INSTEON 2475D - Manuals - manualsarea.com

Page 3 - In-LineLinc Dimmer – Features and Benefits; Features

Page 3 of 13 2475D - Rev: 1/21/2014 7:17 AM In-LineLinc Dimmer – Features and Benefits Congratulations on purchasing the high-quality INSTEON In-LineLinc Dimmer Switch. With this easy-install module, you can add conveniently hidden, fully-dimmable remote control to not only the lights wired to In-Li...

Page 4 - Quick Start Guide; Preparing to Install In-LineLinc; Tools Needed; Flathead screwdriver; Installing In-LineLinc

Page 4 of 13 Rev: 1/21/2014 7:17 AM What’s in the Box? - In-LineLinc Dimmer - Quick Start Guide - Two (2) mounting screws - Three (3) wire nuts Preparing to Install In-LineLinc CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This p...

Page 5 - The load will turn on and off.; Using In-LineLinc Dimmer; Button Functions; An Important Note About INSTEON Networks; dual-band INSTEON products

Page 5 of 13 Rev: 1/21/2014 7:17 AM 6) Referring to the diagram at right and the table below, use the included wire nuts to connect the fixture’s Line, Load, Neutral and Ground wires to In-LineLinc’s corresponding wires. 7) Enable power to the switch from the circuit breaker or fuse panel. 8) Use In...

Page 6 - Linking In-LineLinc Dimmer as an INSTEON Responder; for 3 seconds or the On/scene button for 10 seconds.; Unlinking In-LineLinc Dimmer as an INSTEON Responder; for 3 seconds; Advanced Features; Setting the Local On-Level; The load connected to In-LineLinc will turn on at the local on-level.; Setting the Ramp Rate

Page 6 of 13 Rev: 1/21/2014 7:17 AM Linking In-LineLinc Dimmer as an INSTEON Responder Be sure to link In-LineLinc Dimmer to an INSTEON controller before you finish installing the fixture. Refer to your controller device’s Quick Start Guide or Owner’s Manual to properly link it to In-LineLinc. Most ...

Page 7 - Brightness Level; In-LineLinc’s status LED will blink; Creating INSTEON Scenes

Page 7 of 13 Rev: 1/21/2014 7:17 AM When setting the ramp rate, the speed is determined using the load’s brightness level. Refer to the table below while programming to set the desired ramp rate: 1) Using either the local ON and OFF buttons or a controller (if In-LineLinc Dimmer is already linked to...

Page 8 - Factory Reset; Additional Resources

Page 8 of 13 Rev: 1/21/2014 7:17 AM Factory Reset Factory Reset clears all user settings from In-LineLinc Dimmer, including INSTEON scenes, on-levels, ramp rates, X10 addresses, etc. 1) Make sure In-LineLinc Dimmer is unlinked from all controllers. 2) Turn off the breaker supplying power to In-LineL...

Page 9 - Specifications

Page 9 of 13 Rev: 1/21/2014 7:17 AM Specifications General Product Name In-LineLinc Dimmer Brand INSTEON Manufacturer Product Number 2475D, INSTEON In-LineLinc Dimmer UPC 689076402743 Patent Number Protected under U.S. and foreign patents (see www.insteon.com) Warranty Two years, limited Operation O...

Page 10 - Troubleshooting; Problem

Page 10 of 13 Rev: 1/21/2014 7:17 AM Voltage 120 volts AC +/- 10%, 60 Hertz, single phase Power W ire Leads 6", 16 AWG, stranded,600V, 105°C insulation, ends stripped and tinned, LINE (black), LOAD (red), NEUTRAL (white) Ground Lead 6”, 18 AWG, stranded, bare copper Maximum Dimmer Load 600 watts...

Page 11 - Adding

Page 11 of 13 Rev: 1/21/2014 7:17 AM interference with older X10 BoosterLinc technology. Upgrade to INSTEON-compatible BoosterLinc modules (#4827) . In-LineLinc doesn't always respond to an INSTEON controller. The INSTEON controller may have been reset without first unlinking In-LineLinc from it. Re...

Page 13 - Certification and Warranty

Page 13 of 13 Rev: 1/21/2014 7:17 AM Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the ...