Envision EN7410 - Manuals

Envision EN7410 – Manual in PDF format online.

Manuals:

Manual

Manual Envision EN7410

Summary

Page 2 - FOR YOUR SAFETY; FCC Class B Radio Frequency Interference Statement

i FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for...

Page 3 - ii

ii PRECAUTIONS: • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. ...

Page 4 - iii

iii circuit parts causing a fire or electric shock. Never spill liquids on the monitor. • Do not attempt to service the monitor by yourself. Opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. • Do not pull or ...

Page 5 - iv; GENERAL NOTES

iv GENERAL NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly...

Page 7 - vi; Disclaimer; Reference Information; Monitor Information

vi Disclaimer Envision Peripherals Inc. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Envision Peripherals Inc. reserves the right to ...

Page 8 - vii; Table of Contents

vii Table of Contents 1 1 Important Safety Instructions ........................................... i 2 2 Features............................................................................. 2 3 3 Unpacking the Monitor ..................................................... 3 4 Hardware Installation ...

Page 9 - Important Safety Instructions; covers may expose you to dangerous voltages or other hazards.

1 1 1 Important Safety Instructions Please read the following safety instructions before installing or cleaning your Envision monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. 2. Sl...

Page 10 - Features; Your Envision EN7410 Monitor features:

2 2 2 Features Your Envision EN7410 Monitor features: ♦ SXGA (1280 x 1024 pixel) Resolution LCD Panel ♦ High Brightness – 300 cd/m 2 (typical) ♦ High Contrast Ratio – 400:1 (typical) ♦ True Colour Display With FRC support for 16.7M colours, the Envision EN7410 monitor offers you better image quality...

Page 11 - Unpacking the Monitor; immediately

3 3 3 Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately . Monitor 1 pc 1 pc 1 pc 1 pc Signal Cable Power Cable QSG (Quick Start Guide) CD User’s Manual

Page 12 - Hardware Installation; the VGA output connector of the computer‘s graphics card.; Power cable

4 4 4 Hardware Installation Your monitor is equipped with an automatic power supply with a voltage range from 100 to 240 Volts AC at a frequency of 50 to 60 Hz. Make sure that your local power supply is within the supported range. If you are unsure, please contact your electricity supplier. To insta...

Page 13 - Windows driver Installation; drivers are required to be loaded.; Add New Hardware; Just follow the prompts to load the native Plug and Play drivers.; Windows XP; XP will automatically load the native Plug and Play drivers.

5 5 5 Windows driver Installation The Envision EN7410 is fully Windows compatible so no specific windows drivers are required to be loaded. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add ...

Page 14 - Setting the Display Resolution; Choosing The Best Resolution; Display; For Windows NT users only:; Test

6 6 6 Setting the Display Resolution Choosing The Best Resolution All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as the maximum resolution that may be displayed on the LCD. In the case of the EN7410 the LCD resolution is 1280 x 1024 pixels. This is also known as the “nat...

Page 16 - Adjusting the Monitor; Table 1

8 caused by the signal from the VGA card if it does not correspond with the usual standard. This is not however, a problem with the monitor. If it is still visible after using the Automatic adjustment, you can usually improve the displayed image by manually adjusting the phase, horizontal position a...

Page 17 - Picture Optimisation; The easiest way to obtain an optimal picture is by using the; Auto; button for 2; OSD Adjustment

9 7 7 Adjusting the Monitor Picture Optimisation The easiest way to obtain an optimal picture is by using the Auto button for 2 seconds. This only works reliably if the graphics adaptor is set to use one of the monitor’s factory modes (see Table 1 in the previous chapter) and if you are displaying a...

Page 21 - Frequently Asked Questions; The image is blurred, how can I get the best quality picture?

13 8 8 Frequently Asked Questions The image is blurred, how can I get the best quality picture? ♦ Read chapter 6, Setting the Display Resolution , and select a graphics signal with the correct resolution and refresh rate. Then read chapter 7, Adjusting the Monitor , and make adjustments to the displ...

Page 22 - MENU; NON PRESET MODE; The image is or distorted, flashes or flickers:

14 No image is displayed, what can I do? ♦ Check that the light (LED) next to the monitor’s power button is lit and is green in colour. If the LED is green, press the MENU button on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Sett...

Page 23 - The display shows OUT OF FREQUENCY error message:

15 The display shows OUT OF FREQUENCY error message: ♦ Read chapter 6, Setting the Display Resolution , and select a graphics signal with the correct resolution and refresh rate.

Page 24 - Specifications; Display Characteristics

16 9 9 Specifications Model: Envision EN7410 Display Characteristics Display Type 17“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 43.18 cm / 17” Native (Maximum) Resolution 1,280 x 1,024 pixels Colors 16.7 million (6bpp+dithering) Contrast Ratio 400:1 (typical) B...

Page 25 - Input Signal; TTL separate, composite TTL; Physical Characteristics; Energy Star; Regulatory Certification

17 Input Signal Line Frequency 31 - 83kHz multi-frequency Image Frequency (Refresh Rate) 56 - 75Hz Within the parameters detailed in chapter 7 Video Signal RGB analogue (Positive polarity) 0.7 Vpp/75 Ohm Synchronization TTL separate, composite TTL Signal Connection 15-pin mini D-sub cable Physical C...