Chicago Electric 95283 - Manuals

Chicago Electric 95283 – Manual in PDF format online.

Manuals:

Manual

Manual Chicago Electric 95283

Summary

Page 2 - WORK AREA

PRODUCT SPECIFICATIONS SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating,inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keepyour invoice with this manual. Write the invoice number on the inside of the front cove...

Page 3 - sparks which may ignite the dust or fumes.

PERSONAL SAFETY 1. Stay alert. Watch what you are doing, and use common sense whenoperating a power tool. Do not use a power tool while tired or under theinfluence of drugs, alcohol, or medication. A moment of inattention whileoperating power tools may result in serious personal injury. 2. Dress pro...

Page 4 - SPECIFIC SAFETY RULES AND PRECAUTIONS; IMPORTANT! Your Warranty is voided if:

any other condition that may affect the tool’s operation. If damaged, havethe tool serviced before using. Many accidents are caused by poorlymaintained tools. SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 4 6. Use only accessories that are recommended by the manufacturer for you...

Page 5 - KICKBACK PRECAUTIONS

6. Always plan carefully where a tree limb will fall to avoid damage to propertyand/or personal injury. 7. Never stand directly beneath the limb you are cutting. Always stand well offto the side. 8. Do not use the Polesaw/Pruner to cut anything except tree limbs andbrush. 9. Always maintain a firm g...

Page 6 - ELECTRICAL PRECAUTIONS; NEVER use the Polesaw/Pruner in damp or wet conditions.; CARBON MONIXIDE PRECAUTIONS; Keep the Polesaw/Pruner and surrounding areas clean at all times.

not allow the nose of the Guide Bar to contact a log, branch, fence, or anyother obstruction while you are operating the tool. B. Always cut with the Engine running at full speed. Fully squeeze the Throttle and maintain a steady cutting speed. C. Always keep the Chain clean and sharp. D. Keep all gu...

Page 7 - Use only Engine manufacturer recommended fuel and oil.; MECHANICAL PRECAUTIONS

Dispose of fluids and cleaning materials as per any local, state, or federal codesand regulations. Store oil rags in a covered metal container. 4. Never store fuel or other flammable materials near the Polesaw/Pruner. 5. Do not smoke, or allow sparks, flames, or other sources of ignition aroundthe P...

Page 8 - around the Polesaw/Pruner when it is running.; UNPACKING; FIGURE A

around the Polesaw/Pruner when it is running. SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 8 MISC. PRECAUTIONS 1. DANGER! We recommend that people with pacemakers not use this tool.This tool produces strong electromagnetic fields that can cause interference to orfailure of the ...

Page 9 - PRODUCT FEATURES; FIGURE B

PRODUCT FEATURES 3 3 7 8 3 1 2 1 0 1 4 87A 3 9 7 4 7 3 5 0 6 9 55A 48A 4A 78A 42A FIGURE B 7 7 1. Top Pipe Support (33): Prior to using the Polesaw/Pruner, always check tomake sure all other connecting parts are firmly secured to the Top Pipe Support.(See Figure B.) 2. Guard Bar Cover (78): Make sur...

Page 10 - until sag does not exist. Then, retighten the; “Pre-Start Instructions” section of this; when cold, must be primed with fuel prior to

5. Bottom Pipe Support (2): Always hold the Polesaw/Pruner firmly with bothhands. Keep your left hand on the front portion of the Bottom Pipe Support andyour right hand on the rear portion of the Bottom Pipe Support, so that yourbody is to the left of the chain line. Never use a left-handed (cross-h...

Page 11 - “Pre-Start Instructions” section in this manual for; position. When starting a; “Pre-Start Instructions” section in this manual for full details on; PRE-START INSTRUCTIONS; To Fill The Chain Oil Tank:

13. Oil Tank (69): Refer to the “Pre-Start Instructions” section in this manual for full details. (See Figure B.) 14. Gear Box Grease Fitting (50): The Drive Gear (44) assembly should be filled(through the Gear Box Grease Fitting) with clean, new, automotive axle greaseevery three months or 50 hours...

Page 12 - To Fill The Fuel Tank:; OPERATING INSTRUCTIONS

SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 12 To Fill The Fuel Tank: 1. IMPORTANT! Your warranty is voided if:You do not operate the Polesaw/Pruner with the proper 50:1 fuel mix in itsFuel Tank (78A). Never run the Engine (1) with an improper fuel mix, low or nofuel mix. Runn...

Page 16 - FIGURE C

the Drive Gear (44) and into the Guard Bar groove. The cutters on the top ofthe Guard Bar should face toward the Guard Bar tip, in the direction of thechain rotation. Replace the Chain Saw Cover and secure with the Nut. Tightenthe Nut finger tight only to allow for tension adjustment.Then, follow di...

Page 18 - D e scription

PARTS LIST - POLESAW/PRUNER UNIT NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 18 Pa rt # D e scription P art # D e scription 1 Engine Assembly 43 Washe...

Page 21 - ASSEMBLY DIAGRAM -ENGINE

ASSEMBLY DIAGRAM -ENGINE SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 21 42A 41A 40A 43A 44A 45A 46A 47A 48A 52A 51A 50A 49A 53A 54A 55A 86A 56A 57A 58A 59A 60A 61A 62A 63A 64A 84A 12A 13A 14A 15A 16A 71A 71A 72A 73A 1A 2A 3A 4A 5A 6A 7A 8A 9A 10A 11A 83A 70A 69A 67A 66A 68A 74...

Page 22 - Emission Control System Warranty

SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 22 Emission Control System Warranty U n i t e d S t a t e s E m i s s i o n C o n t ro l D e fe c t s Wa r r a n t y S t a t e m e n t T h e U n i t e d S t a t e s E nv i r o n m e n t a l P r o t e c t i o n A g e n c y ( h e r e i...

Page 23 - WARRANTY; LIMITED

SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 23 5 . S e r v i c e a n d M a i n t e n a n c e C o m p o n e n t p a r t s w h i c h a r e n o t s c h e d u l e d fo r r e p l a c e m e n t a s r e q u i r e d m a i n t e n a n c e o r a r e s c h e d u l e d o n l y fo r r e g ...