Page 2 - For Your Safety; FCC Statement
EN7400e 2 12OCT04 EN7400e For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential inst...
Page 3 - Precautions
EN7400e 3 12OCT04 EN7400e Precautions • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious dam...
Page 4 - Special Notes on LCD Monitors
EN7400e 4 12OCT04 EN7400e For Your Safety Special Notes on LCD Monitors The following symptoms are normal with an LCD monitor and do not indicate a problem: • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to...
Page 5 - Before You Operate the Monitor; Installing & Removing the Base; Package Contents
EN7400e 5 12OCT04 EN7400e Before You Operate the Monitor Installing & Removing the Base General Features: • 17" (43.2cm) TFT Color LCD Monitor • Crisp, Clear Display for Windows • Supports Resolutions up to 1280 X 1024 pixels @75Hz, (1280 x 1024 @ 60Hz Recommended) • EPA ENERGY STAR ® • Ergo...
Page 6 - Connecting the Wires Using the Power Cord Supplied
EN7400e 6 12OCT04 EN7400e Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into the power adaptor. 3. Connect the power ad...
Page 7 - Preparing to Install An Optional Wall Mounting Arm (Not supplied)
EN7400e 7 12OCT04 EN7400e Before You Operate the Monitor Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Pull the screw covers off the back of...
Page 8 - Install An Optional Wall Mounting Arm (Not supplied)
EN7400e 8 12OCT04 EN7400e Before You Operate the Monitor Install An Optional Wall Mounting Arm (Not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the mon...
Page 9 - Adjusting the Viewing Angle
EN7400e 9 12OCT04 EN7400e Before You Operate the Monitor Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. • Hold the stand firmly when you change the monitor's angle. • You can adjust the monitor's angle from -5° to 25°. • Do not touch the LCD scree...
Page 10 - Operating Instructions; Front Panel Buttons
EN7400e 10 12OCT04 EN7400e Operating Instructions Front Panel Buttons Auto : Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Power Indicator : A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. Brigh...
Page 11 - Adjusting the OSD Settings
EN7400e 11 12OCT04 EN7400e Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the sett...
Page 14 - Problem; Error Message
EN7400e 14 12OCT04 EN7400e Technical Support (FAQ) 1 CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture’s width is incorrect. 2 FOCUS adjusts the phase of the pixel clock signal. Wi...
Page 15 - Resolution Chart
EN7400e 15 12OCT04 EN7400e Technical Support (FAQ) Resolution Chart Error Message Possible Solution Input not supported • Your computer has been set to an incompatible display mode. Right click on the desktop and choose Properties. Click the Settings tab then set your computer’s display mode to one ...
Page 16 - Appendix; Specifications
EN7400e 16 12OCT04 EN7400e Appendix Specifications LCD Panel Driving system TFT Color LCD Size 17" (43.2 cm) Diagonal Pixel pitch 0.264 mm (H) x 0.264 mm (V) Viewable angle 140° (H) 125° (V) Input Response time 16 milliseconds Video Red, Green, BlueAnalog Interface Separate Sync. H/V TTL H-Frequ...
Page 18 - Factory Preset Timing Table
EN7400e 18 12OCT04 EN7400e Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency DOS-Mode 600 x 400 31.47 kHz 70 Hz 720 x 400 31.47 kHz 70 Hz VGA 640 x 480 31.47 kHz 60 Hz 640 × 480 35.00 kHz 66.6 Hz 640 × 480 37.50 kHz 75 Hz SVGA 800 × 600 37.8...
Page 19 - Connector Pin Assignment; Pin Number
EN7400e 19 12OCT04 EN7400e Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 +5V 2 Green 10 Detect Cable 3 Blue 11 NC 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground