Page 2 - For Your Safety; FCC Statement
EN-5200e/ei 2 29JUL02 EN-5200e/ei For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resident...
Page 3 - Precautions
EN-5200e/ei 3 29JUL02 EN-5200e/ei For Your Safety Precautions • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a pers...
Page 4 - Special Notes on LCD Monitors
EN-5200e/ei 4 29JUL02 EN-5200e/ei For Your Safety Special Notes on LCD Monitors The following symptoms are normal with an LCD monitor and do not indicate a problem: • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on ...
Page 5 - Before You Operate the Monitor; Installing & Removing the Base; Package Contents
EN-5200e/ei 5 29JUL02 EN-5200e/ei Before You Operate the Monitor Installing & Removing the Base General Features: • 38.1cm(15") TFT Color LCD Monitor • Crisp, Clear Display for Windows • Supports Resolutions up to 1024 X 768 pixels @75Hz, (1024 x 768 @ 60Hz Recommended) • EPA ENERGY STAR ® •...
Page 6 - Connecting the Wires Using the Power Cord Supplied (EN-5200e)
EN-5200e/ei 6 29JUL02 EN-5200e/ei Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied (EN-5200e) 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your LCD monitor's Powe...
Page 7 - Connecting the Wires Using the Power Cord Supplied (EN-5200ei)
EN-5200e/ei 7 29JUL02 EN-5200e/ei Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied (EN-5200ei) 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord to your monitor. 3. Plug th...
Page 8 - Adjusting the Viewing Angle
EN-5200e/ei 8 29JUL02 EN-5200e/ei Before You Operate the Monitor Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. • Hold the stand firmly when you change the monitor's angle. • You can adjust the monitor's angle from -5° to 25°. • Do not touch the L...
Page 9 - Preparing To Install An Optional Wall Mounting Arm (Not Supplied)
EN-5200e/ei 9 29JUL02 EN-5200e/ei Before You Operate the Monitor Preparing To Install An Optional Wall Mounting Arm (Not Supplied) This monitor can be attached to a wall mounting arm you can purchase separately. Disconnect power before performing this procedure. Follow these step. 1. Pull the screw ...
Page 10 - nstall An Optional Wall Mounting Arm (Not Supplied)
EN-5200e/ei 10 29JUL02 EN-5200e/ei Before You Operate the Monitor nstall An Optional Wall Mounting Arm (Not Supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of...
Page 11 - Operating Instructions; Front Panel Buttons
EN-5200e/ei 11 EN-5200e/ei 29JUL02 Operating Instructions Front Panel Buttons Auto : Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Brightness : Press this button to adjust the picture’s brightness. If the OSD window is open, this button allows you to mo...
Page 12 - Adjusting the OSD Settings
EN-5200e/ei 12 29JUL02 EN-5200e/ei Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change ...
Page 13 - How to Install INF & ICM File
EN-5200e/ei 13 29JUL02 EN-5200e/ei Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate a...
Page 15 - Problem; Error Message
EN-5200e/ei 15 29JUL02 EN-5200e/ei Technical Support (FAQ) 1 CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture’s width is incorrect. 2 FOCUS adjusts the phase of the pixel clock si...
Page 16 - Resolution Chart
EN-5200e/ei 16 29JUL02 EN-5200e/ei Technical Support (FAQ) Resolution Chart Error Message Possible Solution Input not supported • Your computer has been set to an incompatible display mode. Right click on the desktop and choose Properties. Click the Settings tab then set your computer’s display mode...
Page 17 - Appendix; Specifications
EN-5200e/ei 17 29JUL02 EN-5200e/ei Appendix Specifications LCD Panel Driving system TFT Color LCD Size 15.0" (38.1 cm) Pixel pitch (0.297 mm) (H) x (0.297 mm) (V) Viewable angle 120° (H) 100° (V) Input Response time 30 milliseconds Video Red, Green, BlueAnalog Interface Separate Sync. H/V TTL H-...
Page 19 - Factory Preset Timing Table
EN-5200e/ei 19 29JUL02 EN-5200e/ei Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency VGA 720 × 400 31.47 kHz 70 Hz 640 × 480 31.47 kHz 60 Hz 640 × 480 35.00 kHz 66.6 Hz 640 × 480 37.50 kHz 75 Hz SVGA 800 × 600 37.879 kHz 60 Hz 800 × 600 46.8...
Page 20 - Connector Pin Assignment; Pin Number
EN-5200e/ei 20 29JUL02 EN-5200e/ei Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 +5V 2 Green 10 Detect Cable 3 Blue 11 NC 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground
