: rIsK oF severe InJurY or DrownInG! Body entrapment: May occur when part of the torso becomes entrapped, inserted or sucked into a suction or outlet opening. Never allow children to play or get near the suction fittings, suction • covers, filter, filter lid or...

9 J-300 series J-300 Series 4.0 Choosing a location ImporTanT: Because of the combined weight of the spa, water and users, it is extremely important that the base upon which the spa rests be smooth, flat, level and capable of uniformly supporting this weight, without shifting or settling, for the en...

12 J-300 Series 5.0 General electrical safety Instructions Your new Jacuzzi® spa is equipped with a “state-of-the-art” equipment system. It contains the most advanced safety and self-protective equipment in the industry. Nonetheless, this spa must be installed properly to insure dependable usage. Pl...

13 J-300 series J-300 Series north american J-335, J-345, J-355, J-365 and J-375 Models (60 hz) 240V/40A* 240V/50A** 240V/60A*** Circuit Breaker (2-Pole): 40A 50A 60A Number of Wires: 3 3 3 Frequency: 60 Hz 60 Hz 60 Hz Current Draw: 26A 36A 45A * In 40A configuration, the heater will not operate whi...

14 J-300 Series export J-335, J-345, J-355, J-365 and J-375 Models (50 hz) 230V/20A* 230V/30A** 230V/40A*** Circuit Breaker: 20A 30A 40A Number of Wires: 3 3 3 Frequency: 50 Hz 50 Hz 50 Hz Current Draw: 15A 23A 29A * In 20A configuration, the heater will not operate while either jets pump is running...

15 J-300 series J-300 Series 7.0 electrical wiring Instructions ImporTanT noTICe: The electrical wiring of this spa must meet the requirements of the National Electrical Code/USA (NEC) and any applicable state or local codes. The electrical circuit must be installed by a qualified electrician and ap...

16 J-300 Series ANSI/NFPA 70. The disconnecting means must be readily accessible to the spa’s occupant but installed at least 5 feet (1.5m) from spa water. 7. The electrical circuit supplied for the spa must include a suitable ground fault circuit interrupter (GFCI) as required by NEC/USA Article 68...

17 J-300 series J-300 Series Figure B Control Box TB1 3 2 1 1. Terminal Block 2. Bonding Lug 3. Grounding Terminal GRN WHT WHT BLK BLK BLK RED 1 2 3 Figure-C TB1 to Circuit Board Power In GRN WHT WHT BLK BLK BLK RED RED RED 1 2 3 Figure-D TB1 to Circuit Board Power In Move Red Wire Here north americ...

18 J-300 Series 8.0 spa Fill up procedure For best results, read each step in its entirety before proceeding with that step. 1. prepare The spa For Filling Clear all debris from the spa. (Although the spa shell has been • polished at the factory, you may want to treat it with a specially formulated ...

20 J-300 Series 8. place Cover on spa Keeping the insulating cover in place anytime the spa is not in • use will reduce the time required for heating, thereby minimizing operating costs. The time required for initial heat-up will vary depending on the • starting water temperature. DanGer: rIsK oF pe...

21 J-300 series J-300 Series 10. Leave spa cover open during this step to allow excessive chemical vapors to exit spa, protecting pillows and plastic knobs from chemical attack. If spa is indoors, open doors and windows for proper ventilation. Turn on all jet pumps for one hour, then place the massa...

22 J-300 Series warnInG: rIsK oF personal InJurY. To decrease the risk of injury, entrapment or drowning, • never leave your hot tub unattended for any reason, es- pecially if while the cover is open and accessible to small children and animals! To decrease the risk of • contracting a waterborne ill...

23 J-300 series J-300 Series 9.0 Control Functions 9.1 Control panel A. leD Display: Can display current water temperature (default display), water temperature set point, selected filtration/ heating mode, and error messages. B. warmer ( ) Button: Increases water temperature set point. C. Cooler ( )...

24 J-300 Series 9.2 General spa Features and Controls 1 7 8 11 2 2 2 2 2 5 5 3 4 6 13 13 13 13 15 14 5 10 10 10 12 18 18 18 9 6 16 17 17 17 17 16 Control Panel 1. Toggle Air Controls 2. Filter/Skimmer Grill 3. PowerPro MX Jets 4. Therapy Jets 5. Massage Selector Valves 6. Therapy Seat 7. Spa Light 8...

25 J-300 series J-300 Series 10.0 operating Instructions The spa control system has automatic functions that operate upon start-up and normal operation to protect the system. Upon power up, the readout displays the following information:1. Control panel displays current software release (e.g. 3.57),...

