Crimestopper SP-300 - Manuals

Page 2 - TABLE OF CONTENTS; LED and Valet Programming Button..............................................................................................3; Data Port Diagram ....................................................................................................................16; INSTALLATION CAUTIONS & WARNINGS; WE RECOMMEND; before jump starting, using a battery; DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED; with brake, and gas pedals, steering

2 TABLE OF CONTENTS Installation Cautions & Warnings..…….……………………………….……………………………………….……2 Control Module & Component Mounting ……………...……………………..……………………….…….…..…..3 LED and Valet Programming Button………………………………………………………………………………….3 Wiring………………………………………………………………………..…………………..………….….…….….4-5 S...

Page 3 - CONTROL MODULE & COMPONENT MOUNTING; The

3 CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control module in the engine compartment or where the wiring harness can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed location. The Plac...

Page 4 - WIRING; YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS

4 WIRING GREEN WIRE: (-) NEGATIVE DOOR TRIGGER Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some vehicles may have isolated door triggers. In this case you may need to run additional wires from other doors or go directly to the wire that triggers ...

Page 5 - Connect to RED siren wire from the Siren in the engine compartment.; OUTPUT

5 WIRING BLACK/WHITE WIRE: (-) NEGATIVE DOME LIGHT ILLUMINATION OUTPUT (Optional, requires a relay) This wire provides a (-) negative ground when the system is disarmed to activate a vehicles dome light circuit. We recommend the use of a relay for this connection. Connect Black/W hite to terminal #8...

Page 7 - POWER DOOR LOCK WIRING; NEGATIVE TRIGGER DOORLOCK WIRING; AFTERMARKET MOTOR/DOOR LOCK WIRING

7 POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED ...

Page 8 - TRANSMITTER PROGRAMMING; LED will be on solid.; transmitter for up

8 TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and...

Page 9 - VEHICLE TRANSMITTER PROGRAMMING; PROGRAMMING SECOND VEHICLE:; TRANSMIT ICON

9 2 VEHICLE TRANSMITTER PROGRAMMING PROGRAMMING SECOND VEHICLE: To set up your remote, follow the “Transmitter Programming” steps 1 and 2 (above) In step #3 press the side button on YOUR remote first, for 2-way press and hold for side button until the “2” Icon show on the remote, then press the Lock...

Page 10 - OPTION PROGRAMMING; PROGRAMMING OPTIONS CHART; Data Port Protocol

10 OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times, Siren 5 times, Horn 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/Program button [again] the numbe...

Page 11 - NOTE: Options can be instantly restored to Factory Default Values.

11 OPTION PROGRAMMING NOTE: Options can be instantly restored to Factory Default Values. To restore default values: Perform step #1 (See page 10), then press button 3 (trunk). The siren and horn will chirp 4 times and lights will flash 4 times. Turn OFF Ignition. All programming options will be rest...

Page 12 - DOUBLE UNLOCK PULSE

12 OPTION PROGRAMMING 6. ACTIVE RE-ARMING Active Re-arming allows the system to re-arm itself 30 seconds after disarmed with the transmitter if a door has not been opened. This is handy if the vehicle is accidentally disarmed (via the Transmitter in your pocket) without you knowing it. Note: Active ...

Page 13 - OPTION PROGRAMMING Cont.; CARJACK FEATURES

13 OPTION PROGRAMMING Cont. 14. CARJACK FEATURES This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option. 15. Lock/Unlock or Arm/Disarm with Ignition ON This option allows you Arm and Disarm the system with the Ignition ON. This is used when the...

Page 14 - ANTENNA DIAGRAM; WINDSHIELD; ANTENNA

14 ANTENNA DIAGRAM Antenna should be located at top of widow at least one inch away from metal surface. WINDSHIELD ANTENNA LOCATIONS

Page 15 - WIRING DIAGRAM

15 WIRING DIAGRAM + - + RED WHITE BROWN BLUE/WHITE WHITE/RED ORANGE BLACK/WHITE BLUE GRAY YELLOW BLACK VIOLET GREEN OVERRIDE/ PROGRAM BUTTON BATTERY (-) LOCK OUTPUT +12 VOLT FOR RELAYS (-) UNLOCK OUTPUT GREEN BLUE RED SP-300 (-) NEG. DOOR PIN SWITCH (+) POSITIVE DOOR PIN SWITCH FUSE BOX IGN. SW (-) ...

Page 16 - DATA PORT DIAGRAM; iDATA LINK CABLE; Data Port; Bypass; BCM; OBD connector

16 DATA PORT DIAGRAM iDATA LINK CABLE Data Port Module Not Included Bypass Module 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BCM OBD connector Data wire www.crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2008 Crimestopper Security Products ONLINE TECHNICAL SUPPORT www.crimestopper.com