Honeywell D896- Manuals

D896 AUTOMATIC VENT DAMPER 68-0186 5 Fig. 3. Installing D896 Vent Damper. IMPORTANT Never mount the vent damper with the motoractuator above or below the vent. Do not install the damper blade plug if the vent damper is installed on a system with a continuous or standing pilot. Thehole provides the m...

D896 AUTOMATIC VENT DAMPER 68-0186 7 MV MV/PV PV GND(BURNER) 24VGND 24V SPARK S8600F, H, M; S8610F,H POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. REMOVE PLUG ONLY IF USING VENT DAMPER. FUSE BLOWS ON STARTUP WHEN PLUG IS REMOVED; THEN MODULE OPERATES ONLY WHEN VENT DAMP...

D896 AUTOMATIC VENT DAMPER 68-0186 8 Fig. 10. Snap-Tite™ Box Connector release. Checkout Heating 1. Turn on the power supply.2. If using a thermostat, set the heat anticipator at 0.13A.3. Set the thermostat or controller to 10 ° F (6 ° C) above the room temperature to call for heat. 4. Check that th...

D896 AUTOMATIC VENT DAMPER 68-0186 9 Thermostat Setting Symptom Possible Cause Action Set thermostat 10°Fabove room temperatureto call for heat. No response from D896. Incorrect wiring or blownfuse. • Check the circuit breaker or fuse and,if necessary, reset or replace. • Check the transformer and l...

D896 AUTOMATIC VENT DAMPER 68-0186 10 ANSI STANDARDS EXHIBIT A Procedure For Safety Inspection of an Existing Appliance Installation The following procedure is intended as a guide to aid indetermining that an appliance is properly installed and is in asafe condition for continuing use. This procedur...

D896 AUTOMATIC VENT DAMPER 68-0186 5 Fig. 3. Installing D896 Vent Damper. IMPORTANT Never mount the vent damper with the motoractuator above or below the vent. Do not install the damper blade plug if the vent damper is installed on a system with a continuous or standing pilot. Thehole provides the m...

D896 AUTOMATIC VENT DAMPER 68-0186 7 MV MV/PV PV GND(BURNER) 24VGND 24V SPARK S8600F, H, M; S8610F,H POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. REMOVE PLUG ONLY IF USING VENT DAMPER. FUSE BLOWS ON STARTUP WHEN PLUG IS REMOVED; THEN MODULE OPERATES ONLY WHEN VENT DAMP...

D896 AUTOMATIC VENT DAMPER 68-0186 8 Fig. 10. Snap-Tite™ Box Connector release. Checkout Heating 1. Turn on the power supply.2. If using a thermostat, set the heat anticipator at 0.13A.3. Set the thermostat or controller to 10 ° F (6 ° C) above the room temperature to call for heat. 4. Check that th...

D896 AUTOMATIC VENT DAMPER 68-0186 9 Thermostat Setting Symptom Possible Cause Action Set thermostat 10°Fabove room temperatureto call for heat. No response from D896. Incorrect wiring or blownfuse. • Check the circuit breaker or fuse and,if necessary, reset or replace. • Check the transformer and l...

D896 AUTOMATIC VENT DAMPER 68-0186 10 ANSI STANDARDS EXHIBIT A Procedure For Safety Inspection of an Existing Appliance Installation The following procedure is intended as a guide to aid indetermining that an appliance is properly installed and is in asafe condition for continuing use. This procedur...