Envision EN-7100e - Manuals

Envision EN-7100e – Manual in PDF format online.

Manuals:

Manual

Manual Envision EN-7100e

Summary

Page 2 - For Your Safety; FCC Statement

EN-7100e 2 31MY02 EN-7100e For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins...

Page 3 - Precautions

EN-7100e 3 31MY02 EN-7100e Precautions • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious da...

Page 4 - Special Notes on LCD Monitors

EN-7100e 4 31MY02 EN-7100e For Your Safety Special Notes on LCD Monitors The following symptoms are normal with an LCD monitor and do not indicate a problem: • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again t...

Page 5 - Before You Operate the Monitor; Installing & Removing the Base; Package Contents

EN-7100e 5 31MY02 EN-7100e Before You Operate the Monitor Installing & Removing the Base General Features: • 17" (43.2cm) TFT Color LCD Monitor • Crisp, Clear Display for Windows • 1280 X 1024 pixels @75Hz Maximum & Recommended Resolution • EPA ENERGY STAR ® • Ergonomic Design • Space Sa...

Page 6 - Connecting the Wires Using the Power Cord Supplied

EN-7100e 6 31MY02 EN-7100e Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into the power adaptor. 3. Plug the other end ...

Page 7 - Connecting the Wires Using An Optional Power Cord (Not Supplied)

EN-7100e 7 31MY02 EN-7100e Before You Operate the Monitor Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using ...

Page 8 - Preparing to Install An Optional Wall Mounting Arm (Not supplied)

EN-7100e 8 31MY02 EN-7100e Before You Operate the Monitor Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Pull the screw covers off the back o...

Page 9 - Install An Optional Wall Mounting Arm (Not supplied)

EN-7100e 9 31MY02 EN-7100e Before You Operate the Monitor Install An Optional Wall Mounting Arm (Not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the mo...

Page 10 - Adjusting the Viewing Angle

EN-7100e 10 31MY02 EN-7100e Before You Operate the Monitor Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. • Hold the stand firmly when you change the monitor's angle. • You can adjust the monitor's angle from -5° to 30°. • Do not touch the LCD scr...

Page 11 - Operating Instructions; Front Panel Buttons

EN-7100e 11 EN-7100e 31MY02 Operating Instructions Front Panel Buttons Auto: Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Brightness: Press this button to adjust the picture’s brightness. If the OSD window is open, this button allows you to move within...

Page 12 - Adjusting the OSD Settings

EN-7100e 12 31MY02 EN-7100e Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the set...

Page 13 - How to Optimize the DOS-mode

EN-7100e 13 31MY02 EN-7100e Operating Instructions DOS-mode This feature allows you to choose between resolutions of 720 x 400 or 640 x 400 while working in DOS-mode. Follow the instructions for selecting functions in the OSD window as listed on the previous page. Press your monitor’s Power button o...

Page 15 - Problem

EN-7100e 15 31MY02 EN-7100e Technical Support (FAQ) 1 CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture’s width is incorrect. 2 FOCUS adjusts the phase of the pixel clock signal. W...

Page 16 - Resolution Chart

EN-7100e 16 31MY02 EN-7100e Technical Support (FAQ) Resolution Chart Error Message Possible Solution Input not supported • Your computer has been set to an incompatible display mode. Right click on the desktop and choose Properties. Click the Settings tab then set your computer ’s display mode to on...

Page 17 - Appendix; Specifications

EN-7100e 17 31MY02 EN-7100e Appendix Specifications LCD Panel Driving system TFT Color LCD Size 17.0" (43.2 cm) Diagonal Pixel pitch 0.264 mm (H) x 0.264 mm (V) Viewable angle 120° (H) 100° (V) Input Response time 50 milliseconds Video Red, Green, BlueAnalog Interface Separate Sync. H/V TTL H-Fr...

Page 19 - Factory Preset Timing Table

EN-7100e 19 31MY02 EN-7100e Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency DOS-Mode 600 x 400 31.47 kHz 70 Hz 720 x 400 31.47 kHz 70 Hz VGA 640 x 480 31.47 kHz 60 Hz 640 × 480 35.00 kHz 66.6 Hz 640 × 480 37.50 kHz 75 Hz SVGA 800 × 600 37....

Page 20 - Connector Pin Assignment; Pin Number

EN-7100e 20 31MY02 EN-7100e Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 +5V 2 Green 10 Detect Cable 3 Blue 11 NC 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground

Page 21 - Limited 3-Year Warranty

EN-7100e 21 31MY02 EN-7100e Limited 3-Year Warranty This is a warranty statement for Envision color monitors including those sold within North America as specified. Envision Peripherals, Inc. (EPI) warrants this product to be free from defects in material and workmanship for a period of three (3) ye...