Chicago Electric 94626 - Manuals

Page 2 - SPECIFICATIONS; SAVE THIS MANUAL; GENERAL SAFETY RULES; SAVE THESE INSTRUCTIONS; Work Area; Keep your work area clean and well lit.; Cluttered benches and dark areas invite

Page 2 SKU 94626 For technical questions, please call 1-800-444-3353 SPECIFICATIONS SAVE THIS MANUAL You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the in...

Page 3 - Electrical Safety; Do not expose power tools to rain or wet conditions.; Personal Safety; Avoid accidental starting.

Page 3 SKU 94626 For technical questions, please call 1-800-444-3353 Electrical Safety 4. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 5. Do not expose power tools to rain or wet ...

Page 5 - SPECIFIC SAFETY RULLES FOR THIS PRODUCT

Page 5 SKU 94626 For technical questions, please call 1-800-444-3353 SPECIFIC SAFETY RULLES FOR THIS PRODUCT 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep yo...

Page 8 - either a two or three wire extension cord.

Page 8 SKU 94626 For technical questions, please call 1-800-444-3353 Double Insulated Tools with Two Prong Plugs 4. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the p...

Page 9 - SYMBOLOGY; UNPACKING

Page 9 SKU 94626 For technical questions, please call 1-800-444-3353 SYMBOLOGY Table B UNPACKING When unpacking, check to make sure that all the parts are included. The unit comes fully assembled. Refer to the Assembly section, and the Assembly Drawing and Parts List at the end of this manual. If an...

Page 10 - Place the Saw where the flush cut is to be made. See photo below.

Page 10 SKU 94626 For technical questions, please call 1-800-444-3353 Controls Making Flush Cuts 1. Place the Saw where the flush cut is to be made. See photo below. When making a cut under a toe-kick (i.e., under a cabinet), insert the Saw at an angle, then lower it to the floor surface. See illust...

Page 11 - Replacing the Carbon Brushes

Page 11 SKU 94626 For technical questions, please call 1-800-444-3353 Caution: Never pull the Saw backwards since the Saw Blade will climb out of the cut and kickback will occur. INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Trigger Switch of the Flush Cut Saw is in its “OFF” position...

Page 12 - Installing the Saw Blade; clockwise using the Hex Wrench with the other hand.; TROUBLESHOOTING

Page 12 SKU 94626 For technical questions, please call 1-800-444-3353 Installing the Saw Blade 1. Use only a 3-3/8 inch Saw Blade (2) rated to at least 4500 RPM. 2. Unplug the Saw Power Cord (54) from the electrical outlet. 3. Wearing work gloves, raise the Blade Guard (6) as far as possible. 4. Hol...

Page 13 - PLEASE READ THE FOLLOWING CAREFULLY

Page 13 SKU 94626 For technical questions, please call 1-800-444-3353 NOTE : Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM ...

Page 14 - ASSEMBLY DRAWING

Page 14 SKU 94626 For technical questions, please call 1-800-444-3353 ASSEMBLY DRAWING

Page 15 - LIMITED 90 DAY WARRANTY; vary from state to state.

Page 15 SKU 94626 For technical questions, please call 1-800-444-3353 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials...