Honeywell Central Heating Cooker Natural Gas- Manuals

6 The Redfyre cooker has two large ovens. The main ovenworks similar to a conventional oven which is controlled byits own programmer and thermostat, this thermostat alsocontrols the rest of the appliance. This oven will reach aroasting oven temperature in approximately 20 - 25 minutesfrom cold and l...

7 USERS INSTRUCTIONS COOKER BURNER 5.1 The cooker burner is fully automatic and requires no manual intervention to light. Ensure that the programmer is in theON mode, neon glowing, and turn the thermostat to thedesired temperature. The cooker light will illuminate and oncethe desired temperature has...

8 USER INSTRUCTIONS Setting event times Step A 6.7 Press PROG to advance to the next step. The display will be as in diagram 4. Step B 6.8 Press and release the+ or - buttons to change event 1 ON time in increments of one minute.Note: If buttons are held down, the time will change inincrements of 10...

9 USER INSTRUCTIONS 9.1 This is a blocked flue sensing device. This is an important safety device to prevent the products of combustion enteringthe room due to a flue problem. Under no circumstancesmust this device be put out of operation whilst the cooker isin use. 9.2 If either one or both burners...

10 OVEN COOKING GUIDE PLEASE NOTE - THESE TABLES SHOULD BE USED AS GUIDENCEONLY AS EACH COOKER AND ITS INSTALLATION WILL VARYSLIGHTLY. 1.1 Meat cooked in a heat storage cooker has very little shrinkage and rarely requires any additional fat for cooking. There aretwo basic methods for roasting meat, ...

12 CARE OF THE COOKER IMPORTANT: Never use caustic, citric, or abrasive cleaners as these will scratch ordamage the surface. Always try to wipe up any spillages when they occur. A more satisfactory result will be achieved if the cooker is coolwhen cleaning. Use hot soapy water and a cloth for the en...

13 USER COOKER FAULT FINDING COOKER WILL NOT START CHECK THE FUSE IN COOKER & BOILER MAINS SUPPLY HAS NOT BLOWN CHECK COOKER THERMOSTAT IS SWITCHED ON AMBER NEON WILL BE ILLUMINATED IS THE COOKER PROGRAMMER SWITCHED ON (NOTE PROGRAMMER WILL ‘GO TO SLEEP’ IF POWER SUPPLY HAS BEEN INTERRUPTED FOR ...

14 USER BOILER FAULT FINDING BOILER WILL NOT WORK SET EXTERNAL PROGRAMMER IS THE BOILER HIGH LIMIT RESET NEON ILLUMINATED ON THE CONTROL PANEL PRESS RESET BUTTON - (DO NOT RESET MORE THAN TWICE IF FAULT PERSISTS CALL YOUR ENGINEER) IF BOTH BOILER & COOKER RESET BUTTONS ARE ILLUMINATED IT MAY BE ...

16 TECHNICAL DETAILS Model Cooker 60 80 100 120 Rated input kw (gross) 17.6 22.2 29.7 37.3 45.5 Rated output kw (gross) - 17.6 23.4 29.3 35.2 Burner Cooker Boiler - 60k Boiler - 80k Boiler - 100k Boiler - 120k Gas Volume m 3/jr 1.68 2.11 2.84 3.56 4.34 Co2 % 8.5-9.0 7.0-8.0 8.0-8.5 8.5-9.0 8.5-9.0 S...

17 SITE REQUIREMENTS Sound Levels Whilst the level of sound is low it is important that the followingaspects should be considered before installation: (a) The Flue pipe from the appliance should be cast iron (b) Some people are particularly sensitive to even low noise levels so this aspect should be...

18 SITE REQUIREMENTS 51 87 126 167 206 70 158 604 1440clearance,(Min.) 985 915 970 125 FLOW and RETURNtappings1 ” BSP CENTRAL HEATING COOKER DIMENSIONS Gas Electric 1 4

19 INSTALLATION INSTRUCTIONS 1.1 The Redfyre range of Central Heating cookers is a range of floor mounted storage central heating cookers with a fixedrate cooker burner and the option of four fixed rate centralheating outputs depending on heating load. 60, 80, 100 x12,000 BTU. 1.2 The cooker has two...

20 INSTALLATION 1.1 The supply pipe from the cooker is 3/4” BSP threaded male. An isolating gas valve must be fitted adjacent to the cooker andthe gas installation pipe work must be installed, inspected,tested for soundness and purged in accordance with BS 6891 Nominal inlet gas pressure 20mbar Maxi...

INSTALLATION 21 4.1 Before using any existing chimney or refitting a gas appliance, it is vital to check that the chimney is safe. Oversized,leaking or rough chimneys can be inefficient and dangerous. 4.2 There are two basic existing types of chimney re-lining product suitable for use with gas appli...

22 FLUE SYSTEMS W I N D H I G H L O W H I G H L O W H I G H L O W R O O F P I T C H O V E R 3 0° R O O F P I T C H O V E R 3 0° F L A T R O O F 5. WIND EFFECTS ON BUILDINGS 6. IMPORTANT NOTES The following drawing shows the general high and lowpressure areas on buildings. Flues should not be termina...

23 FLUE TERMINATION I R R E S P E C T I V E O F T H E T Y P E S O F C H I M N E YS Y S T E M , A B R I T I S H G A S A P P R O V E D T E R M I N A LM U S T B E U S E D R e c o m m e n d e d f l u e p o s i t i o n s f o r s o m e r o o f c o n d i t i o n s

24 WATER SYSTEMS 1.1 The appliance is suitable for fully pumped open vent & sealed systems only and the installation must comply with the requirements of BS 6798 and BS 5449. Fit a drain off cock inthe lowest part of the system. Where the boiler is also to beused for providing domestic hot water...

27 ELECTRICAL SUPPLY Electrical Supply230V 1 Phase 50Hz (Fused 3 amp) Note: THIS APPLIANCE MUST BE EARTHED All electrical wiring must be carried out by a qualified electrician inaccordance with current I.E.E. Regulations and any LocalRegulations that may apply. The 230v - 50Hz electrical supply to t...

29 WIRING ‘S’ PLAN Independent control or space and water heating circulation in afully pumped system with two motorised valves (see SystemDiagrams 1 and 2) This scheme provides the optimum degree of control over a fullypumped installation. Seperate two port motorised valves are fittedin the space h...

30 WIRING ‘Y’ PLAN Independent control of space and water heating circulation inafully pumped system with one motorised diverting valve (SeeSystem Diagram 3) This scheme provides control over a fully pumped instalation bymeans of a single motorised diverting valve. This provides flow tothe space hea...

31 SERVICING To maintain the appliances high thermal efficiency andreliable operation, it must be serviced annually which is also arequirement of the appliances guarantee. If the boiler is usedto provide central heating and hot water, we recommendthat the appliances annual service is carried out jus...

33 SERVICING a) Remove the upper programmer retaining panel, four screw and starlock washers at the four corners of panel. b) Supporting the panel ease forward and release 6 way plug (two lugs). Carefully put panel at one side. c) Access to the underside of the control panel will need to be gained b...

34 SERVICING f) Replace in reverse order ensure heat shield large opening is at the top of the panel. g) Reset the programmer to the current time and program to customer requirements. See Fig. 11 a) Remove the lower control panel and remove the smaller blocked flue thermostat panel 2 screws. b) Remo...

35 SERVICING The boiler access door is behind the programmer mounting panel. Carefully remove the programmer mounting panel secured with fixing screws and disconnect the electrical plug. Remove the boiler access door by unscrewing the 4 wing nuts - check rubber seal and renew if necessary. Remove th...

36 SERVICE ENGINEER GUIDE TO FAULT FINDING NO CHECK OPERATION OF LIMIT THERMOSTAT AND NEON INDICATOR NO IS THERE 230V ON TERMINAL OF MAINS INLET PLUG IS THERE 230V ON TERMINAL L OF COOKER PROGRAMMER IS THERE 230V ON BLACK WIRE (SWITCH LIVE) FROM PROGRAMMER IS THERE 230V ON BLACK WIRE ON COOKER LIMIT...

37 SERVICE ENGINEER GUIDE TO FAULT FINDING IS THERE 230V ON TERMINAL S3 OF MAINS INLET PLUG IS THERE 230V ON TERMINAL 2 OF BOILER STAT (RED WIRE) IS THERE 230V ON TERMINAL ON BOILER LIMIT WITH RED AND PURPLE WIRE. CHECK FUNCTION OF BOILER LIMIT THERMOSTAT (CHECK FUNCTION OF OVERHEAT INDICATOR LIGHT)...

38 FAULT FINDING ELECTRICITY SAFETY - Switch off electrical supply to unit before making any electrical tests. FAULT POSSIBLE CAUSE ACTION BURNER WILL NOT START Boiler Thermostat or other Ensure all controls are calling for heat system controls satisfied Fuse blown Fit new 5 amp fuse, if it blows ag...

40 SPARE PARTS LIST Item Description Part No. 1 Door Catch Chrome R/H 602884 2 Door Catch Chrome L/H 602883 3 Door Seal 602911 4 Spring 602088 5 Hinge pin 33097 6 Buffer 99593 7 Enamelled Door Liner 602912 8 Towel Rail chrome 600841 9 Chrome Lid 602457 10 Spring Handle 601478 11 Inner Lid 602459 12 ...

6 The Redfyre cooker has two large ovens. The main ovenworks similar to a conventional oven which is controlled byits own programmer and thermostat, this thermostat alsocontrols the rest of the appliance. This oven will reach aroasting oven temperature in approximately 20 - 25 minutesfrom cold and l...

7 USERS INSTRUCTIONS COOKER BURNER 5.1 The cooker burner is fully automatic and requires no manual intervention to light. Ensure that the programmer is in theON mode, neon glowing, and turn the thermostat to thedesired temperature. The cooker light will illuminate and oncethe desired temperature has...

8 USER INSTRUCTIONS Setting event times Step A 6.7 Press PROG to advance to the next step. The display will be as in diagram 4. Step B 6.8 Press and release the+ or - buttons to change event 1 ON time in increments of one minute.Note: If buttons are held down, the time will change inincrements of 10...

9 USER INSTRUCTIONS 9.1 This is a blocked flue sensing device. This is an important safety device to prevent the products of combustion enteringthe room due to a flue problem. Under no circumstancesmust this device be put out of operation whilst the cooker isin use. 9.2 If either one or both burners...

10 OVEN COOKING GUIDE PLEASE NOTE - THESE TABLES SHOULD BE USED AS GUIDENCEONLY AS EACH COOKER AND ITS INSTALLATION WILL VARYSLIGHTLY. 1.1 Meat cooked in a heat storage cooker has very little shrinkage and rarely requires any additional fat for cooking. There aretwo basic methods for roasting meat, ...

12 CARE OF THE COOKER IMPORTANT: Never use caustic, citric, or abrasive cleaners as these will scratch ordamage the surface. Always try to wipe up any spillages when they occur. A more satisfactory result will be achieved if the cooker is coolwhen cleaning. Use hot soapy water and a cloth for the en...

13 USER COOKER FAULT FINDING COOKER WILL NOT START CHECK THE FUSE IN COOKER & BOILER MAINS SUPPLY HAS NOT BLOWN CHECK COOKER THERMOSTAT IS SWITCHED ON AMBER NEON WILL BE ILLUMINATED IS THE COOKER PROGRAMMER SWITCHED ON (NOTE PROGRAMMER WILL ‘GO TO SLEEP’ IF POWER SUPPLY HAS BEEN INTERRUPTED FOR ...

14 USER BOILER FAULT FINDING BOILER WILL NOT WORK SET EXTERNAL PROGRAMMER IS THE BOILER HIGH LIMIT RESET NEON ILLUMINATED ON THE CONTROL PANEL PRESS RESET BUTTON - (DO NOT RESET MORE THAN TWICE IF FAULT PERSISTS CALL YOUR ENGINEER) IF BOTH BOILER & COOKER RESET BUTTONS ARE ILLUMINATED IT MAY BE ...

16 TECHNICAL DETAILS Model Cooker 60 80 100 120 Rated input kw (gross) 17.6 22.2 29.7 37.3 45.5 Rated output kw (gross) - 17.6 23.4 29.3 35.2 Burner Cooker Boiler - 60k Boiler - 80k Boiler - 100k Boiler - 120k Gas Volume m 3/jr 1.68 2.11 2.84 3.56 4.34 Co2 % 8.5-9.0 7.0-8.0 8.0-8.5 8.5-9.0 8.5-9.0 S...

17 SITE REQUIREMENTS Sound Levels Whilst the level of sound is low it is important that the followingaspects should be considered before installation: (a) The Flue pipe from the appliance should be cast iron (b) Some people are particularly sensitive to even low noise levels so this aspect should be...

18 SITE REQUIREMENTS 51 87 126 167 206 70 158 604 1440clearance,(Min.) 985 915 970 125 FLOW and RETURNtappings1 ” BSP CENTRAL HEATING COOKER DIMENSIONS Gas Electric 1 4

19 INSTALLATION INSTRUCTIONS 1.1 The Redfyre range of Central Heating cookers is a range of floor mounted storage central heating cookers with a fixedrate cooker burner and the option of four fixed rate centralheating outputs depending on heating load. 60, 80, 100 x12,000 BTU. 1.2 The cooker has two...

20 INSTALLATION 1.1 The supply pipe from the cooker is 3/4” BSP threaded male. An isolating gas valve must be fitted adjacent to the cooker andthe gas installation pipe work must be installed, inspected,tested for soundness and purged in accordance with BS 6891 Nominal inlet gas pressure 20mbar Maxi...

INSTALLATION 21 4.1 Before using any existing chimney or refitting a gas appliance, it is vital to check that the chimney is safe. Oversized,leaking or rough chimneys can be inefficient and dangerous. 4.2 There are two basic existing types of chimney re-lining product suitable for use with gas appli...

22 FLUE SYSTEMS W I N D H I G H L O W H I G H L O W H I G H L O W R O O F P I T C H O V E R 3 0° R O O F P I T C H O V E R 3 0° F L A T R O O F 5. WIND EFFECTS ON BUILDINGS 6. IMPORTANT NOTES The following drawing shows the general high and lowpressure areas on buildings. Flues should not be termina...

23 FLUE TERMINATION I R R E S P E C T I V E O F T H E T Y P E S O F C H I M N E YS Y S T E M , A B R I T I S H G A S A P P R O V E D T E R M I N A LM U S T B E U S E D R e c o m m e n d e d f l u e p o s i t i o n s f o r s o m e r o o f c o n d i t i o n s

24 WATER SYSTEMS 1.1 The appliance is suitable for fully pumped open vent & sealed systems only and the installation must comply with the requirements of BS 6798 and BS 5449. Fit a drain off cock inthe lowest part of the system. Where the boiler is also to beused for providing domestic hot water...

27 ELECTRICAL SUPPLY Electrical Supply230V 1 Phase 50Hz (Fused 3 amp) Note: THIS APPLIANCE MUST BE EARTHED All electrical wiring must be carried out by a qualified electrician inaccordance with current I.E.E. Regulations and any LocalRegulations that may apply. The 230v - 50Hz electrical supply to t...

29 WIRING ‘S’ PLAN Independent control or space and water heating circulation in afully pumped system with two motorised valves (see SystemDiagrams 1 and 2) This scheme provides the optimum degree of control over a fullypumped installation. Seperate two port motorised valves are fittedin the space h...

30 WIRING ‘Y’ PLAN Independent control of space and water heating circulation inafully pumped system with one motorised diverting valve (SeeSystem Diagram 3) This scheme provides control over a fully pumped instalation bymeans of a single motorised diverting valve. This provides flow tothe space hea...

31 SERVICING To maintain the appliances high thermal efficiency andreliable operation, it must be serviced annually which is also arequirement of the appliances guarantee. If the boiler is usedto provide central heating and hot water, we recommendthat the appliances annual service is carried out jus...

33 SERVICING a) Remove the upper programmer retaining panel, four screw and starlock washers at the four corners of panel. b) Supporting the panel ease forward and release 6 way plug (two lugs). Carefully put panel at one side. c) Access to the underside of the control panel will need to be gained b...

34 SERVICING f) Replace in reverse order ensure heat shield large opening is at the top of the panel. g) Reset the programmer to the current time and program to customer requirements. See Fig. 11 a) Remove the lower control panel and remove the smaller blocked flue thermostat panel 2 screws. b) Remo...

35 SERVICING The boiler access door is behind the programmer mounting panel. Carefully remove the programmer mounting panel secured with fixing screws and disconnect the electrical plug. Remove the boiler access door by unscrewing the 4 wing nuts - check rubber seal and renew if necessary. Remove th...

36 SERVICE ENGINEER GUIDE TO FAULT FINDING NO CHECK OPERATION OF LIMIT THERMOSTAT AND NEON INDICATOR NO IS THERE 230V ON TERMINAL OF MAINS INLET PLUG IS THERE 230V ON TERMINAL L OF COOKER PROGRAMMER IS THERE 230V ON BLACK WIRE (SWITCH LIVE) FROM PROGRAMMER IS THERE 230V ON BLACK WIRE ON COOKER LIMIT...

37 SERVICE ENGINEER GUIDE TO FAULT FINDING IS THERE 230V ON TERMINAL S3 OF MAINS INLET PLUG IS THERE 230V ON TERMINAL 2 OF BOILER STAT (RED WIRE) IS THERE 230V ON TERMINAL ON BOILER LIMIT WITH RED AND PURPLE WIRE. CHECK FUNCTION OF BOILER LIMIT THERMOSTAT (CHECK FUNCTION OF OVERHEAT INDICATOR LIGHT)...

38 FAULT FINDING ELECTRICITY SAFETY - Switch off electrical supply to unit before making any electrical tests. FAULT POSSIBLE CAUSE ACTION BURNER WILL NOT START Boiler Thermostat or other Ensure all controls are calling for heat system controls satisfied Fuse blown Fit new 5 amp fuse, if it blows ag...

40 SPARE PARTS LIST Item Description Part No. 1 Door Catch Chrome R/H 602884 2 Door Catch Chrome L/H 602883 3 Door Seal 602911 4 Spring 602088 5 Hinge pin 33097 6 Buffer 99593 7 Enamelled Door Liner 602912 8 Towel Rail chrome 600841 9 Chrome Lid 602457 10 Spring Handle 601478 11 Inner Lid 602459 12 ...