Honeywell TB7100A1000- Manuals

Page 2 - TB7100A1000 MULTIPROTM MULTISPEED AND MULTIPURPOSE THERMOSTAT; ORDERING INFORMATION

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 2 ORDERING INFORMATION When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the TRADELINE® Catalog or price sheets for complete ordering number. If you have additional q...

Page 3 - Resistance Characteristics of Remote Sensors:

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 3 63-2675—03 NOTE: Alkaline batteries keep calendar and time if lithium battery is no longer functional. Resistance Characteristics of Remote Sensors: C7189U Remote Indoor Sensor: 10K ohm NTC. C7772 Flush-Mount Remote Indoor Sensor: 20K oh...

Page 4 - MERCURY NOTICE; INSTALLATION; CAUTION; Electrical Shock or Equipment Damage Hazard.; Select Thermostat Location

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 4 Fig. 4. C7189U Indoor Sensor dimensions in in. (mm). MERCURY NOTICE If this control is replacing a control that contains mercury in a sealed tube, do not place your old control in the trash. Dispose of properly. Contact your l...

Page 5 - WIRING; Electrical Shock Hazard.; IMPORTANT; System Type

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 5 63-2675—03 Fig. 7. Install wallplate. WIRING CAUTION Electrical Shock Hazard. Can cause electrical shock or equipment damage. Disconnect power supply before connecting wiring. IMPORTANT — All wiring must agree with applicable codes, ordi...

Page 6 - Table 5. Terminal Designation Descriptions.; Conventional System Wiring; Terminal

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 6 Table 5. Terminal Designation Descriptions. NOTES: 1. When used in a single-transformer system, leave metal jumper wire in place between Rc and R. If used on a two-transformer system, remove metal jumper wire between Rc and R....

Page 7 - Heat Pump System Wiring

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 7 63-2675—03 Fig. 13. Typical hookup of heat-only system. Fig. 14. Typical hookup of heat-only system with fan. Fig. 15. Typical hookup of cool-only system. Heat Pump System Wiring Fig. 16. Typical hookup of single-stage heat pump with no ...

Page 8 - Fan Coil System Wiring; Fig. 21. Typical hookup of PTAC with HI and LO fan speeds

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 8 Fan Coil System Wiring Fig. 18. Typical wiring of 4 pipe fan coil. Fig. 19. Typical wiring of 2 pipe fan coil with reheat. Fig. 20. Typical wiring of 2 pipe fan coil without reheat. PTAC System Wiring Fig. 21. Typical hookup o...

Page 9 - Fig. 22. Typical hookup of PTAC with HI and LO fan speeds; POWER THE THERMOSTAT; Wiring 24 Vac Common

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 9 63-2675—03 Fig. 22. Typical hookup of PTAC with HI and LO fan speeds (2H/1C). POWER THE THERMOSTAT You can choose from three methods to power the thermostat: • Batteries only (AAA alkaline). • 24 Vac direct connection only. • 24 Vac dire...

Page 10 - Wire Indoor Sensor; Can cause erratic system operation.; Sensor Wiring for Temperature Averaging; temperature averaging network.; SET CALENDAR AND TIME; Setting Calendar Once Functioning

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 10 Wire Indoor Sensor CAUTION Electrical Interference (Noise) Hazard. Can cause erratic system operation. Keep wiring at least one foot away from large inductive loads such as motors, line starters, lighting ballasts and large p...

Page 11 - INSTALLER SETUP; Advanced Settings

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 11 63-2675—03 Fig. 29. Setting calendar when thermostat is first powered. Fig. 30. Setting time when thermostat is first powered. INSTALLER SETUP Advanced Settings The thermostat has advanced settings to match the HVAC system. These settin...

Page 15 - MAIN SCREEN

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 15 63-2675—03 NOTE: Press the Done button to exit the Installer System Test. MAIN SCREEN Fig. 33. Main screen selections. Fig. 34. Main screen display. 0700 Temperature Display Offset 0 -3 (-1.5)— -3°F (-1.5°C) -2 (-1.0)— -2°F (-1.0°C) -1 ...

Page 16 - PROGRAMMING; Fan Settings

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 16 PROGRAMMING Table 7 shows default program settings. Table 7. Energy-saving Default Program Settings. Fan Settings Auto: Fan runs only when heating/cooling system is on. See the Fan Schedule section for more information. On: F...

Page 17 - OPERATION; Operating Sequence

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 17 63-2675—03 OPERATION Fan Sequence Operations (ISU 347, 348, 349) If heat pump or conventional application modes are enabled in ISU 170, then ISU 347 is not available for fan ramp algorithm. The fan operates as a default ON/AUTO selectio...

Page 19 - Special Programmable Mode Functions; Override Button, Temporary Override (Duration Limit ISU; Special Non-Programmable Mode Functions; Remote Setback; Setting Temperature Overrides; HOLD TEMPERATURE UNTIL; Fan Status Displayed on Main Screen

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 19 63-2675—03 Special Programmable Mode Functions Installer Setup 160 allows the thermostat to be configured for either a mode with a programmable 7 day schedule or as a non-programmable thermostat. Preoccupancy purge (ISU 185) This featur...

Page 20 - Reading Remote Indoor Temperature; ONE REMOTE INDOOR SENSOR INSTALLED; MULTIPLE REMOTE INDOOR SENSORS INSTALLED; Inside; Screen Locked; Fully Locked Screen; PARTIAL LOCKOUT 1

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 63-2675—03 20 Replace the batteries as follows: 1. Remove the thermostat from the base by pulling it straight out. (See Fig. 39.) 2. Install two new AA alkaline batteries with proper polar- ization. NOTES: — Always use AA alkaline batterie...

Page 21 - Temperature Recovery; Minimum-Off Timer Compressor Protection; TR21 Remote Temperature Sensor; Operation

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 21 63-2675—03 — Users cannot make changes to the temperature setpoint or any schedule, system, or fan settings. — The only features available are HOLIDAY and OVERRIDE. — To unlock the screen, see Advanced Settings section. Temperature Reco...

Page 23 - Symptom

TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT 23 63-2675—03 TROUBLESHOOTING (TABLE 12) Table 12. Troubleshooting. Symptom Possible Cause Action Display does not come on. Thermostat is not being powered. Check for 24 Vac between C and Rc. Check that AAA batteries are installed correctl...

Page 24 - Automation and Control Solutions; Perchlorate Material

Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 customer.honeywell.com TB7100A1000 MULTIPRO™ MULTISPEED AND MULTIPURPOSE THERMOSTAT ® U.S. Registered Trademark...