DeLonghi DEGH90WF - Manuals

Page 2 - PRODUCT LABEL

2 Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. Theywill also provide a means by which to make full use ofthe features offered by your appliance. Please kee...

Page 3 - IMPORTANT PRECAUTIONS AND RECOMMENDATIONS; After use, ensure that the knobs are in off position.

3 IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FORUSE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamentalrules. In particular: ■ Never touch the appliance with wet hands or feet; ■ do not operate the appliance barefooted; ■ do not allow child...

Page 4 - Figure 1; Width; INSTALLATION; appliance

4 480 70 60 60 min 0 – 2 840 200 min 0 – 2 860 100 200 500 Area forelectrical connection Area forgas connection Figure 1 DIMENSIONS: (Note: Also refer to Figure 1 above) General Dimensions Width 860 mm Depth 500 mm Depth Below Mounting Surface 30 mm Cut-out Dimensions Width 840 mm Depth 480 mm INSTA...

Page 5 - Figure 2; This appliance shall; not; be used as a space heater, especially if installed in marine

5 750 mm 60 mm min 200 mm min 500 mm 450 mm Figure 2 CLEARANCES: Installation clearances and protection of combustible surfaces shall comply with thecurrent local regulations e.g. AG 601 (AS 5601) - Gas Installations code. Important note: This appliance shall not be used as a space heater, especiall...

Page 6 - Figure 3

6 The installation shall comply with the dimensions in Figures 1 and 2, bearing in mindthat: ■ A minimum clearance of 20 mm has to be kept between the bottom of the cooking hob and the top of an appliance or a shelf. To ensure this clearancemount the spacers, supplied with the appliance, as shown in...

Page 7 - ing care to overlap the gasket at the corners.; Figure 4; Take care not to damage the countertop.

7 INSTALLATION (Refer to Figure 4) : 1. Spread out the gasket “C” over the workbench at the edge of the cut out tak- ing care to overlap the gasket at the corners. 2. Slot in the cooking hob into the cut out of the workbench and locate it cor- rectly. 3. Adjust the clamps “A” and tighten the screws ...

Page 8 - Figure 5b; Gas connection for

8 GAS SUPPLY: ■ The connection must be executed by an authorised person according to the relevant standards. ■ Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the gasket has been placed (figures 5a-5b).Conical adaptor and gasket ar...

Page 10 - TABLE FOR THE CHOICE OF THE INJECTORS; Natural gas; INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY; with internal diameter of 10 mm minimum.; : After connection the installer must check that the; IMPORTANT WARNING; : The installer shall ensure the hose assembly is

10 TABLE FOR THE CHOICE OF THE INJECTORS Natural gas Universal LPG Test Point Pressure [kPa] 1.0 2.75 BURNER Auxiliary (A) 0.85 3.60 0.53 3.60 Medium-speed burner (SR) 1.12 6.30 0.70 6.30 Triple-ring burner (TR) 1.65 13.00 0.95 11.90 Fish burner (PS) 1.45 10.30 0.91 10.80 Gas Consumption [MJ/h] Inje...

Page 11 - CONVERSION PROCEDURE; REPLACING THE INJECTORS; To replace the injectors proceed as follows:; IMPORTANT; Figure 6

11 CONVERSION PROCEDURE (to convert to Natural gas or to ULPG) REPLACING THE INJECTORS The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or Universal LPG (check the “gastype” sticker attached to the appliance). The nominal ...

Page 12 - MINIMUM BURNER SETTING ADJUSTMENT; Normally for Universal LPG, fully tighten the adjustment screw.; LUBRICATING THE GAS TAP; Figure 8

12 MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit with thegas tap set to the minimum position. If some ports do not light, increase the minimumgas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly ...

Page 13 - ELECTRICAL REQUIREMENTS; suitable for the power consumed by the appliance.

13 INSTALLATION ELECTRICAL REQUIREMENTS ■ The appliance must be connected to the mains checking that the voltage corresponds to the value given in the rating plate and that the electricalcable sections can withstand the load specified on the plate. ■ The plug must be connected to an earthed socket i...

Page 15 - USE and CARE

15 USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is to be con-sidered as inappropriate and therefore dangerous. Do not use this appliance asa space heater. ■ Do NOT place ...

Page 16 - CONTROL PANEL; GAS BURNERS; Fish; The electric ignition is; GAS HOB

16 Figure 11 CONTROL PANEL 10. Auxiliary burner control knob (1)11. Triple-ring burner control knob (2)12. Fish burner control knob (3) 13. Left semi-rapid burner control knob (4)14. Right semi-rapid burner control knob (5) GAS BURNERS Natural Gas Universal LPG MJ/h MJ/h 1. Auxiliary burner (A) 3.6 ...

Page 17 - USING GAS BURNERS

17 USING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition . ■ Make sure that all controls are turned to zero. ■ The gas flow to the burner is controlled by the knobs on the safety taps. ■ You control the flow by turning the knob indicator to line up with the followings...

Page 18 - – Adjust the gas valve to the desired position.; Important; To re-light the burner, return the knob to the closed; wait for at; and then repeat the lighting procedure.

18 LIGHTING THE BURNERS(fitted with safety cut-off valve) In order to light the burner, you must: 1 – Turn the knob fig. 12 in anti-clockwise direction up to the maximum aperture (symbol ), push in and hold the knob; this will light the gas. 2 – Wait for about ten seconds after the gas burner has be...

Page 19 - do not use pans with concave or convex bases

19 COOKING HINTS FOR GAS HOBS ■ The burner must be chosen according to the diameter of the pans and energy required. ■ For optimum efficiency use a wok or pan no smaller than 230mm diameter. Burners Pan diameter * Auxiliary 12 - 14 cm Semi-rapid 16 - 24 cm Triple ring 26 - 28 cm Fish burner from 12x...

Page 20 - CORRECT USE OF TRIPLE-RING BURNER; To use the WOK, you must place the wok stand in the; CORRECT; position as; WRONG; GRILL FOR SMALL COOKWARE; used to prevent the cookware from tipping over.

CORRECT USE OF TRIPLE-RING BURNER ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK, you must place the wok stand in the CORRECT position as shown in fig. 15. WRONG CORRECT Figure 15 GRILL FOR SMALL COOKWARE (fig. 14) ■ Put it on the auxiliary burner (the smal...

Page 21 - Note; BURNERS AND GRIDS; Cleaning and Maintenance

21 GENERAL TIPS ■ Before cleaning the hob switch it off and wait for it to cool down. ■ Clean with a cloth, hot water and soap or liquid detergent. ■ Do not use products which are abrasive, corrosive or chlorine based. ■ Do not use steel pads. ■ Do not leave acid or alkaline substances (vinegar, sal...

Page 22 - Note: To avoid damage to the electric ignition do not use it when the

GAS TAPS ■ Regular lubrication of the gas taps must only be performed by Authorized person. ■ If the gas taps are not working properly, call our Customer Service Centre to obtain the nearest Authorized Delonghi Service Agent. CORRECT POSITIONING OF THE BURNERS ■ It is very important to check that sp...

Page 23 - CORRECT POSITIONING OF THE TRIPLE-RING BURNER; Then position the cap “

CORRECT POSITIONING OF THE TRIPLE-RING BURNER ■ The triple ring burner must be correctly positioned (see fig. 20); the burner rib must be located in position as shown by the arrow (see fig. 18). ■ The burner correctly positioned must not rotate (fig. 19). ■ Then position the cap “ A ” and the ring “...

Page 24 - CORRECT POSITIONING OF THE FISH BURNER; This burner must be correctly positioned as shown in the figure 21.

24 CORRECT POSITIONING OF THE FISH BURNER ■ This burner must be correctly positioned as shown in the figure 21. ■ Check that the electrode “ S ” (fig. 21) is always clean to ensure trouble-free sparking. ■ C heck that the probe “ T ” (fig. 21) next to the burners is always clean to ensure correct op...

Page 25 - SERVICE AND MAINTENANCE; Servicing the appliance:; LUBRICATION OF THE GAS TAPS

25 SERVICE AND MAINTENANCE If the ignition spark fails to ignite or does not light the gas, check the followingitems before calling our Customer Service Centre to obtain the nearest AuthorisedDelonghi Service Agent: ■ Burner is reassembled and located correctly. ■ Spark electrode and white ceramic a...