Page 2 - NOTICE
EN9110 1 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class ...
Page 3 - PRECAUTIONS
EN9110 2 ! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. ! Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use onl...
Page 4 - packed at the factory.
EN9110 3 • For maximum protection, repackage your monitor as it was originally packed at the factory. • To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents suc...
Page 5 - NOTES; BEFORE YOU OPERATE THE MONITOR; The product package should include the following items:; FEATURES
EN9110 4 The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly u...
Page 6 - Install; POWERCORD
EN9110 5 INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in eithe...
Page 7 - PREPARING TO INSTALL THE CABLES
EN9110 6 PREPARING TO INSTALL THE CABLES 1. Remove the wall mounting hole cover. 2. Remove the cable cover. INSTALLATIONS INSTRUCTIONS (cont)
Page 8 - CABLE; CONNECTIONS; Figure 2 Connecting Cables
EN9110 7 CABLE CONNECTIONS 1 – Connect the DC-jack power cable into DC-IN connector on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 3. (Optional – Requires a video card with DVI port) Connect ...
Page 10 - Attaching The Optional Wall Mount Arm (not supplied); Follow these steps to finish installing the wall mounting arm:
EN9110 9 Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Insert the 4 screws into the holes and ...
Page 12 - OPERATING INSTRUCTIONS; The power cord should be connected.; EXTERNAL CONTROLS; Button; GENERAL INSTRUCTIONS
EN9110 11 OPERATING INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connec...
Page 13 - FRONT PANEL CONTROL; Power Button; W hen OSD menu is in active status, this button will act as EXIT-KEY
EN9110 12 FRONT PANEL CONTROL • Power Button : Press this button to switch the monitor’s power ON or OFF. • MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/Contrast OSD status. • Brightness / : Adjust bri...
Page 14 - HOW TO ADJUST A SETTING
EN9110 13 1. Press the MENU-button to activate the OSD window. See figure 5. 2. Press or to select the desired function. See figure 5. 3. Press the MENU-button again to activate the highlighted function. 4. Press or to adjust the selected function. Note: is used to adjust the function down & is ...
Page 15 - ADJUSTING THE PICTURE
EN9110 14 Below describes the function of each OSD icon. 1. Contrast Adjust the picture contrast. 2. Brightness Adjust the picture brightness. 3. Input Selected Input Signal source selected ( select Analog or Digital input source ) 4. Focus Adjust picture Focus (available in Analog mode only). 5. Cl...
Page 16 - USING THE RIGHT POWER CORD :; female configuration.; PLUG AND PLAY
EN9110 15 Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabili...
Page 18 - color temperature from OSD.
EN9110 17 Screen image is not centered or sized properly. *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO) Picture has color defects (white does not look white) *Adjust RGB color or select a pre-set color temperature from OSD. Horizontal or vertical disturbances on the screen *Use w...
Page 19 - RESOLUTION; ERROR MESSAGE & POSSIBLE SOLUTION
EN9110 18 NO SIGNAL 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT Your computer has been set to unsuitable display mode ,set the computer to display mode give...
Page 22 - APPENDIX; SPECIFICATIONS
EN9110 21 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 48cm(19.0") Pixel pitch 0.294mm( H )x 0.294mm( V ) Viewable angle 170 ° (H) 170 ° (V) Response time 25 ms ( Typical ) Video R,G,B Analog Interface Input Separate Sync. H/V TTL H-Frequency 31KHz – 92KHz V-Frequency 55-8...
Page 24 - FACTORY PRESET TIMING TABLE
EN9110 23 STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 640 × 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0Hz VGA 640 × 480 31.47kHz 60.0Hz 640 × 480 35.00kHz 66.6Hz 640 × 480 37.50kHz 75.0Hz 640 × 480 37.86kHz 72.0Hz 800 × 600 37.879k...
Page 25 - CONNECTOR PIN ASSIGNMENT
EN9110 24 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. NC 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 24 - Pin Color Display S...
Page 27 - WARRANTY STATEMENT; for Envision Color Monitors
EN9110 26 WARRANTY STATEMENT for Envision Color Monitors Including those Sold within North America as Specified Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of three (3) years after the original date of consumer purchase. During th...
