Honeywell 5207 - Manuals

150865 2-1 Section 2Agency Listings and Requirements 2.1 Federal Communications Commission (FCC) 1. If requested by the telephone company, the following information must be provided before the 5207 can be connected to the phone lines: 2. This device may not be directly connected to coin telephone or...

Model 5207 Fire Control/Communicator Installation and Operation Manual 2-2 150865 2.2 Underwriters Laboratories (UL) The 5207 is UL Listed as a control unit for use in Central Station Fire-Protective Signaling systems. If the 5207 and its accessories are to be used as part of a UL installation, care...

Agency Listings and Requirements 150865 2-3 2.2.3 Requirements for Auxiliary Protected Fire Alarm Systems for Fire Alarm Service 1. Follow the current load restrictions shown in Section 3.5. 2. The Model 5220 Direct Connect module must be installed (see Section 4.7 for wiring). 2.2.4 Requirements fo...

150865 3-1 Section 3Control Panel Installation 3.1 Electrical Specifications 3.2 Environmental Specifications It is important to protect the 5207 control panel from water. To prevent water damage, the fol-lowing conditions should be AVOIDED when mounting the units: ï Do not mount directly on exterio...

Model 5207 Fire Control/Communicator Installation and Operation Manual 3-2 150865 3.3 Wiring Specifications To avoid induced noise (transfer of electrical energy from one wire to another), keep input wiring isolated from high current output and power wiring. Induced noise can interfere with telephon...

Control Panel Installation 150865 3-3 3.4 Model 5207 Wiring Diagram Figure 3-2 is a wiring diagram for wiring the Model 5207 panel. Figure 3-2 Model 5207 Wiring Reference

Model 5207 Fire Control/Communicator Installation and Operation Manual 3-4 150865 3.5 Current Draw Worksheet Table 3-2 Current Draw Worksheet Device Number of Devices Current per Device Standby Current Alarm Current For each device, use this formula: This column X This column = Current per number of...

Control Panel Installation 150865 3-5 3.5.1 Worksheet Example The Current Draw worksheet is included to help you calculate the amount of current the sys-tem draws on standby and in an alarm condition. Refer to Table 3-4 for available battery sizes and the maximum standby current load each can suppor...

Model 5207 Fire Control/Communicator Installation and Operation Manual 3-6 150865 3.5.2 Worksheet Requirements The following steps must be taken when determining Model 5207 current ratings: 1. Measure the alarm current. If only one current rating is listed, the draw for that device is the same wheth...

Control Panel Installation 150865 3-7 Figure 3-4 Battery Calculation Example 5. Refer to to verify the battery size you need to provide at least the total standby current you have calculated. If the installation must meet requirements for NFPA 72 (Auxiliary Pro-tected Fire Alarm Systems for Fire Ala...

Model 5207 Fire Control/Communicator Installation and Operation Manual 3-8 150865 3.6 Power Supply Wiring The Model 5198 power supply delivers 24 VDC at 5A for loop power, smoke detector power, notification device power, and accessory power. The Model 6914 is a 12-Volt, 17-AH battery. Figure 3-5 sho...

Model 5207 Fire Control/Communicator Installation and Operation Manual 3-10 150865 3.8 Terminal Strip Description The terminal strips on the PC board are nonremovable. Table 3-5 on the next page lists the function and electrical rating of each terminal. See Section 3.4 for the wiring diagram. Table ...

Model 5207 Fire Control/Communicator Installation and Operation Manual 3-12 150865 3.9 Telephone Line Connection The 5207 connects to two separate telephone lines to report data to the central station. An RJ31X jack should be installed by the telephone company for each line. Figure 3-6 shows how to ...

Control Panel Installation 150865 3-13 3.10 Cable Connectors Power Supply Connector (P1) Connects the 5207 control panel to the 5198 power supply. Model 5210 (P2) Connects the 5210 zone expander to the 5207. Quick Connect (P3) For temporarily connecting a 5230 for programming or troubleshooting. Req...

Compatible Product Installation 150865 4-3 4.3 Four-Wire Smoke Detector Connection Figure 4-3 illustrates how UL listed four-wire smoke detectors must be connected to class B (style A) zones. When wiring a four-wire smoke detector to the class B (style A) zones, you must use a Power Supervision Unit...

Model 5207 Installation and Operation Manual 4-4 150865 4.4 Two-Wire Smoke Detector Connection Figure 4-4 shows how to connect two-wire smoke detectors to class B (style A) zones. Figure 4-4 Two-Wire Smoke Detector Wiring See Appendix A for a list of two-wire smoke detectors that may be used with th...

Compatible Product Installation 150865 4-5 Wire the 4180 as shown in Figure 4-5. Make sure power is OFF at the panel before plugging in the 4180. Maintain a physical separation of one-half inch or more between field wires and connection points to prevent damage from transients. Note: SILENCE does no...

Model 5207 Installation and Operation Manual 4-6 150865 4.6 Model 5210 Zone Expander Wiring The Model 5210 provides the 5207 with eight additional class B (style A) zones. Figure 4-6 shows how to wire the 5210. Use a 4.7k end of line resistor for each class B loop. The EOL must be wired in parallel ...

Compatible Product Installation 150865 4-7 4.7 Model 5220 Direct Connect Module The 5220 Direct Connect module can be used with the 5207 to meet NFPA 72 standards. The 5220 requires four connections to the 5207 and provides outputs for city box and polarity reversal applications. The 5220 cannot be ...

Model 5207 Installation and Operation Manual 4-8 150865 4.7.2 NFPA 72 Polarity Reversal When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator...

Compatible Product Installation 150865 4-9 4.8 Keltron 95M3158 Tones Transmitter Module This section of the manual shows the specific connections you will make when wiring the 5207 to the Keltron 95M3158 Tones Transmitter Module (3158). Refer to the installation sheet shipped with the 95M3158 for co...

Model 5207 Installation and Operation Manual 4-10 150865 4.9 Model 5230 Remote Annunciator The 5230 performs all system operation. It also provides trouble and alarm information and can be used for programming. 4.9.1 Setting ID Codes Before permanently installing the Model 5230 Remote Annunciator, y...

Model 5207 Installation and Operation Manual 4-12 150865 4.9.3 Mounting the 5230 Remote Annunciator For UL installations, the 5230 Remote Annunciators must be mounted on a dual gang electri-cal box and all wiring runs must be made using 18-gauge wire or larger. To mount the annunciator: 1. Remove th...

Model 5207 Installation and Operation Manual 4-14 150865 4.11 Model 7181 Zone Converter The Model 7181 Zone Converter lets you interchange zone types on the 5207. Figure 4-13 and Figure 4-14 show how to make conversions. Refer to the Model 7181 Installation Manual (P/N 150632) for complete informati...

Compatible Product Installation 150865 4-15 4.12 Supervised Notification Appliance Outputs Note: To reduce the possibility of false alarms and transient damage, DO NOT bundle telephone wires together with notification circuit wires. The 5207 provides four supervised notification circuit outputs to a...

Model 5207 Installation and Operation Manual 4-16 150865 4.13 Auxiliary Relays The 5207 provides four programmable auxiliary relay outputs. Relays can be programmed to activate for the following conditions, either for all zones or by individual zone: pre-alarm (entry delay) (not acceptable for NFPA ...

150865 5-1 Section 5Operation To operate the 5207 you can use either the built-in touchpad or the Model 5230 Remote Annunciator. Figure 5-1 Built-in Touchpad (Seven-Segment Display) Figure 5-2 Model 5230 Remote Annunciator

Model 5207 Fire Control/Communicator Installation and Operation Manual 5-2 150865 5.1 Built-in Touchpad and Model 5230 Operation Basic operation of both the 5230 and the built-in touchpad is described in Table 5-1. Note that if no keys are pressed for 15 minutes while in program mode, the system wil...

Model 5207 Fire Control/Communicator Installation and Operation Manual 5-4 150865 5.1.1 Built-in Touchpad Display Codes The following table briefly describes the codes that are displayed on the built-in touchpad. For complete information and for 5230 display messages, see Section 9. Table 5-2 Built-...

Operation 150865 5-5 5.1.2 LED Indicators Six light emitting diodes (LEDs) appear in the 5207 cabinet window. The chart below explains the meaning of these LEDs. 5.2 System Testing This section describes operation of fire drills, zone testing, and the 24-hour automatic test. 5.2.1 Fire Drills Fire d...

Model 5207 Fire Control/Communicator Installation and Operation Manual 5-6 150865 5.2.2 Walk Test (Mode 22) The walk test is designed to be used for onsite testing only. To enter walk test mode, press + code 0 or 1. The LCD will indicate that you are in walk test mode. When a zone is tripped, the 52...

150865 6-1 Section 6Programming: Quick Reference This section of the manual briefly describes all available programming options and lists the factory programmed default values. Section 7 of this manual is a complete, step-by-step guide that provides details, including LCD diagrams, of each programmi...

150865 7-1 Section 7 Programming: Step-by-Step Complete Reference The Model 5230 Remote Annunciator is for programming the 5207 panel. You must be in Step Programming Mode (also known as mode 27) to program the panel. See the following sections for details. 7.1 Using Step Programming Enter Step Prog...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-2 150865 Selecting Options Scrolling For most options, you enter numbers in the same way as if you were using a calculator. The digits appear on the right side of the display and scroll to the left as you continue to enter data...

Programming: Step-by-Step Complete Reference 150865 7-3 Programming Examples The following examples demonstrate how to use Step Programming. The selections you make in each installation will vary depending on each customerís needs. The way you move through Mode 27 may also vary from how it is descri...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-4 150865 7.2 Step Programming Options This section is organized in step order and provides complete instructions for each step. Step 1. Power Up Clear Step 2. Device Enables Display Description The two digits of this step are u...

Programming: Step-by-Step Complete Reference 150865 7-5 Step 3. More System Options Step 4. Display Rate Display Description Step 3 allows you to select seven system options shown below. To select an option, press its number. 0 = Cadenced pulsing of bells. If you select this option, bells will pulse...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-6 150865 Step 5. Miscellaneous Options Step 6. Internal Zone Options Display Description Step 5 is for programming several system options, including bell supervision. 0 = Walk tests will be reported. Select this option if you w...

Programming: Step-by-Step Complete Reference 150865 7-7 Programming Zone Response Time (Steps 6.5 & 6.6) There are four possible response times. To program the response times, select the zone number that should have that response time in Steps 6.5 and 6.6, as follows: Normally Open zones  Zones...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-8 150865 Example : To program an 8-zone installation where you want loop response speeds to be as follows: Zone 1: 0.094 - 0.125 sec.Zones 2-5: 3-4 sec.Zones 6-7: 15-20 sec.Zone 8: 30-40 sec. Do This: In Step 6.5, select zones ...

Programming: Step-by-Step Complete Reference 150865 7-9 Step 7. External Zone Options Display Description 24 Hour alarm  Zones will be active 24 hours. Must be selected for all zones. Do NOT change the factory programming for this step . Trouble supervised  For zones 9 to 16, enter the number of z...

Programming: Step-by-Step Complete Reference 150865 7-11 Step 10. Total Number of Attempts Step 11. Number of Events Before Dialer Failed Step 12. Low AC Hours Step 13. Number of Rings Display Description Total number of attempts to dial. Select a number from 5 to 15. For a local- only system, selec...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-12 150865 Step 14. Report to Telephone Numbers Display Description The phone number to which alarms should be reported. Select 1-4 for phone numbers 1-4. 1 = Report alarms to phone number 12 = Report alarms to phone number 23 =...

Programming: Step-by-Step Complete Reference 150865 7-13 Step 15. Computer Phone Number Step 16. Central Station Phone Numbers Step 17. Central Station Account Numbers Display Description Enter the phone number the system will dial to up- or download system data. Entering Phone Numbers Phone numbers...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-14 150865 Step 18. Dialer Format and Number of Attempts Step 19. Telephone Line to Use for Accounts Display Description Digit 1 = Enter the number of attempts for account number 1. This number is how many times the dialer will ...

Programming: Step-by-Step Complete Reference 150865 7-15 Step 20. Duration of Delays Display Description Bell Shutdown Time (1-255) Divide by 10 and enter the number indicating the time that you want audio alarms to be active. Example: Suppose you want audio alarms to be active for 900 seconds (or 1...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-16 150865 Step 21. Test Time Step 22. Secret Codes Display Description Enter time that automatic daily test should occur using 24-hour military time. Enter 6 digits with leading zeros. Examples: To program the daily test to occ...

Programming: Step-by-Step Complete Reference 150865 7-17 Step 23. Group Relays and Bells IMPORTANT: You can program relays and bells in either the Group section (Step 23) or the By Zone section (Step 24), but not both. Relays and bells are programmed for the type of condition that causes them to act...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-18 150865 Display Description Step 23 continued 2. Fire condition relays/bells are programmed in Step 23.4. a. Press to select Bell 1 b. Press to select Bell 2 c. Press to select Bell 3 d. Press to select Bell 4 Your LCD would ...

Programming: Step-by-Step Complete Reference 150865 7-19 Step 24. Alarm Relays and Bells (by Zone) Display Description Trouble Relays and Bells 1-4 = Relays that activate during a trouble condition.5-8 = Bells that activate during a trouble condition. Note: Relays or bells selected as Trouble will n...

