DeLonghi DE30WGB - Manuals

N.B. The connection of the appliance to earth is mandatory. If the installation requires alterations to the domestic electrical system call a qualifiedelectrician. He should also check that the socket cable section is suitable for the power drawnby the appliance. Replacing the power cord must be don...

7 The installation shall complywith the dimensions in Figures3 and 4, bearing in mind that: ■ A partition between the base of the hob and thecupboard below should be fitted 0 mm below the workbench surface if the cupboard isto be used for storage. ■ 500 mm 650 mm 450 mm 100 mm minimum between the si...

Figure 6 Figure 7 8 3 cm min 3 cm 4 cm S A R Adhesiveside G G R R FASTENING THE COOKTOP Each cooktop is provided with an instal-lation kit including brackets and screwsfor fastening the cooktop to benches from30 to 40 mm thick.The kit includes four R brackets and four self-threading screws S (figs. ...

GAS SUPPLY: ■ This appliance is suitable for use with Natural Gas or ULPG . (Check the “gas type” sticker attached to the appliance). ■ For Natural Gas the gas supply must be regulated to obtain a pressure of 1 kPa with t burners operating. ■ For ULPG models connect the gas supply directly to the ap...

5. Check the minimum burner setting by quickly rotating the gas control knob from the maximum to the minimum position, the flame must not go out. If adjust-ment is required carry out the “minimum burner setting adjustment" proceduredescribed below. 6. If satisfactory performance cannot be obtain...

(Note: Gas type sticker and data plate are attached to the underside of the base ofthe appliance.) TABLE FOR THE CHOICE OF THE INJECTORS Natural Gas ULPG Test Point 1.0 2.75 Pressure (kPa) Burner Injector Orifice Gas Consumption Injector Orifice Gas Consumption [mm] [MJ/h] [mm] [MJ/h] Semi-rapid 1.1...

Figure 11 Figure 12 12 CONVERSION PROCEDURE (to convert to Natural gas or toULPG) REPLACING THE INJECTORS The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or Universal LPG (check the “gastype” sticker attached to the appli...

Figure 13 13 MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit withthe gas tap set to the minimum position. If some ports do not light, increase theminimum gas rate setting. Check whether the burner remains lit even when the gas tap is turne...

USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is tobe considered as inappropriate and therefore dangerous. Do not use thisappliance as a space heater. ■ Do NOT place combu...

LIGHTING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition. ■ Make sure that all controls are turned to zero. ■ The gas flow to the burner is controlled by a tap incorporating a safety cut-offvalve. If the burner flame should go out for some reason, the safetyvalve will...

LIGHTING GAS BURNERS (FITTED WITH SAFETY CUT-OFF VALVE) In order to light the burner, you must: 1 – Turn the knob fig. 1 7 in anti-clockwise direction up to the maximum aperture, push in and hold the knob; this will light the gas. If there is no mains electricalsupply, bring a lighted match close to...

CORRECT USE OF TRIPLE-RING BURNER - DE30WGB model only ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK you must place the wok stand in the CORRECT position as shown in fig. 20. Figure 21 17 Figure 20 WRONG CORRECT Figure 19 Figure 19

Cleaning and Maintenance 18 GENERAL ADVICE ✓ Before you begin cleaning you must ensure that the hob is switched off. ✓ It is advisable to clean when the appliance is cold and especially when cleaning theenamelled parts. ✓ All enamelled surfaces have to be washed with soapy water or some other non-ab...

ENAMELLED PARTS ✓ All the enamelled parts must be cleaned with a sponge and soapy water only or othernon-abrasive products. ✓ Dry preferably with a soft cloth. ✓ If acid substances such as lemon juice, tomato conserve, vinegar etc. are left on theenamel for a long time they will etch it, making it o...

IMPORTANT WARNING NEVER unscrew the burner plate fixing screws (fig. 22). The burner plates can be removed ONLY by an authorised service agent. Damage to the appliance will occur if not observing this condition and this mayresult in serious injury to the user. The manufacturer declines every respons...

BURNERS AND GRIDS ✓ These parts can be removed and cleaned with appropriate products. ✓ After cleaning, the burners and their flame spreaders must be well dried and correctlyreplaced. ✓ It is very important to check that the burner flame spreader and the cap have been cor-rectly positioned. Failure ...

A B Flamefailureprobe " T " Ignitor " S " CORRECT POSITIONING OF THE TRIPLE RING BURNER Figure 26 Figure 27 Figure 28 Figure 29 ✓ The triple ring burner must be correctlypositioned (see fig. 26 ); the burner ribs must be fitted in their housing asshown by the arrow.The burner correct...

SERVICE AND MAINTENANCE If the ignition spark fails to ignite or does not light the gas, check the followingitems before calling our Customer Service Centre to obtain the nearest AuthorisedDelonghi Service Agent: ■ Burner is reassembled and located correctly. ■ Spark electrode and white ceramic are ...