Chicago Electric 93188 - Manuals

Page 2 - SPECIFICATIONS; SAVE THIS MANUAL; READ AND UNDERSTAND ALL INSTRUCTIONS; Work Area; Keep your work area clean and well lit.; Cluttered benches and dark areas invite accidents.

Page 2 SKU 93188 For technical questions, please call 1-800-444-3353 SPECIFICATIONS Construction Formed and Welded Steel with Heavy Duty Motor and Steel Drum Features Forward / Reverse GearsAluminum Friction ClutchCable Lockdown Electric Motor Heavy Duty 120 V~ 1/3 HP1785 RPM Power Required 120 V~ /...

Page 3 - Electrical Safety; Do not expose power tools to rain or wet conditions.; Personal Safety; Do not overreach. Keep proper footing and balance at all times.

Page 3 SKU 93188 For technical questions, please call 1-800-444-3353 Electrical Safety Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and 1. refrigerators. There is an increased risk of electric shock if your body is grounded. Do not expose power tools to rain or wet con...

Page 4 - SPECIFIC SAFETY RULES FOR THIS PRODUCT

Page 4 SKU 93188 For technical questions, please call 1-800-444-3353 Use safety equipment. Always wear eye protection. 6. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Tool Use and Care Do not force the tool. Use the correct tool for your a...

Page 6 - GROUNDING; GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS; FIGURE A; DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

Page 6 SKU 93188 For technical questions, please call 1-800-444-3353 could cause interference to or failure of the pacemaker. In addition, people with pacemakers should adhere to the following: • Avoid operating power tools alone. • Properly maintain and inspect all tools before use to avoid electri...

Page 7 - ExTENSION CORDS; Grounded

Page 7 SKU 93188 For technical questions, please call 1-800-444-3353 standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) Double insulated tools may be used in either of the 120 volt outlets shown in the pre- 2. ceding ill...

Page 8 - RECOMMENDED MINIMUM WIRE GAUGE FOR ExTENSION CORDS*; NAMEPLATE; FIGURE C; SYMBOLOGY

Page 8 SKU 93188 For technical questions, please call 1-800-444-3353 If you are using one extension cord for more than one tool, add the nameplate 5. amperes and use the sum to determine the required minimum cord size. (See Figure C.) If you are using an extension cord outdoors, make sure it is mark...

Page 9 - OPERATING INSTRUCTIONS; Cleaner, as well as its operation and application.; Operational Components and Controls; Motor; The; Motor Direction Switch; The Motor is controlled by a; Foot Switch; The Foot Switch is in a rubber boot

Page 9 SKU 93188 For technical questions, please call 1-800-444-3353 OPERATING INSTRUCTIONS The following sections describe the operational components and controls of the Drain Cleaner, as well as its operation and application. Operational Components and Controls Warning: Do not allow your hands, cl...

Page 10 - Select and Attach Proper Cutting Tool; Cutter Tool

Page 10 SKU 93188 For technical questions, please call 1-800-444-3353 Foot Switch (14): Press On, release Off Direction Lever (44-16): Pull Up: forward direction, Center: neutral; Push down: slow reverse, Fast reverse direction. Attaching Guide Spring (48) While following these procedures, it may be...

Page 11 - Drain Cleaning Operation; Place the Drain Cleaner within two feet of the drain pipe inlet.; Do not; After the drain pipe has been opened, return the cable to the Drum.

Page 11 SKU 93188 For technical questions, please call 1-800-444-3353 REV 07d, 07f, 08e Drain Cleaning Operation CAUTION: DO NOT USE THIS DRAIN CLEANER ON DRAIN LINES SMALLER THAN TWO INCHES. DAMAGE MAY OCCUR TO EQUIPMENT OR PIPES. Place the Drain Cleaner within two feet of the drain pipe inlet. 1. ...

Page 12 - OPERATING TIPS; TROUBLESHOOTING; Problem; Allow motor to cool off com-

Page 12 SKU 93188 For technical questions, please call 1-800-444-3353 REV 08a, 08e When Cable starts to bend, twist or whip Too much slack in Cable or cutter tool caught in stoppage. Re-lease Foot Switch, press Direction Lever down to temporarily reverse cable feed direction, and re-wind to relieve ...

Page 14 - Make sure the Power Switch of the Drain Cleaner is in its “OFF”; General; Do not use; Periodically recheck all nuts, bolts, and screws for tightness.; Auto Feed Maintenance; Flushing with water,; If disassembly is required, proceed

Page 14 SKU 93188 For technical questions, please call 1-800-444-3353 INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch of the Drain Cleaner is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cl...

Page 15 - PLEASE READ THE FOLLOWING CAREFULLY; Guide Wheel Replacement; need replacement. Replace all three Guide Wheels at the same time.; Tangled Cable; cause the Cable to tangle in the Drum.

Page 15 SKU 93188 For technical questions, please call 1-800-444-3353 PLEASE READ THE FOLLOWING CAREFULLY T H E M A N U FAC T U R E R A N D / O R D I S T R I BU TO R H A S P ROV I D E D T H E PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY RE...

Page 16 - MAIN UNIT PARTS LIST

Page 16 SKU 93188 For technical questions, please call 1-800-444-3353 MAIN UNIT PARTS LIST Part Description Q’ty 1 Protect Shield 1 2 Belt 6PK1145 1 3 Belt Wheel 1 4 Bolt M6 x 16 1 5 Main Switch 1 6 Lock Nut M6 1 7 Motor 1 8 Lock Nut M10 6 9A Motor Holder 1 10 Spring 4 14 Foot Switch 1 15 GFCI 1 16A...

Page 17 - MAIN UNIT ASSEMBLY DRAWING

Page 17 SKU 93188 For technical questions, please call 1-800-444-3353 MAIN UNIT ASSEMBLY DRAWING REV 08/06

Page 18 - 4-4A Axle for Press Wheel

Page 18 SKU 93188 For technical questions, please call 1-800-444-3353 PARTS LIST FOR SUBASSEMBLY NO. 44A (FEED UNIT) Part Description Q’ty 44-1 Base 1 44-2 Inner Hex Bolt M6x14 6 44-3 Adapter 1 44-4A Axle for Press Wheel 1 44-5A Guide Screw 1 44-6 Cable Sleeve 1 44-7A End Cap 1 44-8A Screw 4 44-9 Pr...

Page 19 - LIMITED 1 YEAR WARRANTY; vary from state to state.

Page 19 SKU 93188 For technical questions, please call 1-800-444-3353 LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials...