Crimestopper CS-882 OEM - Manuals

Page 2 - TABLE OF CONTENTS; Installation Modes “A” & “B”.........................................................................................................6-7; INSTALLATION PRECAUTIONS & WARNINGS; BEFORE BEGINNING; with brake, and gas pedals, steering; COMPONENT MOUNTING; Mount button in a hidden but accessible location. It is

TABLE OF CONTENTS Installation Cautions & Component Mounting…….……………….…………………………………………………..2 Wiring………………………………………………………………………………………………..…………….…………3-5 Installation Modes “A” & “B”……………………………………………………………………………………………6-7 System Wiring Diagram………………………………………………………………………………….………………….8 Programmabl...

Page 3 - WIRING; NORMALLY OPEN; BLACK WIRE: SYSTEM CHASSIS GROUND

WIRING (2) VIOLET WIRES: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #1 NORMALLY OPEN These wires come directly from the terminals of an on-board Relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Selected the circuit you want to interrupt, cut it, and connect each cut end to a VIOLET wi...

Page 4 - YELLOW WIRE: +12 VOLTS IGNITION SWITCHED; Connect to door pin activation circuit in vehicle:

WIRING PINK & PINK/WHITE WIRE: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #2 NORMALLY OPEN These wires come directly from the terminals of an on-board relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Select the circuit you want to immobilize, cut it, and connect one end to the Pin...

Page 5 - **SEE DOOR LOCK MOTOR / VALIDATION WIRE CONNECTIONS NEXT PAGE; The sensor supplied with this system does not

WIRING GREEN WIRE: (-) HOOD/TRUNK TRIGGER Connect this wire to a grounding hood / trunk pin switch or to existing factory hood and trunk pin switches that read ground when open. If no existing switches are available, new pin switches may be installed. Note: DO NOT mount new pin switches in water pat...

Page 6 - MODE A; is the default mode and is used for most vehicles.

NEGATIVE VALIDATION INPUTS (TOP EDGE OF 882 MODULE) POSITIVE VALIDATION INPUTS (TOP EDGE OF 882 MODULE) INSTALLATION MODE “A” (Most Vehicles) MODE A is the default mode and is used for most vehicles. This mode requires 4-Wires to be connected for proper operation: Yellow/Black and Blue/Black connect...

Page 7 - INSTALLATION MODE “B”; MODE B; Unlock

INSTALLATION MODE “B” MODE B is used for vehicles with single wire locking systems that are often called “Data Bus” or “Multi-Plex” vehicles. These vehicles include many late model Dodge/Chrysler Vehicles, 2003 GM Truck, SUV’s, and 1996-2003 Jeep Grand Cherokee, and others. This mode must be program...

Page 8 - SYSTEM WIRING DIAGRAM

SYSTEM WIRING DIAGRAM VALE T/ IGN SW. STARTER S TATUS LE D FUSE BOX IGNITION ON &CRANKING VOLTAGE STARTER WIRE 85 87A CUT 86 30 RED VIOLET BLACK WHITE/RED (-) ARMED OUTPUT(STARTER DISABLE) IGN SW. ORANGE WHITE FUSE 15A PARKING LIGHTS SHO CK SENSOR BATTERY PROGRAM BUTTON + IMMOBILIZE (Low-Current...

Page 9 - PROGRAMMABLE OPTIONS; OPTION PROGRAMMING CHART; DOOR WARNING DELAY

PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 7 times within 10 seconds. 2. Turn OFF Ignition. LED will flash slowly once per second as and indicator the system is in programming mode. 3. Within 20 seconds, press the Override/Program button the number of times th...

Page 10 - DOOR TRIGGER POLARITY

PROGRAMMABLE OPTIONS 6. SIREN/HORN CONFIRMATION This option controls whether the CS-882OEM system pulses the siren/horn for an audible lock/unlock confirmation. If your vehicle already chirps the horn when using the keyless entry remotes, then you may choose to disable this option. 8. PASSIVE ARMING...

Page 11 - OPERATING INSTRUCTIONS; ARMING

OPERATING INSTRUCTIONS ARMING To arm the alarm and lock the doors, press the Lock button of your Factory Keyless Remote Control. The 882 OEM system will sense the Door Lock signal and Arm. The lights will flash once, the vehicle horn or siren will chirp once. After 3 seconds, the LED indicator will ...

Page 12 - OPERATING INSRUCTIONS; VALET MODE

OPERATING INSRUCTIONS VALET MODE To disable alarm functions of the 882 system, turn the Ignition ON and press the override/program button 3 times within 8 seconds. After 8 seconds, the dash LED turns on solid as an indicator that the system is in valet mode. Repeat this steps to exit VALET mode. The...