Envision EN-5100E - Manuals

Envision EN-5100E – Manual in PDF format online.

Manuals:

Manual

Manual Envision EN-5100E

Summary

Page 2 - For Your Safety; FCC Statement

EN-5100e 2 31MY02 EN-5100e For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins...

Page 3 - Precautions

EN-5100e 3 31MY02 EN-5100e For Your Safety Precautions • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and ...

Page 4 - Special Notes on LCD Monitors

EN-5100e 4 31MY02 EN-5100e For Your Safety Special Notes on LCD Monitors The following symptoms are normal with an LCD monitor and do not indicate a problem: • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again t...

Page 5 - Before You Operate the Monitor; Installing & Removing the Base; Package Contents

EN-5100e 5 31MY02 EN-5100e Before You Operate the Monitor Installing & Removing the Base General Features: • 38.1cm(15") TFT Color LCD Monitor • Crisp, Clear Display for Windows • 1024 X 768 @ 75Hz (Maximum & Recommended Resolution) • EPA ENERGY STAR ® • Ergonomic Design • Space Saving, ...

Page 6 - Connecting the Wires Using the Power Cord Supplied

EN-5100e 6 31MY02 EN-5100e Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your LCD monitor's power input socket. 3....

Page 7 - Connecting the Wires Using An Optional Power Cord (Not Supplied)

EN-5100e 7 31MY02 EN-5100e Before You Operate the Monitor Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using ...

Page 8 - Adjusting the Viewing Angle

EN-5100e 8 31MY02 EN-5100e Before You Operate the Monitor Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. • Hold the stand firmly when you change the monitor's angle. • You can adjust the monitor's angle from -5° to 45°. • Do not touch the LCD scre...

Page 9 - Operating Instructions; Front Panel Buttons

EN-5100e 9 EN-5100e 31MY02 Operating Instructions Front Panel Buttons Auto: Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Brightness: Press this button to adjust the picture’s brightness. If the OSD window is open, this button allows you to move within ...

Page 10 - Adjusting the OSD Settings

EN-5100e 10 31MY02 EN-5100e Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the set...

Page 11 - How to Install INF & ICM File

EN-5100e 11 31MY02 EN-5100e Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate addition...

Page 13 - Problem

EN-5100e 13 31MY02 EN-5100e Technical Support (FAQ) 1 CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture’s width is incorrect. 2 FOCUS adjusts the phase of the pixel clock signal. W...

Page 14 - Resolution Chart

EN-5100e 14 31MY02 EN-5100e Technical Support (FAQ) Resolution Chart Error Message Possible Solution Input not supported • Your computer has been set to an incompatible display mode. Right click on the desktop and choose Properties. Click the Settings tab then set your computer ’s display mode to on...

Page 15 - Appendix; Specifications

EN-5100e 15 31MY02 EN-5100e Appendix Specifications LCD Panel Driving system TFT Color LCD Size 15.0" (38.1 cm) Pixel pitch 0.01” (0.3 mm) (H) x 0.01” (0.3 mm) (V) Viewable angle 100° (H) 80° (V) Input Response time 40 milliseconds Video Red, Green, BlueAnalog Interface Separate Sync. H/V TTL H-...

Page 17 - Factory Preset Timing Table

EN-5100e 17 31MY02 EN-5100e Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency VGA 720 × 400 31.47 kHz 70 Hz 640 × 480 31.47 kHz 60 Hz 640 × 480 35.00 kHz 66.6 Hz 640 × 480 37.50 kHz 75 Hz SVGA 800 × 600 37.879 kHz 60 Hz 800 × 600 46.875 kHz ...

Page 18 - Connector Pin Assignment; Pin Number

EN-5100e 18 31MY02 EN-5100e Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 +5V 2 Green 10 Detect Cable 3 Blue 11 NC 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground