Henny Penny OFE- 291 - Manuals

Henny Penny OFE- 291 – Manual in PDF format online.

Manuals:

Manual

Manual Henny Penny OFE- 291

Summary

Page 2 - Model OFE- 291; High Limit; Lower the lid until latch comes into contact with the pot.

Model OFE- 291 3-1. OPERATING COMPONENTS (Continued) High Limit This high temperature control senses the temperature of theshortening; if the temperature of the shortening exceeds450°F (230°C), this control will open and shut off the heatto the frypot; when the temperature of the shortening dropsto ...

Page 3 - Refer to image at the end of this section.; INDICATORS; Digital Display

Model OFE- 291 3-3. SWITCHES AND Refer to image at the end of this section. INDICATORS Fig. Item Description Function No. No. 3-2 1 Lights when the control calls for heat; the elements come on andheats the shortening 3-2 2 Digital Display Shows all the functions of the Cook Cycle, Program Modes,Diag...

Page 4 - Item

Model OFE- 291 3-3. SWITCHES AND INDICATORS (Continued) Fig. Item Description Function No. No. 3-2 9 Press to access Program Modes; once in the Program Mode, itis used to advance to the next setting; if pressed along with it accesses the Information Mode which has historicinformation on the operator...

Page 8 - SHORTENING; Cold shortening should be filled to lower indicator.

Model OFE- 291 3-5. FILLING OR ADDING SHORTENING The shortening level must always be above the heatingelements when the fryer is heating and at the frypot levelindicators on the rear of the frypot (Figure 3-3). Failureto follow these instructions could result in a fire and/ordamage to the fryer. Whe...

Page 11 - Allow fryer to heat until illuminates.

Model OFE- 291 3-7. BASIC OPERATION 4. Allow fryer to heat until illuminates. (Continued) Bypass the melt cycle, if desired, by pressing a productbutton and holding it for five seconds. The display shows“EXIT MELT? 1=YES 2=NO”. Press to exit melt. Do not bypass the Melt Cycle unless enough shortenin...

Page 12 - Unlatch and raise the lid cautiously.

Model OFE- 291 3-7. BASIC OPERATION 8. Unlatch and raise the lid cautiously. (Continued) 9. Using the rack handles, remove the racks of product fromthe carrier, starting with the top rack, to prevent damagedproduct. 10. If a Quality time (hold time) was programmed, the controllerautomatically starts...

Page 13 - The Henny Penny electric 8 head fryer, Model 291, must be; INSTRUCTIONS

Model OFE- 291 3-8. CARE OF THE SHORTENING FOLLOW THE INSTRUCTIONS BELOW TO AVOIDSHORTENING OVERFLOWING THE FRYPOT,WHICH COULD RESULT IN SERIOUS BURNS,PERSONAL INJURY, FIRE, AND/OR PROPERTYDAMAGE. 1. To protect the shortening when the fryer is not in immediateuse, the fryer should be put into the Id...

Page 14 - Shortening Stirrer

Model OFE- 291 3-9. FILTERING INSTRUCTIONS (continued) FILTER ONLY WHEN THE SHORTENINGTEMPERATURE IS LESS THAN 275° F (135° C).FAILURE TO DO SO CAN RESULT IN SHORTEN-ING OVERFLOWING THE FRYPOT, CAUSINGSERIOUS BURNS, PERSONAL INJURY, AND/ORPROPERTY DAMAGE. High volume cooking could cause the cold zon...

Page 15 - a. Attach the filter rinse hose with its quick disconnect fitting

Model OFE- 291 3-9. FILTERING INSTRUCTIONS (Continued) BRUSH ALL CRACKLINGS FROM FRYPOTSURFACES AND THE COLD ZONE DURING THEFILTERING PROCESS. FAILURE TO DO SO CANRESULT IN SHORTENING OVERFLOWING THEFRYPOT, WHICH COULD CAUSE SERIOUSBURNS, PERSONAL INJURY, FIRE AND/ORPROPERTY DAMAGE. 5. When all of t...

Page 16 - ENVELOPE

Model OFE- 291 c. Rinse the frypot interior. Especially work on hard to clean areas, like the frypot bottom and burner tubes. d. After thorough rinsing with shortening, close the drain valve. e. Turn the COOK/PUMP switch to the OFF position. ONLY CONNECT AND DISCONNECT THE FILTERRINSE HOSE WHEN THE ...

Page 18 - The filter pump motor is equipped with a manual reset button,; PROTECTOR-MANUAL; located on the rear of the motor, in case the motor overheats. If; RESET

Model OFE- 291 3-11. FILTER PUMP MOTOR The filter pump motor is equipped with a manual reset button, PROTECTOR-MANUAL located on the rear of the motor, in case the motor overheats. If RESET motor won’t run, wait about 5 minutes before attempting to resetthis protective device to allow motor to cool....

Page 19 - If hot shortening is present in the frypot, it must be; Henny Penny has the following cleaners available:

Model OFE- 291 3-12. CLEANING THE FRYPOT 2. If hot shortening is present in the frypot, it must be (Continued) drained by slowly pulling the drain handle out towards you. 3. Close the drain valve and discard the shortening. 4. Raise lid, remove the racks and carrier from lid, and tilt lidback, so th...

Page 20 - Using the fryer brush (Henny Penny part number 12105)

Model OFE- 291 3-12. CLEANING THE FRYPOT 7. Using the fryer brush (Henny Penny part number 12105) (Continued) scrub the inside of the frypot, the lid, and aroundthe counter-top of the fryer. Watch the cleaning solution constantly to make sure itdoes not boil over causing damage to controls. Do not u...

Page 21 - Procedure

Model OFE- 291 3-13. REGULAR MAINTENANCE As in all food service equipment, the Henny Penny open fryer doesrequire care and proper maintenance. The table below provides asummary of scheduled maintenance. The following paragraphsprovide step-by-step maintenance procedures to be performed bythe operato...

Page 22 - Change Product Names

Model OFE- 291 3-15. PROGRAMMING Change Product Names (Continued) a. Press and release and the first letter, or digit, starts flashing. b. Press and release to change the flashing letter. c. To continue to the next letter, press . Then press to change this letter. d. Repeat step c until up to 7 lett...

Page 24 - Go to Idle after Done?

Model OFE- 291 11. Press and release and “LOAD COMP” shows in the display along with the load compensation value. Thisautomatically adjusts the time to account for the size andtemperature of the cooking load. Press and release to change this value to a max. of 20 and a min. of 0, or“OFF”. Preset at ...

Page 26 - for

Model OFE- 291 The following are examples of copying and erasing products:CopyingPress to select the presently displayed “COPY A PROD” option. “COPY __ TO __” shows in display. The first set of“_” is blinking. Select the product you wish to copy from , for example, by pressing the button: “COPY 2 TO...

Page 27 - MODE

Model OFE- 291 3-16. SPECIAL PROGRAM The Special Program mode is used to set more detailed MODE parameters listed below. SP-1 · Degrees Fahrenheit or Celsius SP-2 · Language: English, French, German, Spanish, and Portuguese SP-3 · System initialization SP-4 · Audio volume SP-5 · Audio tone SP-6 · Ty...

Page 29 - The Melt Cycle can be set to the type of shortening being used.

Model OFE- 291 Type of shortening to be melted - Liquid or Solid (SP-6) The Melt Cycle can be set to the type of shortening being used. a. Follow steps 1 and 2 above. b. Press and release 5 times. “SP-6” and “MELT CYCLE SELECT” flashes on the display,along with “l=LIQ” or “2=SOLID”. c. Press to togg...

Page 30 - MIXED

Model OFE- 291 3-16. SPECIAL PROGRAM e. Change the idle setpoint temperature, by pressing MODE (Continued) f. Press and release . “SP-7B” and “AUTO-IDLE MINUTES” shows in the display, alongwith the preset time. g. Press to set the minutes the cooker stays idle before the Auto-idle is enabled; 60 the...

Page 31 - GLOBAL

Model OFE- 291 3-16. SPECIAL PROGRAM f. Press and “SP-8C” shows in the display, if YES MODE (Continued) was chosen in step e. “FILTER LOCKOUT AT…” and avalue between 100% and 200% shows in display. Press to change this value. g. Press and “SP-8D” shows in the display, followed by “LOCKOUT-HEAT OIL.....

Page 32 - SCHEDULE

Model OFE- 291 1005 3-32 3-16. SPECIAL PROGRAM MODE (Continued) SCHEDULE m. If “4,SCHED” is selected, “SP-8A” shows in the display, and followed by “SCHEDULE”. Press the and up to 4 different times of day can be programmed, by pressing . . EX:SP-8A “SCHEDULE” F1: 10.00ASP-8B “SCHEDULE” F2: 2.00PSP-8...

Page 34 - shows in display. Press product buttons with new code.

Model OFE- 291 3-16. SPECIAL PROGRAM MODE (Continued) Program Code Change (SP-15) This allows the operator to change the program code (factoryset at 1, 2, 3) used to access Product Programming, SpecialProgramming, Clock Set, Data Comm, and Heat Control Modes. a. Follows steps 1 and 2 above. b. Press...

Page 35 - f. If not satisfied with code, press and; AND STAT MODE

Model OFE- 291 e. If satisfied with code, press . “*CODE CHANGE*” shows in display. f. If not satisfied with code, press and *CANCELLED* shows in display, then reverts back to “SP-16” and “CHANGE USG CODE ? 1=YES”. Thenthe above steps can be repeated. Change Shortening-A-Cook Cycles (SP-17) The oper...

Page 36 - Press to continue to LAST LOAD.

Model OFE- 291 3-18. INFORMATION MODE This mode gathers and stores historic information on the fryer andoperator’s performance. Press and at the same time and “*INFO MODE*” shows on display. Press or to access the steps and press to view the statistics withineach step. Information Mode is intended f...

Page 37 - Press to view the following information from the most; Only if Presently Cooking:; FUNCTION; Press to continue to REVIEW USAGE.

Model OFE- 291 3-17. INFORMATION MODE 2. LAST LOAD (Continued) Press to view the following information from the most recent Cook Cycle. FUNCTION DISPLAY EX: Time of day the last cook cycle was started STARTED 10.25A Product (Last product cooked) PRODUCT -2- Ready? (Was fryer Ready before start?) REA...

Page 38 - Press to view the accumulated information since the data; FILTERED 34; Percentage of Cook Cycles before oil change; Press to continue to INP A_CVHDSF_M

Model OFE- 291 3-18. INFORMATION MODE 4. REVIEW USAGE (Continued) Press to view the accumulated information since the data was manually reset: FUNCTION DISPLAY EX: Day the usage data was previously reset SINCE APR-19 Number of hours the fryer was on PWR ON HRS 165 Number of times oil was filtered FI...

Page 39 - Press to view the specific status of each input. An

Model OFE- 291 3-18. INFORMATION MODE Press to view the specific status of each input. An (Continued) underscore (“_”) indicates the input is not presently detected.A checkmark (“ ”) indicates the signal is detecting a normalinput. A blinking (“X”) indicates the signal is presentlydetected, but is d...

Page 40 - the relays on the output PC board.

Model OFE- 291 3-18. INFORMATION MODE Press and “6. PMP_ AIR_” shows in display. (Continued) Press to view the amp “DRAW” status of the pump motoroutput and air valve output. “PMP ” and “AIR ” in thedisplay means the amps are good. A flashing “X” behind the“PMP” or “AIR” means too much current. Pres...