26 J-300 Series 10.3 light on/off button Pressing this button activates the waterfall, footwell light, lighted cup holders, backlit pillows and optional exterior lights in unison as follows: high - medium - low - off. note: Lights automatically turn off after 2 hours. 10.4 light mode Button This but...

27 J-300 series J-300 Series 10.6 selecting Desired massage action All models incorporate a massage selector valve that allows you to customize the massage and performance by diverting water between various jet systems within the spa. Simply turn valve to positions A, B or C to divert water pressure...

28 J-300 Series 11.0 automatic Filtration Cycles Your new spa includes a 24-hour circulation pump which filters the water continuously. The circulation pump draws water through the skimmer bag and one of two filter cartridges to effectively remove small debris in your spa. note: The 24-hour circulat...

29 J-300 series J-300 Series standard Filtration/heating Modes F0 5 minutes of filtration per day (one 5 minute “Blow-Out” cycle every 24 hours to purge all plumbing lines) F1 1 hour of filtration per day (one 30-minute cycle every 12 hours); This is the factory default setting. F2 1.5 hours of filt...

30 J-300 Series 12.0 spa maintenance Proper and regular maintenance of your spa will help it retain its beauty and performance. Your authorized Jacuzzi dealer can supply you with all the information, supplies, and accessory products you will need to accomplish this. DanGer: rIsK oF severe InJurY or ...

31 J-300 series J-300 Series An optional chemical feeder is available through your authorized Jacuzzi dealer that installs under the filter cap (#2472-673). Always remove the chemical feeder cap and feeder (when used) during the filter cleaning process by turning the cap handle counterclockwise. Rei...

33 J-300 series J-300 Series Periodically, the filter cartridge will need a more thorough cleaning to remove imbedded oils and minerals. For this, we suggest cleaning as illustrated in step “F”, followed by soaking the filter overnight in a plastic container filled with a solution of water and speci...

34 J-300 Series 12.3 pillow Care Remove and clean the headrest pillows as needed with soapy water using a cloth or soft-bristle brush. Always remove the pillows when adding chemical shock treatment to the spa water. When the sanitizer reading is below 4.0 ppm, pillows can be reinstalled. CauTIon: Ne...

36 J-300 Series 12.8 restarting Your spa in Cold weather If you want to start up your spa after it has sat empty for a time in freezing temperatures, be aware that the water remaining in certain sections of the piping may still be frozen. This situation will block water flow preventing the spa from ...

37 J-300 series J-300 Series the ability of the sanitation agents to keep the spa clean is severely affected as the pH moves beyond the ideal range. That is why almost all spa water test kits contain a measure for pH as well as the sanitizer. 13.2 sanitizing To destroy bacteria and organic compounds...

39 J-300 series J-300 Series 14.6 panel Flashes Fl1 or Fl2 A flashing “FL1” display means the flow switch is malfunctioning open, the filter cartridge is excessively dirty or an “air lock” condition has occurred at the circulation pump intake. A flashing “FL2” display means the flow switch is malfun...

40 J-300 Series 15.0 troubleshooting Procedures In the event your Jacuzzi spa is not working the way it should, please first review all the installation and operating instructions in this manual and check for messages on the panel display. If you are still not satisfied it is working properly, pleas...

41 J-300 series J-300 Series 15.5 no Heat 1. Check thermostat setting. 2. Keep the spa cover in place while heating. 3. Check the settings to see if your spa is in economy filtration/heating mode (page 28 ). Should checking the above steps fail to correct the problem, please call your Jacuzzi Hot Tu...

42 J-300 Series 16.0 Circuit Board Diagrams 16.1 north american J-335, J-345, J-355, J-365 and J-375 Dedicated power models (60 Hz) This wiring diagram is used for all North American, 240V (60 Hz) dedicated power models. Optional Stereo And Power Supply (not of fered on J-325 Models) Power Supply O ...

43 J-300 series J-300 Series 16.2 north american J-315 and J-325 Convertible Power Models (60 Hz) This wiring diagram is used for all North American 120/240V 60 Hz convertible power models. note: Optional 120/240 VAC 4-wire connection enhances heater output from 1kW to 4kW. O zo na to r (O pt io na ...

44 J-300 Series 16.3 export J-335, J-345, J-355, J-365 and J-375 Models (50 hz) This wiring diagram is used for all Export 230 VAC 50 Hz spa models. Optional Stereo And Power Supply Power Supply O ZO N AT O R (o pt io na l) O 3 GRN TB1 230 V AC 3-W ire Connection (50Hz, 1-Phase Service) USE COPPER C...

46 J-300 Series 17.0 optional stereo receiver Functions 17.1 stereo receiver Control Functions 15 1 20 19 17 18 22 21 16 4 8 2 5 6 7 3 13 12 11 9 10 14 SAT INFO AS-PS XBAS 2 ZONE SUBW BAND SE AR CH INT RPT RDM AUDIO ENTER MODE MULTI-ENVIRONMENTPLAYER TOP MENU AQ-CD-3 models equipped with the stereo ...

47 J-300 series J-300 Series B. “MENU” will be displayed for 2 seconds, and then “CONTRAST” will appear on the display. C. To navigate through the menus use the ( ) or ( ) buttons or press the MENU button repeatedly. D. To adjust the selected menu item, press the VOLUME Up (7) or Down (8) buttons. E...

48 J-300 Series 15 1 20 19 17 18 22 21 16 4 8 2 5 6 7 3 13 12 11 9 10 14 SAT INFO AS-PS XBAS 2 ZONE SUBW BAND SE AR CH INT RPT RDM AUDIO ENTER MODE MULTI-ENVIRONMENTPLAYER TOP MENU AQ-CD-3 6. audio/enter button: Press Audio/Enter to navigate through the stereo sound functions. Short press “AUDIO“ bu...

50 J-300 Series 15 1 20 19 17 18 22 21 16 4 8 2 5 6 7 3 13 12 11 9 10 14 SAT INFO AS-PS XBAS 2 ZONE SUBW BAND SE AR CH INT RPT RDM AUDIO ENTER MODE MULTI-ENVIRONMENTPLAYER TOP MENU AQ-CD-3 treble (treble level) • : User has 5 seconds to use the Volume Up or Down button to adjust the desired Treble l...

52 J-300 Series 15 1 20 19 17 18 22 21 16 4 8 2 5 6 7 3 13 12 11 9 10 14 SAT INFO AS-PS XBAS 2 ZONE SUBW BAND SE AR CH INT RPT RDM AUDIO ENTER MODE MULTI-ENVIRONMENTPLAYER TOP MENU AQ-CD-3 18. Preset 4/rDM button: In Tuner mode, any station can be stored as preset 4 by simply pressing and holding th...

53 J-300 series J-300 Series as a strong station is found. In CD mode, pressing this button will advance the CD down to the previous track, the track number is shown on the display panel. Simply press and hold the button to rewind through a track. CD play starts when the button is released. 23. Disp...

54 J-300 Series folders are accessed in order in which they were written by the CD writer. Therefore, the playing order may not be the same as the order in which they are expected. For example, a disc with the following folder/file hierarchy is subject to folder select, file select and play back ord...

56 J-300 Series A. CD/MP3/wMa File/folder play 1. There are three different play methods as following: Press the M2 button more than 3 seconds during playing an MP3/ • WMA disc for “intro play” to all files of the current folder. Intro play should restart from the first song of the current folder, a...

57 J-300 series J-300 Series C. ID3 information display For any MP3/WMA file recording with ID3 Tag information. The • ID3 information such like Album title, Track title, Artist Title will be displayed and automatic scrolling through the LCD while the file is playing. User also allows pressing the A...

58 J-300 Series Sound skips. The installation angle is more than 30 degrees Adjust the installation angle to less than 30 degrees The disc is extremely dirt or defective disc Clean the compact disc. Then try to play a new one The radio does not work. The radio station automatic selection does not wo...

59 J-300 series J-300 Series Seek/Track Down Button: • In CD mode: Press to rewind tracks or press and hold to do a fast rewind. • In radio mode: Seeks down for stations. Play/Pause Button: Press once topause track, press again to resume. Seek/Track Up Button: • In CD mode: Press to move forward tra...

60 J-300 Series 17.6 optional iPod®/MP3 Player Connection A. Connecting your iPod/MP3 Player 1. Plug in the iPod/MP3 Player (purchased separately) with supplied mini RCA cable into the auxiliary port (Figure A). 2. Plug the other end of the supplied cable into the phone jack connection on the iPod/M...

61 J-300 series J-300 Series 17.7 wireless remote Battery replacement procedure 1. T urn the remote unit over and locate the battery door (Figure A). 2. Rotate the battery door, with a coin, counterclockwise until the dot aligns with the Open arrow (Figure B). 3. Remove battery door using coin to pr...