Programming: Step-by-Step Complete Reference 150865 7-21 Step 26. Zone Location Descriptions Display Description The following instructions explain how to select zone descriptions for the 5230 display . For Steps 26.1-26.16, the factory-programmed default is ì WORDSî (ì WORDSî appears on the LCD). Y...

Model 5207 Fire Control/Communicator Installation and Operation Manual 7-22 150865 Steps 27 and 28. Temporal Patterns Display Description This step programs the length of the pattern. Steps 27 and 28 are used together to control the temporal (pulsing) pattern of the bell outputs. You can use these s...

Programming: Step-by-Step Complete Reference 150865 7-23 Display Description This step selects the actual pattern. Steps 28.1-28.4 determine the pattern. Select a digit for each half-second ON; de-select a digit (display shows a dash) for each half-second OFF. Each sub-step controls up to four secon...

150865 8-1 Section 8Reporting The following formats can be used to report to Silent Knight receivers and are explained fur-ther in this section: ï SIA ï FSK & SK 4+2 ï 16 Zone 4+2 ï Radionics BFSK The following Trouble Conditions may generate a report to the central station: ï Low AC ï Low batte...

Model 5207 Fire Control/Communicator Installation and Operation Manual 8-2 150865 8.2 SIA Format Printed Messages The Security Industry Association (SIA) format can be used with a Silent Knight Model 9000 receiver. Each message is displayed in English followed by the zone number. Due to limited spac...

Model 5207 Fire Control/Communicator Installation and Operation Manual 8-4 150865 8.3 FSK & SK 4+2 Format You must use either the FSK or SK 4+2 format when reporting to the Silent Knight Model 8520 Receiver. Since the 8520 has only two digits for alarm codes, event type and zone num-bers are com...

Model 5207 Fire Control/Communicator Installation and Operation Manual 8-6 150865 8.5 Radionics BFSK Format Model 5207 can transmit using the Radionics BFSK format with 1400 Hz or 2300 Hz acknowledge. The messages that will be printed are listed with the codes for FSK1 and SK 4+2. Radionics BFSK for...

150865 9-1 Section 9Troubleshooting 9.1 Problems With the Model 5198 Power Supply If you experience problems with the power supply, use the troubleshooting techniques described in the following sections. There are separate procedures for 12-volt and 24-volt power supplies. The following display mess...

Model 5207 Fire Control/Communicator Installation and Operation Manual 9-2 150865 9.2 P3 and P4 Earth Ground Faults A P3 trouble indicates that the panel has detected a short between earth ground (terminal 52) and circuit ground (terminals 1, 10, 20, 25). A P4 trouble indicates that the panel has de...

Troubleshooting 150865 9-3 When you momentarily put a zone into alarm, the touchpad will display the Present (current) value along with the High (spikes) and Low (voltage drop) values. This is also useful in locat-ing intermittent connections. Step numbers range from 0 to 16. Using Table 9-1, you ca...

Model 5207 Fire Control/Communicator Installation and Operation Manual 9-4 150865 9.4 Troubleshooting and System Messages Table 9-2 shows the messages that may appear on the Model 5230 Touchpad display and the codes that may appear on the 5207 built-in touchpad display. For troubleshooting, you can ...

150865 A-1 Appendix ACompatible Devices This section of the manual lists devices (smoke detectors and notification appliances) that are compatible with the 5207. Contact Silent Knight if you have a question about whether a device not listed here is compatible. A.1 Smoke Detectors This section of the...

Model 5207 Fire Control/Communicator Installation and Operation Manual A-2 150865 ESL 429CST (S11A) 30 / loop 14 / loop ESL 429CT (S10A) 30 / loop 14 / loop ESL 609U01-11 40 / loop 24 / loop ESL 609U02-11 40 / loop 24 / loop ESL 611U (601U or 602U) 40 / loop 24 / loop ESL 611UD (601U or 602U) 40 / l...

150865 A-3 Four Wire Smoke Detectors A.2 Notification Appliances The chart below lists notification appliances compatible with the 5207. System Sensor 2451 (B401B) 20 / loop 8 / loop System Sensor 2451DH (DH 400) 20 / loop 8 / loop System Sensor 2451TH (B401B) 20 / loop 8 / loop System Sensor 2800 2...

Sensing and ControlHoneywell1985 Douglas Drive NorthGolden Valley, MN 55422 honeywell.com 50045178-E-EN IL50 June 2015 © 2015 Honeywell International Inc. All rights reserved. Honeywell Zephyr TM Digital Airflow Sensors HAF Series–High Accuracy±50 SCCM to ±750 SCCM Issue E 50045178 WARRANTY/REMEDY H...