Envision EN-775E - Manuals - manualsarea.com

Page 2 - For Your Safety; FCC Statement

EN-775e 2 31MY02 EN-775e For Your Safety FCC Statement This equipment has been tested and found tocomply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protectionagainst harmful interference in a residentialinstallati...

Page 3 - Precautions

EN-775e 3 31MY02 EN-775e For Your Safety Precautions • Do not use the monitor near water, e.g. near abathtub, washbowl, kitchen sink, laundry tub,swimming pool or in a wet basement. • Do not place the monitor on an unstable cart,stand, or table. If the monitor falls, it can injure aperson and cause ...

Page 4 - General Notes; Package Contents

EN-775e 4 31MY02 EN-775e For Your Safety General Notes • Do not install the monitor near heat sourcessuch as radiators or air ducts. • Do not place monitor in direct sunlight or inareas with excessive dust, mechanical vibrationor shock. • Save the original shipping carton and packingmaterials in cas...

Page 5 - Before You Operate the Monitor; Installing & Removing the Base

EN-775e 5 31MY02 EN-775e Before You Operate the Monitor Installing & Removing the Base

Page 6 - Connecting the Wires Using the Power Cord Supplied

EN-775e 6 31MY02 EN-775e Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer andtighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug t...

Page 7 - Connecting the Wires Using An Optional Power Cord (Not Supplied)

EN-775e 7 31MY02 EN-775e Before You Operate the Monitor Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor canonly be connected to a grounded electrical wallsocket or power strip. If you wish to connect your monitor to a powersupply using the p...

Page 8 - Operating Instructions; Front Panel Buttons

EN-775e 8 EN-775e 31MY02 Operating Instructions Front Panel Buttons Exit: Press this button to savechanges and close the OSD window. Brightness: Press this button to adjust thepicture’s brightness. If the OSD window isopen, this button allows you to move withinthe window and select desired functions...

Page 9 - Adjusting the OSD Settings

EN-775e 9 31MY02 EN-775e Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the settin...

Page 10 - Windows INF Driver File

EN-775e 10 31MY02 EN-775e Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2Bcapabilities according to the VESA DDCSTANDARD. It allows the monitor to inform thehost system of its identity and, depending on thelevel of DDC used, communicate additionalinfo...

Page 12 - Appendix; Specifications

EN-775e 12 31MY02 EN-775e Appendix Specifications CRT Size 17.0" (43.2 cm) 11.4” (29 mm) neck 0.21mm(H),0.25mm(D) dotpitch 90 degree deflec-tion Viewable image size 16.0” (40.6 cm)diagonal Preset Display area 11.8” (300 mm) X9.1” (230 mm) Dot Clock 110 MHz Maximum Resolution 1280 x 1024 pixels P...

Page 14 - Factory Preset Timing Table

EN-775e 14 31MY02 EN-775e Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency VGA 720 × 400 31.5KHz 70 Hz 640 × 480 31.5KHz 60 Hz VESA / 85 640 x 480 43.3KHz 85Hz 800 x 600 53.7KHz 85Hz 1024 x 768 68.7KHz 85Hz VESA / 60 1280 × 1024 64.0 kHz 60...

Page 15 - Connector Pin Assignment

EN-775e 15 31MY02 EN-775e Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground