Envision EN-980E - Manuals - manualsarea.com

Page 2 - For Your Safety; FCC Statement

EN-980e 2 31MY02 EN-980e For Your Safety FCC Statement This equipment has been tested and found tocomply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protectionagainst harmful interference in a residentialinstallati...

Page 3 - Precautions

EN-980e 3 31MY02 EN-980e For Your Safety Precautions • Do not use the monitor near water, e.g. near abathtub, washbowl, kitchen sink, laundry tub,swimming pool or in a wet basement. • Do not place the monitor on an unstable cart,stand, or table. If the monitor falls, it can injure aperson and cause ...

Page 4 - General Notes; Package Contents

EN-980e 4 31MY02 EN-980e For Your Safety General Notes • Do not install the monitor near heat sourcessuch as radiators or air ducts. • Do not place monitor in direct sunlight or inareas with excessive dust, mechanical vibrationor shock. • Save the original shipping carton and packingmaterials in cas...

Page 5 - Before You Operate the Monitor; Installing & Removing the Base

EN-980e 5 31MY02 EN-980e Before You Operate the Monitor Installing & Removing the Base

Page 6 - Connecting the Wires Using the Power Cord Supplied

EN-980e 6 31MY02 EN-980e Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer andtighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug t...

Page 7 - Connecting the Wires Using An Optional Power Cord (Not Supplied)

EN-980e 7 31MY02 EN-980e Before You Operate the Monitor Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor canonly be connected to a grounded electrical wallsocket or power strip. If you wish to connect your monitor to a powersupply using the p...

Page 8 - Operating Instructions; Front Panel Buttons

EN-980e 8 EN-980e 31MY02 Operating Instructions Front Panel Buttons Exit: Press this button to save changes andclose the OSD window. Brightness: Press this button to adjust thepicture’s brightness. If the OSD window isopen, this button allows you to move withinthe window and select desired functions...

Page 9 - Adjusting the OSD Settings

EN-980e 9 31MY02 EN-980e Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the settin...

Page 10 - Windows INF Driver File

EN-980e 10 31MY02 EN-980e Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2Bcapabilities according to the VESA DDCSTANDARD. It allows the monitor to inform thehost system of its identity and, depending on thelevel of DDC used, communicate additionalinfo...

Page 12 - Appendix; Specifications

EN-980e 12 31MY02 EN-980e Appendix Specifications CRT Size 19.0" (48.3 cm) 11.4” (29 mm) neck 0.25mm(D),0.21mm(H) dot pitch 90 degree deflection Viewable image size 18.0” (45.3 cm)diagonal Preset Display area 13.7” (346 mm) X10.3” (260 mm) Dot Clock 200 MHz Maximum Resolution 1600 x 1200 pixels ...

Page 14 - Factory Preset Timing Table

EN-980e 14 31MY02 EN-980e Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency VGA 720 × 400 31.5 kHz 70 Hz 640 × 480 31.5 kHz 60 Hz VESA / 85 640 × 480 43.3 kHz 85 Hz 800 × 600 53.7 kHz 85 Hz 1024 × 768 68.7 kHz 85 Hz 1280 × 960 85.9 kHz 85 Hz...

Page 15 - Connector Pin Assignment

EN-980e 15 31MY02 EN-980e Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground