Crimestopper CS-2000DP-TW2 - Manuals

Crimestopper CS-2000DP-TW2 – Manual in PDF format online.

Manuals:

Manual

Manual Crimestopper CS-2000DP-TW2

Summary

Page 2 - TABLE OF CONTENTS; Data Port Diagram ......................................................................................................................8; INSTALLATION CAUTIONS & WARNINGS; BEFORE BEGINNING; before jump starting, using a battery; DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED; with brake, and gas pedals, steering

2 TABLE OF CONTENTS Installation Cautions & Warnings..…….……………………………….……………………………………….……2 Control Module & Component Mounting ……………...……………………..……………………….…….…..…..3 Wiring (LED, PROGRAM BUTTON AND SHOCK SENSOR page 5-6)…………………..………….….…..….3-6 Power Door Lock Wiring……………………………………………………….…………...

Page 3 - CONTROL MODULE & COMPONENT MOUNTING; Mount the red LED in a visible location on the dashboard or console.; WIRING

3 CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control unit in the engine compartment or where the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a con...

Page 4 - BLACK WIRE: SYSTEM CHASSIS GROUND

4 WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 V...

Page 5 - Connect to RED siren wire from the Siren in the engine compartment.; OUTPUT; VALET / PROGRAM SWITCH

5 WIRING BLUE/WHITE WIRE: NOT USE BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) Connect to RED siren wire from the Siren in the engine compartment. WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT Connect to the switched parking light wire at back of light switch. If this is not possible, connect directly...

Page 6 - WIRING: SHOCK SENSOR; The sensor supplied; POWER DOOR LOCK WIRING; SENSOR ADJUSTMENT

6 WIRING: SHOCK SENSOR 4 PIN SENSOR PLUG/HARNESS (BLUE): White Wire: Negative Trigger Blue W ire: Negative W arn-away Black Wire: Sensor Ground Red W ire Sensor Power SHOCK SENSOR: The sensor supplied with this system does not require any additional wiring. Simply mount the sensor in a suitable loca...

Page 7 - NEGATIVE TRIGGER DOORLOCK WIRING; AFTERMARKET MOTOR/DOOR LOCK WIRING

7 POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED ...

Page 8 - DATA PORT DIAGRAM; iDATA LINK CABLE; Data Port; OFA; BCM; OBD connector

8 DATA PORT DIAGRAM Data bus Systems: Data Controlled door locks, Factory Security and many accessories Data bus systems send low current “Data messages” to the door lock controllers, BCM, and Factory security in order to lock and unlock doors, Bypass factory security system and much more. To instal...

Page 9 - TRANSMITTER PROGRAMMING; LED will be on solid.; transmitter for up; VEHICLE TRANSMITTER PROGRAMMING; PROGRAMMING SECOND VEHICLE:

9 TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and...

Page 10 - OPTION PROGRAMMING; PROGRAMMING OPTIONS CHART

10 OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times, Siren 5 times, Horn 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/Program button [again] the numbe...

Page 11 - Doors will not lock if they are open to prevent locking the keys in

11 OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Ar...

Page 12 - DOUBLE UNLOCK PULSE

12 OPTION PROGRAMMING 7. DOUBLE UNLOCK PULSE With this feature enabled, the unit will send 2 unlock pulses when the #2 Unlock button is pressed. 2 pulses are required for interfacing into some existing Factory Keyless Entry or Alarm systems on vehicles such as Nissan, VW , Toyota, and Lexus vehicles...

Page 14 - OPERATING INSTRUCTIONS (REMOTE OPERATIONS); ONE WAY SIDEKICK REMOTE:; BUTTON FUNCTIONS; Press & Hold for more than 3 sec. to activate “Panic” feature.; LOCK

14 OPERATING INSTRUCTIONS (REMOTE OPERATIONS) ONE WAY SIDEKICK REMOTE: The transmitter supplied with the CS-2000DP-TW 2 system has four buttons. The button configuration of the CS-2000DP-TW 2 is Factory-set and unchangeable. See second vehicle operation for additional information on how to use your ...

Page 15 - BUTTON 5; Press and release to light up

15 BUTTON 5 (On side of remote): · Press and release to light up the LCD screen. · Press and release twice to recall the last message from the LCD screen. · Press and Hold two seconds to change from Car 1 to Car 2 or Car 2 to Car 1. · Press 5 times to change the Time and audible beep tones on the re...

Page 16 - OPERATION INSTRUCTIONS (LCD PANEL FUNCTIONS SHOWN)

16 1 ST AUX. OUTPUT TRUNK POP (FLASH) (OR HOOD OPEN) OPERATION INSTRUCTIONS (LCD PANEL FUNCTIONS SHOWN) VALET DATA TRANSLATE IGN TRIGGER (FLASH) WARN AWAY (FLASH) SHOCK SENSOR(FLASH) SETTING THE CLOCK (2-WAY – LCD REMOTE) 1. Press button #5 (recall) on the side of the remote control 5 times. 2. The ...

Page 17 - OPERATION INSTRUCTIONS; ALARM TRIGGERING

17 OPERATION INSTRUCTIONS ACTIVE ARMING To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features a...

Page 18 - OPERATING INSTRUCTIONS; SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL

18 OPERATING INSTRUCTIONS SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL This system can be armed and disarmed without siren chirps on an “as needed” basis. Press and release Button #4 for arm/disarm without siren chirps. PROGRAMMABLE SILENT ARM/DISARM MODE (CHIRP DEFEAT) The system can be silen...

Page 19 - PRIOR INTRUSION ALERT; Doors will not lock if they are open to

19 OPERATING INSTRUCTIONS PRIOR INTRUSION ALERT If the system was tripped in your absence, the dash LED will be flashing rapidly. W hen the system is disarmed you will hear 3 chirps (and 3 light flashes). Carefully inspect your vehicle to see if there is any damage or a theft has occurred. DOME LIGH...

Page 20 - CARJACK PROTECTION FEATURES; ACTIVE CARJACK

20 CARJACK PROTECTION FEATURES ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 10. W hen the Ignition is on (vehicle is running), press and hold button #3 (AUX) for 3 seconds. Parking lights will flash TWICE...

Page 21 - ANTENNA DIAGRAM; WINDSHIELD

21 ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCATIONS Black Plug White Plug RECOMMENDED Transceiver Box & Antenna CS-2000DP-TW2 Antenna System CS-2000DP-TW2 DATA PORT ANNTENA PLUG

Page 22 - WIRING DIAGRAM

22 WIRING DIAGRAM + - + RED WHITE BROWN BLUE/WHITE WHITE/RED ORANGE BLACK/WHITE BLUE GRAY YELLOW BLACK VIOLET GREEN LED OVERRIDE/ PROGRAM BUTTON BATTERY (-) LOCK OUTPUT +12 VOLT FOR RELAYS (-) UNLOCK OUTPUT GREEN BLUE RED CS-2000DP-TW2 (-) NEG. DOOR PIN SWITCH (+) POSITIVE DOOR PIN SWITCH FUSE BOX I...

Page 23 - LOW BATTERY WARNING – LCD REMOTE; LOW BATTERY WARNING; Replacing the Battery

23 LOW BATTERY WARNING – LCD REMOTE LOW BATTERY WARNING The CS-2000DP-TW 2 LCD have a low battery warning system. W hen the battery voltage is low. The LCD pager remote will show a low voltage icon. W e recommend replacing the battery for proper operation. To replace the battery, simply unlatch and ...