Envision EN9410 - Manual

iv GENERAL NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly...

vi Disclaimer Envision Peripherals Inc. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Envision Peripherals Inc. reserves the right to ...

vii Table of Contents 1 1 Important Safety Instructions ........................................... i 2 2 Features............................................................................. 2 3 3 Unpacking the Monitor ..................................................... 3 Installation and Removal...

1 1 1 Important Safety Instructions Please read the following safety instructions before installing or cleaning your Envision monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. 2. Sl...

2 2 2 Features Your Envision EN9410 Monitor features: ♦ SXGA (1280 x 1024 pixel) Resolution LCD Panel ♦ High Brightness – 250 cd/m 2 (typical) ♦ High Contrast Ratio – 500:1 (typical) ♦ True Colour Display With FRC support for 16.7M colours, the Envision EN9410 monitor offers you better image quality...

3 3 3 Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately . Monitor 1 pc 1 pc 1 pc 1 pc Signal Cable Power Cable QSG (Quick Start Guide) CD User’s Manual Installation and Removal...

4 4 4 Hardware Installation Your monitor is equipped with an automatic power supply with a voltage range from 100 to 240 Volts AC at a frequency of 50 to 60 Hz. Make sure that your local power supply is within the supported range. If you are unsure, please contact your electricity supplier. To insta...

5 5 5 Windows driver Installation The Envision EN9410 is fully Windows compatible so no specific windows drivers are required to be loaded. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add ...

6 6 6 Setting the Display Resolution Choosing The Best Resolution All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as the maximum resolution that may be displayed on the LCD. In the case of the EN9410 the LCD resolution is 1280 x 1024 pixels. This is also known as the “nat...

8 caused by the signal from the VGA card if it does not correspond with the usual standard. This is not however, a problem with the monitor. If it is still visible after using the Automatic adjustment, you can usually improve the displayed image by manually adjusting the phase, horizontal position a...

9 7 7 Adjusting the Monitor Picture Optimisation The easiest way to obtain an optimal picture is by using the Auto button for 2 seconds. This only works reliably if the graphics adaptor is set to use one of the monitor’s factory modes (see Table 1 in the previous chapter) and if you are displaying a...

10 (from left to right) Menu Enter OSD menu. Enter submenus or select items within OSD menu. c Move the selection cursor upwards within the OSD menu. d Move the selection cursor downwards within the OSD menu. e Adjust OSD functions. (Decrease) f Adjust OSD functions. (Increase) SELECT /AUTO Automati...

13 8 8 Frequently Asked Questions The image is blurred, how can I get the best quality picture? ♦ Read chapter 6, Setting the Display Resolution , and select a graphics signal with the correct resolution and refresh rate. Then read chapter 7, Adjusting the Monitor , and make adjustments to the displ...

14 No image is displayed, what can I do? ♦ Check that the light (LED) next to the monitor’s power button is lit and is green in colour. If the LED is green, press the MENU button on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Sett...

15 The display shows OUT OF FREQUENCY error message: ♦ Read chapter 6, Setting the Display Resolution , and select a graphics signal with the correct resolution and refresh rate.

16 9 9 Specifications Model: Envision EN9410 Display Characteristics Display Type 19“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 43.3 cm / 19” Native (Maximum) Resolution 1,280 x 1,024 pixels Colors 16.7 million (6bpp+dithering) Contrast Ratio 500:1 (typical) Br...