Honeywell L5100 ZWAVE - Manuals

Page 2 - LYNX Touch Installation and Setup Guide; RECOMMENDATIONS FOR PROPER PROTECTION; Provide Proper Coverage for the Protected Premises.; Recommendations for Smoke and Heat Detectors; In addition, we recommend the following:; sleeper if the door is closed.; THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE

LYNX Touch Installation and Setup Guide - 2 - RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations for Smoke and Heat Detectors With regard to the number an...

Page 3 - Table of Contents

LYNX Touch Installation and Setup Guide -3- Table of Contents System Features ..................................................................................................................................................................................... 5 Installing the Control ..................

Page 5 - UL; System Features

LYNX Touch Installation and Setup Guide - 5 - System Features The LYNX Touch L5200 and L7000 series controls are self-contained, rechargeable wireless control/communicator that features easy installation and usage. A built-in speaker provides voice annunciation of system status along with voice desc...

Page 6 - Communication

LYNX Touch Installation and Setup Guide - 6 - System Features Communication L5200 L7000  ADEMCO Contact ID    SIA (DC-03)    Internet central station communication    GSM cellular central station communication    WiFi Central station communication    Two-way voice communication   ...

Page 7 - Installing the Control; Wall Mounting; blade of a medium size screwdriver.; Desktop Mounting; connections to the control panel.

LYNX Touch Installation and Setup Guide - 7 - Installing the Control Wall Mounting For wall mounting follow the steps below and refer to the appropriate figure for the LYNX Touch L5200 OR L7000 control. 1. Release the front case assembly from the back case by depressing the two locking tabs at the t...

Page 9 - Wiring Connections; WIRING TABLE

LYNX Touch Installation and Setup Guide - 9 - Wiring Connections 5000-100-094-V4 Make Earth Ground Connection - The de s ign a ted e a rth gro u nd termin a l EGND m us t b e termin a ted in a good e a rth gro u nd for the lightning tr a n s ient protective device s in thi s prod u ct to b e effecti...

Page 10 - AC Power and Backup Battery; General; Installing the Rechargeable Backup Battery; battery; Battery Selection; Approximately 1-hour before battery depletion

LYNX Touch Installation and Setup Guide - 10 - AC Power and Backup Battery General The system is powered by a 9 Volt DC, 2.7 Amp Plug-in Power Supply, 300-04705/300-04705V1, or 300- 04065/300-04065V1 (300-04063/300-04063V1 or 300-04064/300-04064V1 in Canada). Refer to the wiring table below for wire...

Page 11 - L5200 Battery Installation; OR

LYNX Touch Installation and Setup Guide - 11 - AC Power and Backup Battery 5000-100-09 3 -V2 OR RETAINER S CREW RETAINER S CREW BATTERY CABLE CHANNEL BATTERY PACK(P/N 3 00-0 38 66/ LYNXRCHKIT- S HA) BATTERY PACK (P/N 3 00-0 38 64-1/ LYNXRCHKIT- S C) BATTERY WIRE ROUTING CLIP S ( 3 ) L5200 Battery In...

Page 12 - Installing/Configuring Communication & Home Automation Modules; Communications and Home Automation Modules:; Communications Module 24-Hour Standby Power; installed in the control.; RF Exposure; Connecting and Configuring GSM and IP Communication Modules; seated into the receptacle on the control.

LYNX Touch Installation and Setup Guide - 12 - Installing/Configuring Communication & Home Automation Modules General This LYNX Touch controls support Central Station reporting using wireless/cellular (GSM) WiFi and hardwire (IP) communications modules. They also support upload/download programm...

Page 13 - L5200 GSM Communications Installation

LYNX Touch Installation and Setup Guide - 13 - Installing/Configuring Communication & Home Automation Modules S CREW ( 3 ) S IM CARD 5000-100-151-V 3 ROTATED 1 8 0 CONNECTOR BOARD CONNECTOR BOARD RECEPTACLE 4GL/4GLC OR G S MVLP5-4G/G S MVLP5CN4G LYNX TOUCH L5200 LOCKING TAB S L5200 GSM Communica...

Page 14 - Installing the ILP5 Ethernet Communications Module; receptacle on the control.; Alternate Installation; (Refer to the Alternate Installation as shown on the figure below); L5200 IP Communications Module Installation

LYNX Touch Installation and Setup Guide - 14 - Installing/Configuring Communication & Home Automation Modules Installing the ILP5 Ethernet Communications Module Do not install the ILP5 if the L5100-WiFi communications module is being installed. Ensure that the connector board and cable are secur...

Page 15 - L7000 IP Communications Module Installation; Installing the L5100-WiFi module

LYNX Touch Installation and Setup Guide - 15 - Installing/Configuring Communication & Home Automation Modules 7000-100-014-V1 REMOVE ILP5 S PACER REMOVE ILP5 KNOCKOUT S CREW ( 3 ) ROTATED 1 8 0 CONNECTOR BOARD CONNECTOR BOARD RECEPTACLE ILP5 LYNX TOUCH L7000 TIE WRAPPOINT ILP5 S PACER TIE WRAP (...

Page 17 - Installing Wireless Zones; General Information; requires a programming zone; (see transmitter’s instructions for appropriate input type); button transmitters have replaceable batteries.

LYNX Touch Installation and Setup Guide - 17 - Installing Wireless Zones General Information Zones The L5200 and L7000 controls respectively support up to 79 and 103 total wireless zones using 5800 Series transmitters, and wireless buttons. Range The built-in RF receiver can detect signals from wire...

Page 18 - RF Sniffer Test Mode; amplitude when the system is in the normal operating mode.; SCREEN ACTION

LYNX Touch Installation and Setup Guide - 18 - Installing Wireless Zones RF Sniffer Test Mode This mode is used after all transmitters have been entered to check that all transmitters have been properly programmed. Sniffer mode does not automatically expire. You must manually exit Sniffer mode by se...

Page 19 - 800 Series Transmitter Loop Numbers; (Refer to this information when programming transmitters)

LYNX Touch Installation and Setup Guide - 19 - Installing Wireless Zones 5800 Series Transmitter Loop Numbers (Refer to this information when programming transmitters) The following illustration shows the compatible transmitters, their associated input types and loop designations. LOOP 1 5806/5806W3...

Page 20 - Mechanics of Programming; Navigating Menus; Touch-screen Display; Ready To Arm; Re; Key Description; Initiates panic alarm options when depressed for 4 seconds.

LYNX Touch Installation and Setup Guide - 20 - Mechanics of Programming Navigating Menus Touch-screen Display LYNX Touch’s Liquid Crystal Display (LCD) touch-screen displays variable icons and text on “screens”. The screen displays status icons and associated text, the current time and date, system ...

Page 21 - Navigation Keys; prompt when a specific input is required.; Home Screen; with the current weather forecast and a 5-Day Forecast button.; L5200 Home Screen with Total Connect Services; L7000 Home Screen with Total Connect Services; Icon or Button

LYNX Touch Installation and Setup Guide - 21 - Mechanics of Programming Navigation Keys Navigating through the screens is accomplished by lightly touching the icons or menu items on the touch-screen. Once activated, the control advances to the next screen. Selecting the “Home” (cancel) key or the “ ...

Page 22 - Security Screen; Refer to the paragraphs below for additional information.; Security Menu; Selection Function; Installer Tools Menu; The Tools/Installer Menu provides access to the; Installer Tools Menu Page; The User Menu provides access to the User; User Tools Menu Page

LYNX Touch Installation and Setup Guide - 22 - Mechanics of Programming Navigating Menus Security Screen System Status is displayed at the top of each screen and the time and date are displayed at the bottom of the Security Screen. The Security menu Screens differ between the LYNX Touch L5200 and th...

Page 23 - General Programming Information; section; Programming; Enter Installer Programming Mode; tem; System Standby Screen

LYNX Touch Installation and Setup Guide - 23 - Mechanics of Programming General Programming Information When power cycling the control, remove AC power first and wait approximately 1 minute before disconnecting battery. Programming options are stored in non-removable, electrically erasable, nonvolat...

Page 24 - Loading Factory Defaults; this manual to view the Default Values.; Select a Default Configuration; Exiting Program Mode; ” key as required until system displays a Confirmation screen.

LYNX Touch Installation and Setup Guide - 24 - Mechanics of Programming Loading Factory Defaults To load the factory defaults, enter the Installer Programming Mode and advance to second page of the System Programming and refer to following procedure. Refer to the Programming Default Values section o...

Page 25 - Zone Response Type Definitions; Type Function

LYNX Touch Installation and Setup Guide - 25 - Zone Response Type Definitions General Information During programming, you must assign a zone type to each zone, which defines the way in which the system responds to faults in that zone. Zone types are defined below. Type Function Characteristics Not U...

Page 27 - Programming the Control; Page 1; Enter Installer Programming Mode without using Installer Code; Change Installer Code; Installer Code; Select a Language; Language

LYNX Touch Installation and Setup Guide - 27 - Programming the Control After entering the System Programming mode select from the options provided on the First and Second Installer Programming tools screens as shown in the accompanying figure. System Programming... 5000-100-013- V 1 System Type Inst...

Page 28 - The following system options are programmed in this section:

LYNX Touch Installation and Setup Guide - 28 - Programming the Control System Type The following system options are programmed in this section: Option Function RF Jam Enable or disable RF Jam Log and Reporting Speaker Phone Enable or disable Speaker Phone mode. (Only available on the LYNX Touch L520...

Page 30 - Program Date and Time; Date Time

LYNX Touch Installation and Setup Guide - 30 - Programming the Control Program Date and Time Note: If applicable, preprogrammed defaults for the L5200/L7000 Control are shown on the screen unless otherwise noted. SCREEN ACTION 5000-100-131-V0 Date Time Note: If you are installing a 4GL/4GLC or GSMVL...

Page 31 - Program the Communications Module; Option Function; Communicator

LYNX Touch Installation and Setup Guide - 31 - Programming the Control Program the Communications Module A router is required if you are installing the L5100-WiFi module. The router must be powered on and connected for WiFi operation (alarm reporting) to occur. The following system options are progr...

Page 32 - Program the Communications Module (Continued)

LYNX Touch Installation and Setup Guide - 32 - Programming the Control Program the Communications Module (Continued) SCREEN ACTION City ID 4. Select “City ID”. Enter the 2-digit Primary City ID (Decimal). Options 01-99 CS ID 5. Select “CS ID”. Enter the 2-digit Primary Central Station ID (HEX). Opti...

Page 33 - Options; GSM Rollover; GSM 24 Hour Test; No

LYNX Touch Installation and Setup Guide - 33 - Programming the Control Program the Communications Module (Continued) GSM Fault Time (min) 00 19. Select “GSM Fault Time (min)”. Enter the time delay (in minutes) on the keypad. Options 00-99 GSM Rollover No 20. If “WiFi and GSM” was selected in step 2,...

Page 34 - Program the Z-Wave Module; Fahrenheit

LYNX Touch Installation and Setup Guide - 34 - Programming the Control Program the Z-Wave Module The following system options are programmed in this section: Option Function Z-Wave Enables or disables the Z-Wave Module Temperature Display Toggles between Fahrenheit and Celsius (for Z-Wave compatible...

Page 35 - Program Zones; Zones; Select “Zones”

LYNX Touch Installation and Setup Guide - 35 - Programming the Control Program Zones The following system options are programmed in this section: Option Function Serial Number Manually enter device serial number or enroll via RF transmission Loop Number Manually enter device loop number or enroll vi...

Page 37 - Supervision

LYNX Touch Installation and Setup Guide - 37 - Programming the Control Program Zones (Continued) Supervision Supervised Supervision The system displays the applicable Supervision options based upon the Device Type that was selected. Select “Supervision” to scroll between the following options: Hardw...

Page 38 - Program Keys; The following system options are programmed in this section; Keys

LYNX Touch Installation and Setup Guide - 38 - Programming the Control Program Keys The following system options are programmed in this section Option Function Key Type Select the specific type of key being entered or enrolled User Associates the Key with a specific User Serial Number Manually enter...

Page 40 - Program Reporting

LYNX Touch Installation and Setup Guide - 40 - Programming the Control Program Reporting When Compass service is required and GSM or IP are the only reporting channels: As part of Primary Central Station programming; the “Phone Type” must be set to any selection other than “None”, the “Communicator ...

Page 41 - Reporter

LYNX Touch Installation and Setup Guide - 41 - Programming the Control Program Reporting (Continued) Notes: If applicable, preprogrammed defaults for the L5200/L7000 Control are shown on the screen unless otherwise noted. When GSM is used as the Primary Communications channel for any Total Connect s...

Page 45 - The

LYNX Touch Installation and Setup Guide - 45 - Programming the Control Program Reporting (Continued) SCREEN ACTION Options Select “Options”. The System displays the following options: PBX Call Wait Cancel Number of Reports Alarm Report Delay First Report Offset Report Frequency PBX Note: This field ...

Page 46 - Ring Counter; Select “Flexible Callback”, the system toggles between “Yes” and “No”.

LYNX Touch Installation and Setup Guide - 46 - Programming the Control Program Reporting (Continued) Ring Counter 2 This option only appears if Answering Machine defeat is set to “No”. Enter ring counter (1 – 14 rings) on the displayed keypad. Flexible Callback No Select “Flexible Callback”, the sys...

Page 47 - Program Sounder; Sounder

LYNX Touch Installation and Setup Guide - 47 - Programming the Control Program Sounder The following system options are programmed in this section: Option Function Burglary Alarm Sound Switches the full 110 dB alarm sound for burglary On/Off. Burglary Bell Timeout Select the time for timeout of the ...

Page 48 - Program System Settings

LYNX Touch Installation and Setup Guide - 48 - Programming the Control Program System Settings The following system options are programmed in this section: Option Function Entry Delay1/Entry Delay 2 Selects an Entry Delay time in seconds. The system will wait the time entered before sounding alarm u...

Page 49 - System Settings; allowed

LYNX Touch Installation and Setup Guide - 49 - Programming the Control Program System Settings Note: If applicable, preprogrammed defaults for the L5200/L7000 Control are shown on the screen unless otherwise noted. SCREEN ACTION System Settings Select “System Settings” The System displays the follow...

Page 50 - Select “Exit Warning”. The System toggles between Yes and No.

LYNX Touch Installation and Setup Guide - 50 - Programming the Control Program System Settings (Continued) SCREEN ACTION Backlight Timeout No Select “Backlight Timeout”. The System toggles between No and 30 Seconds. Quick Arm Yes Select “Quick Arm”. The System toggles between Yes and No. Quick Exit ...

Page 51 - Communications Diagnostics; Communications Status; performs a self-test of the AES encryption algorithm as follows:; Ethernet Information; Displays IP information, if the IP communication path is enabled.; Message Meaning; GSM Information –; Displays GSM information if GSM communication path is enabled.; Status Message

LYNX Touch Installation and Setup Guide - 51 - Programming the Control Communications Diagnostics Communications Status – The system provides a status of the IP or GSM communications paths and performs a self-test of the AES encryption algorithm as follows: Message Meaning GSM: OK Normal; No fault. ...

Page 52 - Communications ID Numbers –; Displays programmed SIM card information; Test Communications –; Through the AlarmNet Direct website

LYNX Touch Installation and Setup Guide - 52 - Programming the Control Communications ID Numbers – Displays programmed SIM card information Message Meaning MAC: xxxxxxxxxxxx MAC Address indicates the unique identification number for installed communications module(s) MAC CRC: xxxx MAC CRC number for...

Page 53 - Register through AlarmNet Direct Website; location to be; Register by Phone; When instructed to do so, select; Register Device; in the LYNX Touch Diagnostics to complete the; Register through LYNX Touch Diagnostics; None; Ethernet; The registration message is sent and the unit waits

LYNX Touch Installation and Setup Guide - 53 - Programming the Control Register through AlarmNet Direct Website If you have programmed the communications module through AlarmNet Direct, you must then transfer the data to the module, and register the module. To do this, please go to: https://services...

Page 54 - Register; Register Device with PIN; Enter a 4-digit alphanumeric PIN number; Register Device With PIN

LYNX Touch Installation and Setup Guide - 54 - Programming the Control During the registration process the following messages may be displayed: Message Meaning Getting Configuration File… The configuration file is obtained from AlarmNet if the module was programmed through AlarmNet Direct or a previ...

Page 55 - Update Server; Enroll the L5100-WiFi Module; The module can be enrolled using one of the following procedures:

LYNX Touch Installation and Setup Guide - 55 - Programming the Control Update Server This procedure is used to upload the Configuration File to the Server. SCREEN ACTION Comm. Diagnostics 1. Select “Comm. Diagnostics” The System displays the following options depending upon the communication device ...

Page 56 - SCREEN; WiFi Location; Select “Configure WiFi”. The following options will be displayed”:; Enroll using Scan Access Points; Access Points” procedure.; Manually Configure Access Points; Open

LYNX Touch Installation and Setup Guide - 56 - Programming the Control SCREEN ACTION WiFi Location None 2. Select “WiFi Location”. The System will scroll between “None” and “Speaker Side”. After selecting “Speaker Side”, the “Configure WiFi” option will be displayed. 3. Select “Configure WiFi”. The ...

Page 57 - configured access point every time the system is powered up.; Factory Defaults; The following messages may be displayed:

LYNX Touch Installation and Setup Guide - 57 - Programming the Control 5. Select “DHCP”. The system scrolls between “Yes” and “No”. If “No” is selected the “Static” button is displayed. Note: When entering a password, up to 31 characters can be entered. The system will only display the first 22 char...

Page 58 - Equipment required to download to a system at the premises; Remote Programming Information; Downloader for Windows.

LYNX Touch Installation and Setup Guide - 58 - Remote Programming/Control (Downloading) General Information The control panel can be remotely programmed from an IBM-compatible Personal Computer (PC), Compass Downloader, a HAYES compatible Modem (L5200/L5200CN only) or via a capable GSM or IP Communi...

Page 59 - Remote Programming Advisory Notes; IP or WiFi

LYNX Touch Installation and Setup Guide - 59 - Remote Programming/Control (Downloading) Remote Programming Advisory Notes  A copy of the program downloaded may be printed using the IBM PC-compatible computer’s internal report generator, when an optional printer is connected (consult your PC manual ...

Page 60 - System Operation; Key/Touchscreen Operation; Zone Function; Security Codes; , but may be changed in the Installer Code programming; Master Code; In normal operation mode,; Enter/Change the Master Code by installer.

LYNX Touch Installation and Setup Guide - 60 - System Operation Key/Touchscreen Operation The keys and touchscreen allows the user to arm and disarm the system, and perform other system functions, such as bypassing zones. Zone and system conditions (ALARM, trouble, bypass) are displayed on the displ...

Page 61 - Secondary User Codes; Installer Programming Tools menu.; Security Code Notes; Instruct users to be careful not to use this code for normal usage.

LYNX Touch Installation and Setup Guide - 61 - System Operation Secondary User Codes In normal operation mode, the Master Security Code can be used to assign up to 30 (L5200/L5200CN) or 46 (L7000/L7000CN) secondary 4-digit security codes, including a Guest Code and a Duress Code. The Master Code can...

