Envision EN7220 - Manuals

Envision EN7220 – Manual in PDF format online.

Manuals:

Manual

Manual Envision EN7220

Summary

Page 2 - TABLE OF CONTENTS

EN7220 1 TABLE OF CONTENTS Table of Contents 1 For Your Safety 2 Precautions 3 General Notes 4-5 Before You Operate The Monitor 6 Installation Instructions 7-1 3 Operating Instructions 1 4 -1 9 Technical Support (FAQ) 20 -2 1 Appendix 2 2 -2 5

Page 3 - FOR YOUR SAFETY

EN7220 2 FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the lim...

Page 4 - PRECAUTIONS

EN7220 3 z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use onl...

Page 6 - This monitor is equipped with VESA

EN7220 5 GENERAL NOTES (cont) •••• Plug & Play DDC1/2B Feature - This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information...

Page 7 - BEFORE YOU OPERATE THE MONITOR; Crisp & Clear Display for W indows; CHECKING THE CONTENTS OF THE PACKAGE

EN7220 6 BEFORE YOU OPERATE THE MONITOR • 17” (43.2cm) TFT Color LCD Monitor • Crisp & Clear Display for W indows • Recommended Resolutions: 1280 X 1024 @ 60Hz • EPA E NERGY S TAR ® • Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand • Height, Pivot, Tilt & Swivel Adjus...

Page 8 - INSTALLATION INSTRUCTIONS; INSTALLING & REMOVING THE BASE; Install; INSTALLING THE BASE; Remove Pin; REMOVING THE BASE

7 INSTALLATION INSTRUCTIONS INSTALLING & REMOVING THE BASE Install Figure 1 - Installing the Base. INSTALLING THE BASE 1. Set the bottom base on a flat surface. 2. Line up the front of the monitor with the front of the base and press firmly. Remove Pin Remove Base Figure 2 - Installing the Base....

Page 9 - female configuration.

8 INSTALLATION INSTRUCTIONS (Cont) POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) ...

Page 10 - Connecting The Cables; Figure 2 Connecting Cables

EN7220 9 INSTALLATION INSTRUCTIONS (Cont) Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AW G, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, ...

Page 11 - How To Install The INF & ICM Files; ENVISIONdisplay

EN7220 10 INSTALLATION INSTRUCTIONS (cont) How To Install The INF & ICM Files •••• This is a Plug & Play monitor. Microsoft W indows will automatically install a Plug & Play driver for it when you first install this monitor. It is not necessary to install the INF driver file included in ...

Page 12 - NOTES; cause damage or break the LCD screen.

EN7220 1 1 INSTALLATION INSTRUCTIONS (cont) Height, Tilt, Pivot & Swivel Adjustment Your monitor features a multi-adjustable stand that will enable it move 110mm up/down (height adjustment), 25 degree forward/backward (tilt adjustment), 90 degree landscape/portrait (pivot adjustment) and 7 0 deg...

Page 13 - Remove the 2 screws that hold the plastic hinge cover.

EN7220 1 2 INSTALLATION INSTRUCTIONS (cont) Preparing To Install The Optional Wall Mount Arm (Not Included) This monitor can be attached to a wall mounting arm you can purchase separately. Turn the power OFF then dis-connect the cables from the monitor before performing the procedure below. Lay the ...

Page 14 - Attaching The Optional Wall Mount Arm (not supplied); Follow these steps to finish installing the wall mounting arm:

EN7220 1 3 INSTALLATION INSTRUCTIONS (cont) Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Inse...

Page 15 - Figure 4 - External Controls; EXTERNAL CONTROLS; Press this button to turn the monitor ON or OFF.

EN7220 1 4 EXTERNAL CONTROLS Figure 4 - External Controls EXTERNAL CONTROLS 1. Power Button 4. > or Contrast Button 2. LED 5. < or Brightness Button 3. MENU / ENTER Button 6. Auto Adjust / Exit Button • Power Button: Press this button to turn the monitor ON or OFF. • MENU / ENTER: This button ...

Page 19 - 亞᫿խ֮

EN7220 1 8 OPERATING INSTRUCTIONS (cont) Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Yes N/A Auto Adjust the H/V Position, Focus and Clock of picture. N/A Auto Config No N/A Do not execute Auto Config, return to main menu. N/A H. Position Adjust the horizontal p...

Page 22 - to a display mode given in the Preset Display Modes table.; ERROR MESSAGE & POSSIBLE SOLUTION

EN7220 2 1 TECHNICAL SUPPORT (FAQ) (cont) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. W ith a wrong ...

Page 23 - APPENDIX; SPECIFICATIONS

EN7220 2 2 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 43.2cm(17.0") Pixel pitch 0.264mm( H )x 0.264mm( V ) Viewable angle 140 ° (H) 130 ° (V) Response time 16 ms Video R,G,B Analog Interface H-Frequency 30KHz – 83KHz V-Frequency 55-75Hz Display Colors 16.2M Colors Dot Cl...

Page 26 - Connector Pin Assignment

EN7220 2 5 APPENDIX (cont) Connector Pin Assignment 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. ...