Page 2 - PRODUCT LABEL
2 Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. Theywill also provide a means by which to make full use ofthe features offered by your appliance. Please kee...
Page 3 - IMPORTANT PRECAUTIONS AND RECOMMENDATIONS; After use, ensure that the knobs are in off position.
3 IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FORUSE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamentalrules. In particular: ■ Never touch the appliance with wet hands or feet; ■ do not operate the appliance barefooted; ■ do not allow child...
Page 4 - INSTALLATION; This appliance shall only be serviced by authorized personnel.
4 INSTALLATION CAUTION: ■ This appliance must be installed in accordance with these installationinstructions, local gas fitting regulations, municipal building codes, watersupply regulations, electrical wiring regulations, AS5601 / AG 601 - GasInstallations and ony other relevant statutory regulatio...
Page 5 - Figure 1; General Dimensions; Width
5 480 70 60 0 – 2 560 200 0 – 2 200 120 90 Area forelectrical connection Area forgas connection 680 500 Figure 1 DIMENSIONS: (Note: Also refer to Figure 1 above) General Dimensions Width 680 mm Depth 500 mm Depth Below Mounting Surface 33,7 mm Cut-out Dimensions Width 560 mm Depth 480 mm 0 – 2 0 – 2
Page 6 - Figure 2; This appliance shall; not; be used as a space heater, especially if installed in marine
6 750 mm 60 mm min 200 mm min 500 mm 450 mm Figure 2 CLEARANCES: Installation clearances and protection of combustible surfaces shall comply with thecurrent local regulations e.g. AG 601 (AS 5601) - Gas Installations code. Important note: This appliance shall not be used as a space heater, especiall...
Page 7 - minimum clearance of 20 mm; has to be kept between the bottom of the; Overhead clearances; - In no case shall the clearance between the highest; Side clearances; - Where the dimension from the periphery of the nearest; Protection of combustible surfaces; - Local regulations in force specify that; Figure 3
7 The installation shall comply with the dimensions in Figures 1 and 2, bearing in mindthat: ■ A minimum clearance of 20 mm has to be kept between the bottom of the cooking hob and the top of an appliance or a shelf. To ensure this clearancemount the spacers, supplied with the appliance, as shown in...
Page 8 - APPLYING THE SEALS
8 Figure 4a Fig. 4b Figure 4c Fig. 4d Figure 4e APPLYING THE SEALS (Refer to Figures 4): ■ Turn the cooker top upside down. ■ Spread the longer seal “ A ” around the left, rear and right sides as shown in figure 4a. ■ With a cutter or a scissors cut the excess seal “ C ” and retain it for next use (...
Page 10 - Figure 6b; Gas connection for
10 GAS SUPPLY: ■ The connection must be executed by an authorised person according to the relevant standards. ■ Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the gasket has been placed (figures 6a-6b).Conical adaptor and gasket a...
Page 12 - TABLE FOR THE CHOICE OF THE INJECTORS; Natural gas; INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY; : After connection the installer must check that the hose; IMPORTANT WARNING; : The installer shall ensure the hose assembly is
12 TABLE FOR THE CHOICE OF THE INJECTORS Natural gas Universal LPG Test Point Pressure [kPa] 1.0 2.75 BURNER Auxiliary (A) 0.85 3.60 0.53 3.60 Medium-speed burner (SR) 1.12 6.30 0.70 6.30 Rapid burner (R) 1.45 10.30 0.91 10.80 Triple-ring burner (TR) 1.65 13.00 0.95 11.90 Fish burner (PS) 1.12 6.30 ...
Page 13 - CONVERSION PROCEDURE (; to convert to Natural gas or to ULPG; To replace the injectors proceed as follows:; IMPORTANT; Figure 7a
13 CONVERSION PROCEDURE ( to convert to Natural gas or to ULPG ) REPLACING THE INJECTORS The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or Universal LPG (check the “gastype” sticker attached to the appliance). The nomina...
Page 14 - MINIMUM BURNER SETTING ADJUSTMENT; until the flame setting is correct.; Normally for Universal LPG, fully tighten the adjustment screw.; LUBRICATING THE GAS TAP; Servicing of this appliance is only to be carried out by Authori; Figure 8
14 MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit with thegas tap set to the minimum position. If some ports do not light, increase the minimumgas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly ...
Page 15 - ELECTRICAL REQUIREMENTS; suitable for the power consumed by the appliance.
15 INSTALLATION ELECTRICAL REQUIREMENTS ■ The appliance must be connected to the mains checking that the voltage corresponds to the value given in the rating plate and that the electricalcable sections can withstand the load specified on the plate. ■ The plug must be connected to an earthed socket i...
Page 16 - Ignition coil
16 N L M PA CA CA CA CA CA PA PA PA PA N L M PA PA PA PA CA CA CA CA Replacing the power cord must be done by a qualified electrician inaccordance with the instructions supplied by the manufacturer and incompliance with established electrical regulations. Figure 10a 5 gas models Figure 10b 4 gas mod...
Page 17 - USE and CARE
17 USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is to be con-sidered as inappropriate and therefore dangerous. Do not use this appliance asa space heater. ■ Do NOT place ...
Page 18 - CONTROL PANEL; This appliance is class 3 rated; aperture or max gas flow - there is the; GAS HOBS; GAS BURNERS
18 CONTROL PANEL 10. Right semi-rapid burner control knob (1)11. Rapid burner control knob (2)12. Triple-ring burner control knob (3)13. Left semi-rapid burner control knob (4)14. Auxiliary burner control knob (5) ■ This appliance is class 3 rated ■ The appliance has a safety valve system fitted (be...
Page 19 - Fish
19 GAS BURNERS Natural Gas Universal LPG MJ/h MJ/h 1. Semi-rapid burner (SR) 6.30 6.30 2. Rapid burner (R) 10.30 10.80 3. Fish burner (PS) 6.30 6.30 4. Triple ring burner (TR) 13.00 11.90 CONTROL PANEL 10. Semi-rapid burner control knob (1)11. Rapid burner control knob (2)12. Fish burner control kno...
Page 20 - USING GAS BURNERS
20 USING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition (models withelectric ignition). ■ Make sure that all controls are turned to zero. ■ The gas flow to the burner is controlled by the knobs on the safety taps. ■ You control the flow by turning the knob indicator ...
Page 21 - – Adjust the gas valve to the desired position.; Important; To re-light the burner, return the knob to the closed; wait for at; and then repeat the lighting procedure.
21 LIGHTING THE BURNERS(fitted with safety cut-off valve) In order to light the burner, you must: 1 – Models fitted with electric lighter incorporated into the burner knobs : Turn the knob fig. 12 in anti-clockwise direction up to the maximum aperture(symbol ), push in and hold the knob; this will l...
Page 22 - Auxiliary; do not use pans
22 COOKING HINTS FOR GAS HOBS Burners Pan diameter Auxiliary (1) 12 - 14 cm Semi-rapid 16 - 24 cm (2) Rapid 24 - 26 cm Triple ring 26 - 28 cm Fish burner from 12x30 to 18x38 cm Wok max 36 cm (1): with grill for small cookware: minimum diameter 6 cm (2): front right burner, maximum diameter 22 cm ■ T...
Page 23 - When deep fat frying fill the pan only one third full of oil.; cover the pan with a lid and; DO NOT; leave the pan unattended.; DO NOT; use water on the fire.; GRILL FOR SMALL COOKWARE
23 ■ Saucepans with handles which are excessively heavy, in relationship to theweight of the pan, are safer as they are less likely to tip. ■ Pans which are positioned centrally on burners are more stable than thosewhich are offset. ■ It is far safer to position the pan handles in such a way that th...
Page 24 - CORRECT USE OF TRIPLE-RING BURNER; To use the WOK, you must place the wok stand in the; CORRECT; position as; WRONG; MUST BE PLACED ONLY over the pan-rest for
24 CORRECT USE OF TRIPLE-RING BURNER ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK, you must place the wok stand in the CORRECT position as shown in fig. 15. WRONG CORRECT Figure 15 IMPORTANT: The special grille for wok pans (fig. 15) MUST BE PLACED ONLY o...
Page 25 - STAINLESS STEEL HOB; Dry preferably with a microfibre or soft cloth.; Note; BURNERS AND GRIDS; Cleaning and Maintenance
25 GENERAL TIPS ■ Before cleaning the hob switch it off and wait for it to cool down. ■ Clean with a cloth, hot water and soap or liquid detergent. ■ Do not use products which are abrasive, corrosive or chlorine based. ■ Do not use steel pads. ■ Do not leave acid or alkaline substances (vinegar, sal...
Page 26 - CORRECT POSITIONING OF THE BURNERS; Note: To avoid damage to the electric ignition do not use it when the
26 CORRECT POSITIONING OF THE BURNERS ■ It is very important to check that spreader “ F ” and cap “ C ” of the burner (see Figures 16 and 17) are perfectly in place because if they move out of placeserious problems could arise. ■ Make sure that electrode " S " (Fig. 16) is kept clean so that...
Page 27 - CORRECT POSITIONING OF THE TRIPLE-RING BURNER; Then position the cap “
27 CORRECT POSITIONING OF THE TRIPLE-RING BURNER ■ The triple ring burner must be correctly positioned (see fig. 20); the burner rib must be located in position as shown by the arrow (see fig. 18). ■ The burner correctly positioned must not rotate (fig. 19). ■ Then position the cap “ A ” and the rin...
Page 28 - This burner must be correctly positioned as shown in the figure 21.
28 CORRECT POSITIONING OF THE FISH BURNER(model DEGH70WF) ■ This burner must be correctly positioned as shown in the figure 21. Figure 21 T S
Page 29 - LUBRICATION OF THE GAS TAPS
29 LUBRICATION OF THE GAS TAPS ■ If the gas tap becomes stiff, it is necessary to dismantle it carefully and clean it with petroleum spirit. Specialist high temperature resistant grease should beused to lubricate the tap before replacing. ■ The operations must be carried out by an authorised person/...
Page 30 - Service and Maintenance
30 If the ignition spark fails to ignite or does not light the gas, check the followingitems before calling our Customer Service Centre to obtain the nearest AuthorisedService Agent: ■ Burner is reassembled and located correctly. ■ Spark electrode and white ceramic are clean and dry. ■ 240 VAC power...
