INSTEON 2478D - Manuals

INSTEON 2478D – Manual in PDF format online.

Manuals:

Manual

Manual INSTEON 2478D

Summary

Page 4 - Installation; CAUTIONS AND WARNINGS; Tools Needed; Slotted screwdriver

Page 4 of 19 2478D - Rev: 1/21/2014 7:32 AM • Quick-Start Guide Installation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This product is intended for installation in accordance with the National Electric Code and local regulati...

Page 5 - Installing SwitchLinc – with 1 Switch; SwitchLinc Wire; Table A

Page 5 of 19 2478D - Rev: 1/21/2014 7:32 AM Installing SwitchLinc – with 1 Switch 1) Turn off circuit breaker(s) or remove fuse(s) feeding wall box 2) Use a voltage meter to verify that power is off 3) Remove wallplate from the switch and unscrew switch you are replacing and gently pull out 4) Disco...

Page 7 - Synchronized

Page 7 of 19 2478D - Rev: 1/21/2014 7:32 AM SwitchLinc’s LED bar and connected light will turn on Only SwitchLinc in box 2 will operate the Load until you synchronize Scenes to both SwitchLincs in next step 20) Add both SwitchLincs to a Scene as a Controller and Responder of each other (see Synchron...

Page 8 - 8) Connect bare Ground wire from

Page 8 of 19 2478D - Rev: 1/21/2014 7:32 AM 13) Connect bare Ground wire from SwitchLinc to bare Ground wire or Ground screw in the wall box 14) Connect W hite Neutral wire from SwitchLinc to Neutral wire(s) in wall box (usually White) 1 15) Cap Red wire from the SwitchLinc 16) Connect the Black wir...

Page 9 - Using SwitchLinc; LEDs

Page 9 of 19 2478D - Rev: 1/21/2014 7:32 AM On LED Off LED Using SwitchLinc LEDs LED Status Meaning Bottom LED of Brightness Bar On SwitchLinc powered up load off LEDs on Brightness Bar On Level of load brightness load on • On LED (White) o Illuminated when SwitchLinc is On • Off LED (White) o Illum...

Page 10 - INSTEON Programming; Add SwitchLinc to a Scene as a Responder

Page 10 of 19 2478D - Rev: 1/21/2014 7:32 AM 2) Once the desired brightness has been achieved, tap the Set button on your dimmer once SwitchLinc will (Beep) a. The local On-Level has now been set. If you would like to set up a Controller to set your dimmer to the above On-Level as well, proceed to s...

Page 11 - Add SwitchLinc to a Scene as a Controller; Add Multiple Scene Responders); Remove SwitchLinc from a Scene as a Controller; Remove Multiple Scene Responders; LED Brightness

Page 11 of 19 2478D - Rev: 1/21/2014 7:32 AM Add SwitchLinc to a Scene as a Controller Follow the steps below to control a Scene (one or more INSTEON devices) from a SwitchLinc paddle 1) Press & hold SwitchLinc’s Set button until it beeps SwitchLinc’s LED will blink 2) Adjust the Scene Responder...

Page 12 - X10 Programming; Advanced Features; Add Multiple Scene Responders; Synchronize Scenes with 2 SwitchLincs and identify them as A and B

Page 12 of 19 2478D - Rev: 1/21/2014 7:32 AM X10 Programming Instructions on setting X10 primary address and Scene addresses can be found online: http://www.smarthome.com/insteon-x10-programming.html Advanced Features Add Multiple Scene Responders (formerly “Multi-Linking Mode”) 1) Press & hold ...

Page 13 - Switch A’s LED will blink; Air Gap; Pull Set button out (creating an Air Gap)

Page 13 of 19 2478D - Rev: 1/21/2014 7:32 AM Synchronized Scene with 4 members (3-way/4-way) Software is recommended, however, the following steps, when carefully followed, will also work. For our example we will Synchronize SwitchLincs and identify them as switches A, B, C and D. 1) Turn all switch...

Page 14 - Change Paddle and LED Colors; Accessories page on; Local Ramp Rate; Setting the Ramp Rate; Connected light(s) will ramp up and down at the new rate

Page 14 of 19 2478D - Rev: 1/21/2014 7:32 AM Change Paddle and LED Colors You can swap out the included white LEDs and/or front paddle and trim frame assembly with a color-change kit before or after SwitchLinc is installed. For more information, see the Accessories page on INSTEON.com . Local Ramp R...

Page 15 - Additional Resources; Optional Accessories; Paddle Color Change Kit; Beeper Behavior; Single Beep: Transition from one setup mode to another; Blink LED on INSTEON Traffic; SwitchLinc bottom LED will turn on solid and then turn off

Page 15 of 19 2478D - Rev: 1/21/2014 7:32 AM Additional Resources Find home automation solutions, helpful tips, interactive demos, videos, user forums, and more at the Smarthome Learning Center: www.smarthome.com/learningcenter.html Optional Accessories Paddle Color Change Kit http://www.smarthome.c...

Page 16 - Specifications

Page 16 of 19 2478D - Rev: 1/21/2014 7:32 AM After a few seconds, SwitchLinc will (Beep)-(Beep) SwitchLinc will turn load on full bright Specifications General Product Name SwitchLinc Dimmer - INSTEON Remote Control Dimmer 100 - 277VAC 50/60Hz (Dual-Band) Brand Smarthome Manufacturer Product Number ...

Page 17 - Troubleshooting; Problem

Page 17 of 19 2478D - Rev: 1/21/2014 7:32 AM Case Color Available in White, Ivory, Almond Set Button 1, clear Plastic UV Stabilized Polycarbonate Beeper Yes LED White Dimensions 4.1" H x 1.8" W x 1.2" D Weight 3.6oz Operating Environment Indoors Operating Temperature Range 0 - 104 degree...

Page 18 - ee

Page 18 of 19 2478D - Rev: 1/21/2014 7:32 AM The Controller turns SwitchLinc Off, but not On Ramp Rate may be extremely slow Re-Add to Controller with fast Ramp Rate (s ee Local Ramp Rate ) SwitchLinc may be Added to the Scene in the Off state Turn on the light and then re-Add SwitchLinc to the Cont...

Page 19 - Certification and Warranty

Page 19 of 19 2478D - Rev: 1/21/2014 7:32 AM Certification and Warranty Certification This product has been thoroughly tested by Intertek Testing Services (ETL), a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been ...