Honeywell L5100 ZWAVE - Manual
Honeywell L5100 ZWAVE – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
LYNX Touch Garage Door Opener Operation with 5877GDPK
General Information
The 5877GDPK includes the 5877 Relay Receiver and a SSA1 Z-Wave
TM
Wireless Siren & Strobe Alarm. It
provides an audible and visible warning that the garage door opener is being remotely activated.
If the system has been equipped for garage door control, installation of both the 5877 and SSA1 is required for
remote unattended garage door control. The installation of a 5822T Tilt Sensor or Door/Window Transmitter
(i.e.; 5816) allows the system to provide the status of up to three Garage Doors (one transmitter per door). The
System can be armed when the garage door is open, and once the garage door has been closed, the zone will be
monitored as part of the security system. It can also be programmed for monitoring only without providing
burglary protection. The panel also features the option to automatically close the Garage Door(s) if it has been
left open for more than a specified (programmable) period of time (Close in) or at a specified time (Close at).
Do not use the 5877GDPK garage door automation with any garage door opener that lacks the safety features
required by U.S. federal safety standards (this includes any garage door opener model manufactured before
January 1, 1993). A garage door opener that cannot detect an object and stop and reverse the door – does not
meet current U.S. federal safety standards. Your garage door opener also must signal before unattended door
operation. For more information please consult your garage door opener manual.
Notes:
1. The system must be equipped with the L5100-ZWave Home Automation module.
2. The 5877GDPK is not compatible with:
- Chamberlin/Lift Master MyQ technology (Including but not limited to; Models 8550, 8360 and 8500).
- One piece or swinging garage doors.
3. Garage door control must have working entrapment protection (automatic reversing mechanisms and electronic photo eye
sensors that detect obstructions).
4. Both the 5877 Relay Receiver and the SSA1 Siren Strobe must be installed.
Enrolling the 5877 Relay Receiver and Including the SSA1 Siren/Strobe module
ACTION
NOTES
Note:
Ensure that the 5877 Relay Receiver is in close proximity to the
LYNX Touch while it is being enrolled. After the device has been
enrolled it can be mounted in its permanent position but should be
tested to make sure that it receives the Open/Close signals from the
LYNX Touch.
1. At the Home or Dashboard Screen select the “Automation” icon.
2. At the second page of the Automation Screen, select the Garage door
setup icon.
3. Select the Garage door to be enrolled, from the displayed list.
4. Select “Assign device.” The control advances to the Garage Door
operation screen.
5. Enter the 7-digit serial number associated with the 5877 Relay
Receiver then select “Done.”
6. At the 5877 Relay Receiver, depress the Program button.
7. To confirm enrollment, at the LYNX Touch select the “Learn” button
and listen for a click at the relay.
8. At the Garage Door setup screen, select “Include Siren” to include the
SSA1 siren/strobe module.
9. The panel displays “Entering Inclusion Mode. Please wait…” followed
by “Ready to Include device. Press the function button on device.”
Within one minute press the siren’s Function button.
10. If the module has been successfully enrolled, the panel displays
“Device Found! Please Wait” and then the device information is
displayed.
Note:
Repeat steps 2 through 10 to enroll up to two additional Garage
Doors.
11. Select the “
” button to return to the Automation screen.
•
If System Status is desired, a House ID must be
enrolled in the LYNX Touch. Refer to the System
Type Programming Section of the appropriate LYNX
Touch Installation and Setup Guide LYNX Touch
Programming Guide listed below
•
The 5877 Relay Receiver should be enrolled in the
LYNX Touch before it is permanently mounted.
•
The SSA1 Wireless Siren and Strobe module should
be “included” in the LYNX Touch before it is
permanently mounted.
•
The SSA1 Wireless Siren and Strobe module must
be “included” for each garage door that is controlled
by the 5877 relay receiver separately.
•
A single SSA1 Wireless Siren and Strobe module
can be “included” for up to three garage doors
controlled by the LYNX Touch L5100 or separate
modules can be “included” for each (up to 3) garage
doors/5877 Relay Receivers.
•
In order to display the garage door status, you must
also enroll a 5816 sensor or a 5822T Tilt Sensor.
Refer to the Zone Programming Section of the
appropriate LYNX Touch Installation and Setup
Guide or to the LYNX Touch Programming Guide
listed below.
•
The 5816 or 5822T is enrolled on Zones 46, 47 or
48, which are reserved for the Garage Door
operation. The 5816 is enrolled as loop 2 and 5822T
as Loop 3.
Installation Guide Part Number
800-10614V1 or higher (L5100/L5100CN)
800-16082 or higher (L5200/L7000 &
L5200CN/L7000CN)
Programming Guide Part Number
800-13468 or higher (L5100)
800-11060V1 (or higher) (L5100CN)
800-16085 or higher (L5200/L7000)
800-16086 or higher (L5200CN/L7000CN)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
