Page 3 - About Keypad Dimmer; Features and Benefits; Integrated dimmer featuring 32 dim levels and 32 ramp rates
Page 3 of 24 Rev: 7/25/2013 9:16 AM About Keypad Dimmer Congratulations on your purchase of the elegant, high quality Keypad Dimmer. This in-wall switch with a built-in dimmer can control up to 5 or 8 INSTEON/X10 scenes. Additionally, each button has an LED that can be easily configured as a status ...
Page 4 - Before Installation; CAUTIONS AND WARNINGS; In the Box; Button Naming
Page 4 of 24 Rev: 7/25/2013 9:16 AM Before Installation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This product is intended for installation in accordance with the National Electrical Code and local regulations in the United S...
Page 5 - Installation – Circuit with 1 Switch; Keypad Wire; Keypad’s LEDs will illuminate; Installation – Circuit with 2 Switches; Note: the other 2 wires connected to this switch are Traveler wires
Page 5 of 24 Rev: 7/25/2013 9:16 AM Installation – Circuit with 1 Switch 1) Turn off circuit breaker(s) which feed the switch junction box (or remove fuse(s)). Verify that the power is off. 2) Remove trimplate from the switch, unscrew the switch you are replacing and gently pull out from wall 3) Dis...
Page 6 - Traveler wire to the black wire on Keypad A with a wire nut
Page 6 of 24 Rev: 7/25/2013 9:16 AM 6. Turn breaker(s) off 7. Connect the Line wire and the black 5 Traveler wire to the black wire on Keypad A with a wire nut 8. Cap the other Traveler wire with a wire nut 9. Cap A’s red wire 10. Connect neutral to A’s white wire 11. Connect Ground to A’s bare copp...
Page 7 - Installation – Circuit with 3 (or more) Switches; All Keypads’ LEDs will illuminate
Page 7 of 24 Rev: 7/25/2013 9:16 AM Installation – Circuit with 3 (or more) Switches Circuits with 3 switches are called 4-way circuits, circuits with 4 are called 5-way, and so on. All switches in multi-way circuits need to be replaced by either a Keypad and/or SwitchLinc). 1. Turn off the circuit ...
Page 8 - Local Control; LEDs
Page 8 of 24 Rev: 7/25/2013 9:16 AM Local Control LEDs Button LED Meaning ON On All on OFF On All off MAIN On/Off On All on MAIN On/Off Off All off Scene button On Scene members are on Button Taps Button Type Button LED State before Tap Effect of Tap Effect of Double-tap Toggle Off Turn scene On Tur...
Page 9 - INSTEON Setup; Add Keypad Button to a Scene as a Controller; ) Press and hold Keypad’s Set button until Keypad beeps; Remove Keypad Button from a Scene as a Controller; ) Press and hold the Keypad’s Set button until it beeps
Page 9 of 24 Rev: 7/25/2013 9:16 AM INSTEON Setup A scene consists of 1 or more INSTEON devices that respond to 1 or more INSTEON controller(s). When the scene is activated (turned on), all scene members return to the states they were at when the scene was programmed. INSTEON scenes let you activate...
Page 10 - Adding Keypad Button to a Scene as a Responder; Advanced Features; Add Multiple Scene Responders
Page 10 of 24 Rev: 7/25/2013 9:16 AM Adding Keypad Button to a Scene as a Responder 1) Press and hold the scene controller button until it beeps 11 Controller’s LED will blink 2) Tap the Keypad button you wish to be a responder of the scene at least once 3) Tap the button again if necessary to get t...
Page 11 - Remove Multiple Scene Responders
Page 11 of 24 Rev: 7/25/2013 9:16 AM - Adjust the responder to the desired scene state (for Keypads you must tap the button at least once to reach the desired state). - Press and hold responder’s Set button until it beeps and/or LED flashes Keypad will double-beep 5) After all responders have been a...
Page 12 - Have a button on the keypad control the load as part of a scene.; Toggle; – toggles between on and off commands each time it is tapped; Always On; – sends on every time it is tapped
Page 12 of 24 Rev: 7/25/2013 9:16 AM B’s scene controller LED will blink and Set button LED will blink green 5) Press and hold Switch A’s Set button until it double-beeps (or LED flashes) A will double-beep and its scene controller button and Set button LED will flash B will double-beep and its LEDs...
Page 13 - will; Adjust LED Brightness; Turn Button Beep On or Off; -Button Configuration; Add X10 Address to a Button; ) Tap the Keypad scene button you want to add
Page 13 of 24 Rev: 7/25/2013 9:16 AM 4) Tap the scene button you want to change 5) Press and hold Keypad’s Set button until it beeps The scene button’s LED will begin blinking and Set button LED will blink green All illuminated LEDs on Keypad will brighten to 100% 6) Press and hold Keypad’s Set butt...
Page 14 - Remove X10 Address from a Button; Wait 10 seconds
Page 14 of 24 Rev: 7/25/2013 9:16 AM 2) Press and hold Keypad’s Set button until it beeps. Set button LED will blink green 3) Send the desired X10 Address plus ON 3 times in a row (e.g. send B5-BON-B5-BON-B5-BON) Keypad will double-beep and the Set button LED will stop blinking Remove X10 Address fr...
Page 15 - Adjust Local Settings; LED Behavior
Page 15 of 24 Rev: 7/25/2013 9:16 AM Adjust Local Settings Each of the Keypad buttons is considered a “scene button,” meaning you can use any of the buttons on Keypad to create INSTEON scenes. Each button will control its own scene, only sending commands to devices linked specifically to that button...
Page 16 - ) Tap the Set button; Air Gap
Page 16 of 24 Rev: 7/25/2013 9:16 AM Local On-Level The local on-level is the default brightness level at which the light(s) physically wired to Keypad will turn on. The default local on-level is 100%, but can be set to any one of 33 settings, 32 fixed brightness levels (3% to 100%) or “Resume Brigh...
Page 17 - Configuring for 6 or 8-Button Operation; Changing to 6-Button Configuration; Changing to 6 or 8-Button Plate; Changing to 6 or 8-Button Plate
Page 17 of 24 Rev: 7/25/2013 9:16 AM Note: For proper operation, Keypad must be programmed to operate in 6-button or 8-button mode, corresponding to whichever plate is attached. See Configuring for 6 or 8-Button Operation . Configuring for 6 or 8-Button Operation Changing to 6-Button Configuration 1...
Page 18 - Changing Buttons; only; Brightness Level; ) Double-tap the Set button on your Keypad; Optional Accessories; For a list of accessories, please visit:
Page 18 of 24 Rev: 7/25/2013 9:16 AM Changing Buttons Keypad buttons can be swapped out with custom-etched buttons to customize its appearance. Using a small, flat-edged screwdriver only , carefully pry up on the sides of the keys from the middle of the keypad (when possible). Make sure you are cent...
Page 19 - Specifications
Page 19 of 24 Rev: 7/25/2013 9:16 AM Specifications General Product Name Keypad Dimmer - INSTEON 6/8-button Scene Control Keypad with Dimmer (Dual-Band) Brand INSTEON Manufacturer Product Number 2334-2xx where xx could be any number between 0 and 9. UPC 2334-222 813922013108 Keypad Dimmer, 8 Button,...
Page 21 - Troubleshooting; Problem; Keypad is not getting power.
Page 21 of 24 Rev: 7/25/2013 9:16 AM Troubleshooting NOTE: Unless they have been unlinked, INSTEON devices that had been previously linked to Keypad Dimmer Dual-Band will still respond to button presses, even after a factory reset. The reason is that the INSTEON devices themselves have not been unli...
Page 22 - Perform a factory reset. See
Page 22 of 24 Rev: 7/25/2013 9:16 AM When I try to turn on my light with another Controller, the light turns on, then back off. Keypad may be set up with an INSTEON On-Level at a high brightness and an X10 Primary or scene address On-Level at a low brightness. Remove the X10 Primary Address or X10 s...
Page 23 - Circuit Interrupter #MP215AFCP
Page 23 of 24 Rev: 7/25/2013 9:16 AM Circuit Interrupter #MP215AFCP Install power line noise filter between the output and the load. There might be loose connections within your home's wiring. Consult an electrician to check the wiring in your home. If you have tried these solutions, reviewed this O...
Page 24 - Certification and Warranty
Page 24 of 24 Rev: 7/25/2013 9:16 AM Certification and Warranty Certification This product has been thoroughly tested by Intertek Testing Services, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and ...