Page 62 - “Follow Me” System Announcement Feature (L5200/L5200CN Only)

LYNX Touch Installation and Setup Guide - 62 - System Operation “Follow Me” System Announcement Feature (L5200/L5200CN Only) This feature allows the LYNX Touch to deliver a voice system message to the Follow Me Phone numbers programmed by the installer. The LYNX Touch will first transmit reports to ...

Page 63 - (1) This feature is only supported if it has been programmed.; Remote Phone Control Feature

LYNX Touch Installation and Setup Guide - 63 - System Operation “Follow Me” Reminder Feature (L5200/L5200CN Only) The “Follow Me” feature allows the user to schedule a time driven message. When activated, the system will dial the Phone 1 and/or the Phone 2 telephone numbers, which are programmed as ...

Page 64 - System Displays; No WiFi source; Zone Status Displays; when a zone has been Faulted, Bypassed or in Alarm.

LYNX Touch Installation and Setup Guide - 64 - System Operation System Displays The following icons will be displayed on the Home screen along with specific zone status information (if applicable) to indicate system status. DISPLAY DEFINITION DISPLAY DEFINITION DISPLAY DEFINITION AC Loss Door Open F...

Page 65 - Audio alarm verification has not been evaluated by UL.; Activation; line, otherwise AAV commands may not go through.; Key; Ends the session and disconnects the phone line.

LYNX Touch Installation and Setup Guide - 65 - System Operation UL Audio alarm verification has not been evaluated by UL. Audio Alarm Verification (Two-Way Voice Feature) This feature allows the central station operator to listen, talk to or conduct a two-way conversation with an individual(s) at th...

Page 66 - Event Log; Contact ID® & SIA Event Log Codes

LYNX Touch Installation and Setup Guide - 66 - System Operation Event Log The LYNX Touch Series event log is capable of recording and displaying up to 128 (L5200/L5200CN) or 256 (L7000/L7000CN) system events. The type of events that can be recorded is selectable and is programmed in the System Type ...

Page 67 - Central Station Messages

LYNX Touch Installation and Setup Guide - 67 - System Operation Central Station Messages The following messages are sent by the L5100 communications modules (4GL/4GLC or GSMVLP5-4G/GSMVLP5CN4G, ILP5 and L5100-WiFi) for the conditions listed below. Alarm Condition Alarm Code Restore Code Power On / R...

Page 68 - TO THE INSTALLER; Test Modes; Testing the System; Notify the Central; zone number will be displayed. For; a report will be sent to the central station.

LYNX Touch Installation and Setup Guide - 68 - Testing the System TO THE INSTALLER Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibili...

Page 69 - Dialer Test; This test is not available for the LYNX Touch L7000/L7000CN.; Notify the; Station. The test will not be recorded in the Event Log.; Zone Discovery Mode; Enter Zone Discovery; Rebooting the System; “Diagnostics” button.; are operational in the system.

LYNX Touch Installation and Setup Guide - 69 - Testing the System Dialer Test Note: This test is not available for the LYNX Touch L7000/L7000CN. The Dialer Test checks that the phone connection to the central station is working properly. Notify the Central Station in advance that tests will be in pr...

Page 73 - LYNX Touch (L5200CN/L7000CN) Canada Programming Default Values

LYNX Touch Installation and Setup Guide - 73 - LYNX Touch (L5200CN/L7000CN) Canada Programming Default Values Program Function Configuration 1 Configuration 2 Configuration 3 Configuration 4 Installer Code 4112 4112 4112 4112 System Type RF Jam Disabled Disabled Disabled Disabled Speaker Phone (L520...

Page 76 - Zone Programming Default Values; Zone Programming Notes; Zone Assignment/Alarm Response Types for Configuration 1

LYNX Touch Installation and Setup Guide - 76 - Zone Programming Default Values Zone Programming Notes 1. Zone 1 is a hardwire zone; Zones 95, 96 and 99 are keypad panics. 2. For the LYNX Touch L5200/L5200CN Zones 2 to 64 are RF zones (Zones 46 to 48 are reserved for Garage Door Zones); Zones 140-155...

Page 77 - Zone Assignment/Alarm Response Types for Values 3 and 4; Zone Response Type Matrix

LYNX Touch Installation and Setup Guide - 77 - Zone Programming Default Values Zone Assignment/Alarm Response Types for Values 3 and 4 Zone Number Loop Number Device Type Response Type Alarm Report Chime Supervision Arm Night Zone Descriptor 1 --- New Not Used Yes Disabled End of Line n/a n/a 2 2 Do...

Page 78 - Regulatory Agency Statements; Federal Communications Commission (FCC) Part 15; FCC IC Statement; TELEPHONE/MODEM INTERFACE; Federal Communications Commission (FCC) Part 68; Industry Canada

LYNX Touch Installation and Setup Guide - 78 - Regulatory Agency Statements Federal Communications Commission (FCC) Part 15 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications...

Page 79 - WARNING

LYNX Touch Installation and Setup Guide - 79 - WARNING THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to c...

Page 80 - UL Notices; permissible for UL installations.

LYNX Touch Installation and Setup Guide - 80 - UL Notices 1. For UL Residential Burglar Alarm installations with line security, total exit delay time must not exceed 60 seconds. For UL Burglar Alarm installations without line security, total exit delay time must not exceed 120 seconds. 2. Periodic t...

Page 81 - SIA Quick Reference Guide

LYNX Touch Installation and Setup Guide - 81 - SIA Quick Reference Guide Programming Section Feature Range Shipping Default SIA Requirement Installation and Setup Guide or Programming Guide Reporter / Report Selection Exit Error Enabled or Disabled Enabled Enabled Recent Closing Enabled or Disabled ...

Page 82 - Specifications; LYNX Touch Series Security Controls; ADEMCO Contact ID® Reporting,

LYNX Touch Installation and Setup Guide - 82 - Specifications LYNX Touch Series Security Controls Physical: Dimensions: 8.5” W x 6” H x 1.875” D Electrical: Voltage Input: 9 Vdc from plug-in 2.7A power supply Rechargeable Backup Battery: Nickel-metal hydride battery pack rated at 7.2 Vdc Communicati...

Page 83 - Contacting Technical Support; documentation that came with the product.

LYNX Touch Installation and Setup Guide - 83 - Contacting Technical Support PLEASE, before you call Technical Support, be sure you: • READ THE INSTRUCTIONS! • Check all wiring connections. • Determine that the power supply and/or backup battery are supplying proper voltages. • Verify your programmin...

Page 84 - Glossary

LYNX Touch Installation and Setup Guide - 84 - Glossary AES – Advanced Encryption Standard APL – Advanced Protection Logic dBM – decibals milliwatt (power ratio) DHCP – Dynamic Host Configuration Protocol, which provides a mechanism for allocating IP addresses dynamically so that addresses can be re...

Page 85 - – Index –; Installing/configuring communication & home

LYNX Touch Installation and Setup Guide - 85 - – Index – 24-hour silent ................................................................. 60 300-03866 ......................................................................... 5 300-04063/300-04063V1 ................................................ 10...

Page 87 - YNX T

LYNX Touch Installation and Setup Guide - 87 - 5200-100-SOC-V0 2K OHM EOLR PO WER SUPPL Y CONNECT OR HARD WIRED ZONE WEEKL Y TE S TING I S REQ UIRED T O EN S URE PR OPER OPERA TION OF THI S S Y S TEM PREMISES TELEPHONE INCOMING PHONE LINE H/S T H/S R RING TIP EGND EARTH GR OUND HWZ1 TRIG GND GND +9V...

Page 88 - WARRANTY INFORMATION; For the latest warranty information, please visit:

WARRANTY INFORMATION For the latest warranty information, please visit: www.honeywell.com/security/hsc/resources/wa 2013 Ê800-160820Š 800-16082 12/13 Rev. A

Honeywell L5100 ZWAVE - Manuals

Manuals:

Manual Honeywell L5100 ZWAVE

User Manual Honeywell L5100 ZWAVE

Summary

Honeywell Manuals