Chicago Electric 91995 - Manuals

Page 2 - SPECIFICATIONS; UNPACKINg; When unpacking, check to make sure all the parts shown on the; Parts list on; SAVE THIS MANUAl; gENERAl SAFETY RUlES; WARNINg! Read all instructions; The term “power tool” in all of the warnings listed; SAVE THESE INSTRUCTIONS; WORK AREA; Keep your work area clean and well lit.; Cluttered benches and dark areas; Do not operate power tools in explosive atmospheres, such as in the; Power tools create sparks

Page 2 SKU 91995 For technical questions, please call 1-800-444-3353. SPECIFICATIONS Electrical Requirements 120 V / 60 Hz / 1800 Input Watts.15.0 AMPs Start Up / 5300 RPM No Load.Three Prong, Grounded, Power Cord Plug.Power Switch Type: Squeeze Type. Saw Blade (Included) Diameter/Type 10” Diameter ...

Page 4 - TOOl USE AND CARE

Page 4 SKU 91995 For technical questions, please call 1-800-444-3353. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. Remove adjusting key...

Page 9 - gROUNDINg; Check with a qualified electrician if you are in doubt as to; grounded Tools: Tools with Three Prong Plugs; Grounded; WARNINg

Page 9 SKU 91995 For technical questions, please call 1-800-444-3353. gROUNDINg Improperly connecting the grounding wire can result in electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with...

Page 10 - sure each cord contains at least the minimum wire size required.; RECOMMENDED MINIMUM WIRE gAUgE FOR EXTENSION CORDS*; Symbology

Page 10 SKU 91995 For technical questions, please call 1-800-444-3353. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 1 gauge cord. (See Table A.) When using more than one extension cord to make up the to...

Page 11 - ASSEMBlY AND OPERATINg INSTRUCTIONS; Assembly Diagram on page 24.; arrow

Page 11 SKU 91995 For technical questions, please call 1-800-444-3353. ASSEMBlY AND OPERATINg INSTRUCTIONS Note: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 24. To Replace And Install A Saw Blade: WARNINg! Prior to performing any assemb...

Page 12 - CAUTION! The Cross Pin (28) should always be activated in the “locked; The Cross Pin allows the operator to lock the Saw Blade in position,; FIgURE E

Page 12 SKU 91995 For technical questions, please call 1-800-444-3353. CAUTION! The Cross Pin (28) should always be activated in the “locked down” position when the Saw is not being used and when the Saw is being transported. The Cross Pin should be activated in the “locked up” position only when ch...

Page 13 - FIgURE g

Page 13 SKU 91995 For technical questions, please call 1-800-444-3353. . Depress the Spindle Lock (4) to keep the Saw Blade (5) from turning. (See Figure H.) . Loosen the Screw (4) that holds the Large Cover (4) in place. Then, use the Wrench (110) to remove the Bolt (50). (See Figure g.) . Rotate t...

Page 14 - pointing

Page 14 SKU 91995 For technical questions, please call 1-800-444-3353. 9. Use the Wrench (109) to unscrew and remove the Spindle Bolt (5). NOTE: The Spindle Bolt unscrews in a clockwise direction. Then, remove the Outer Flange (5). (See Figure I.) 11. Wearing heavy duty work gloves to avoid accident...

Page 15 - To Assemble Additional Accessories:; FIgURE K; Safety Cover rotates back out of the way.; Do not disconnect or remove the Safety Cover (53). Do not operate the

Page 15 SKU 91995 For technical questions, please call 1-800-444-3353. 1. A workpiece Clamp Assembly (3) can be installed by inserting the Assembly into the hole located in the Guide Fence (3). Once inserted, lock the Assembly in place with the Thumb Screw (35). To clamp the workpiece to the Base ()...

Page 16 - Never disconnect

Page 1 SKU 91995 For technical questions, please call 1-800-444-3353. cannot be seen clearly, disconnect the electrical Power Cord from its electrical outlet and clean the Safety Cover with a soft, damp, cloth. A mild detergent may be used, but do not use solvents which may damage the Safety Cover. ...

Page 17 - To Adjust The Cutting Depth:; WARNINg! Prior to performing this procedure, make sure the Power; Miter Saw is in operation.; FIgURE N

Page 1 SKU 91995 For technical questions, please call 1-800-444-3353. To Adjust The Cutting Depth: 1. WARNINg! Prior to performing this procedure, make sure the Power Cord (102) of the Miter Saw is unplugged from its electrical outlet. The Dust Bag: 1. The Dust Bag (93) catches and holds the wood ch...

Page 18 - To Adjust The Miter Angle:; To Adust The Bevel Of Cut:

Page 1 SKU 91995 For technical questions, please call 1-800-444-3353. HANDlE (1) . If the Saw Blade (5) touches the Table (1) or any other part of the Saw Base (), tighten the Screw (92) to raise the Saw Blade slightly until it clears. (See Figure O.) To Adjust The Miter Angle: 1. WARNINg! Prior to ...

Page 19 - Make sure the Power Cord (102) of the Miter Saw is unplugged from its; Then, if necessary, make adjustments to the workpiece Holder; FIgURE P

Page 19 SKU 91995 For technical questions, please call 1-800-444-3353. o 2. The bevel angle (or Saw Blade tilt capacity) may be adjusted from 0 - 45 to the left. To do so, loosen the Handle (30) located at the rear of the Miter Saw. (See Figure P.) 3. Tilt the Back Rack (25) until the desired bevel ...

Page 21 - To replace the Motor Carbon Brushes:; two; The Carbon Brushes are located on; both; NOTE: New Carbon Brushes tend to arc or spark when first used; until; they; only; by a qualified service; PlEASE READ THE FOllOWINg CAREFUllY; FIgURE Q

Page 21 SKU 91995 For technical questions, please call 1-800-444-3353. 3. Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from the Miter Saw. Then, use a premium quality, lightweight machine oil to lubricate all moving parts except the Saw Blade (5). 4. To replace the Motor Ca...

Page 22 - PARTS lIST; available individually as replacement parts.

Page 22 SKU 91995 For technical questions, please call 1-800-444-3353. PARTS lIST NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Part # Description Part # Description 1 Handle 56 Saw Blade 2 Screw 57 Outer Flange 3 Sprin...

Page 23 - ASSEMBlY DIAgRAM; not available individually as replacement parts.

Page 23 SKU 91995 For technical questions, please call 1-800-444-3353. ASSEMBlY DIAgRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 110: WRENCH NOT SHOWN.