Chicago Electric 94362 - Manuals

Page 2 - Cluttered benches and dark areas

Page 2 SKU 94362 For technical questions, please call 1-800-444-3353. PRODUCT SPECIFICATIONS SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating,inspection, maintenance and cleaning procedures, parts list and assembly diagram.Keep your invoice with...

Page 5 - SERVICE; Service; “Inspection, Maintenance, And Cleaning” section of this; may create a risk of electric shock or injury.; GROUNDING; outlet installed by a qualified electrician.

Page 5 SKU 94362 For technical questions, please call 1-800-444-3353. 22. Check for misalignment or binding of moving parts, breakage of parts, andany other condition that may affect the tool’s operation. If damaged, havethe tool serviced before using. Many accidents are caused by poorly maintained ...

Page 7 - EXTENSION CORDS; Grounded; tools require a three wire extension cord.; Double Insulated; tools; RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*; FIGURE C

Page 7 SKU 94362 For technical questions, please call 1-800-444-3353. EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gaugeexte...

Page 8 - SYMBOLOGY; SPECIFIC SAFETY RULES

Page 8 SKU 94362 For technical questions, please call 1-800-444-3353. SYMBOLOGY V ~ A xxxx/min. Double Insulated Canadian StandardsAssociation UnderwritersLaboratories, Inc. Volts Alternating Current Amperes No Load Revolutionsper Minute (RPM) no SPECIFIC SAFETY RULES 1. Maintain a safe working envi...

Page 12 - Sparking Hazard.; Some metal cutting will create sparks. Do not; UNPACKING; People with pacemakers should consult their physician(s) before; Parts Lists on pages 20

Page 12 SKU 94362 For technical questions, please call 1-800-444-3353. 34. Maintain this product with care. Keep this product clean for better and safer performance. 35. Maintenance: For your safety, service and maintenance should be performed regularly by a qualified technician. 36. Check for damag...

Page 13 - ASSEMBLY INSTRUCTIONS

Page 13 SKU 94362 For technical questions, please call 1-800-444-3353. ASSEMBLY INSTRUCTIONS NOTE: For additional information regarding the parts mentioned in the following pages, refer to the Assembly Diagram on page 22. To Attach The Rip Guide, And Adjust The Width Of A Cut: 1. WARNING! Prior to p...

Page 15 - Remove the; FIGURE H; FIGURE G

Page 15 SKU 94362 For technical questions, please call 1-800-444-3353. 3. Turn the Knob (1) and remove the Plastic Cover (2). (See Figure F.) 4. Remove the three phillips Screws (33) located on the left side of the Body (32). (See Figure G.) 5. Depress the Depth Control Lever (52) and lower the Base...

Page 16 - FIGURE I; Replace the

Page 16 SKU 94362 For technical questions, please call 1-800-444-3353. 6. Depress the Depth Control Lever (52) to hold the Saw Blade (10) in place. Usethe Blade Wrench (74) to unscrew and remove the Bolt (8). Release pressure onthe Blade Lock Lever. (See Figure I.) 7. Remove the Outer Flange (11). T...

Page 17 - gradually into the workpiece.; Proper Operation During The Cutting Process:; Never pass hands and fingers directly in front of, to the rear, or

Page 17 SKU 94362 For technical questions, please call 1-800-444-3353. 3. Make sure the workpiece is supported at all times. Whenever possible, securethe workpiece in a vise or with clamps (not included). If necessary, use a rollerstand (not included) with larger workpieces. 4. Before trying new or ...

Page 18 - Inspect the general condition of the Saw. Check for; Do not use damaged equipment.; INSPECTION AND MAINTENANCE; Always unplug the Saw from its electrical outlet before; The Saw Blade (10) must be sharp and clean to perform properly.; To Install A Saw Blade”; With a vacuum or compressed air, remove all metal debris from the; FIGURE J

Page 18 SKU 94362 For technical questions, please call 1-800-444-3353. 2. Before each use: Inspect the general condition of the Saw. Check for misalignment or binding of moving parts, loose, cracked or broken parts,damaged wiring, and any other condition that may affect its safe operation. Ifabnorma...

Page 19 - both Carbon Brushes immediately with approved; FIGURE K

Page 19 SKU 94362 For technical questions, please call 1-800-444-3353. 6. Store the Saw in a clean, dry location. If the Carbon Brushes appear to be in good condition, but only dirty, they can becleaned by rubbing with a pencil eraser. If there are large scratches on theCarbon Brushes, replace both ...

Page 20 - PARTS LIST; Description

Page 20 SKU 94362 For technical questions, please call 1-800-444-3353. PARTS LIST *NOTE: PARTS #32* THROUGH 41* MAY NOT BE ORDERED INDIVIDUALLY, BUT MUST BE ORDERED AS A COMPLETE MOTOR ASSEMBLY (PART #76*). 1 Knob 28 Baffle 2 Plastic 29 Rip Guide Pin 3 Screw (M5) 30 Screw (M5) 4 Transparent Panel 31...

Page 21 - PLEASE READ THE FOLLOWING CAREFULLY

Page 21 SKU 94362 For technical questions, please call 1-800-444-3353. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PARTS LIST (CONTINUED) PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PRO...

Page 22 - ASSEMBLY DIAGRAM; LIMITED 90 DAY WARRANTY

Page 22 SKU 94362 For technical questions, please call 1-800-444-3353. ASSEMBLY DIAGRAM *NOTE: PARTS #32* THROUGH 41* MAY NOT BE ORDERED INDIVIDUALLY, BUT MUST BE ORDERED AS A COMPLETE MOTOR ASSEMBLY (PART #76*). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32*...