Chicago Electric 91995 - Manual
Chicago Electric 91995 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SPECIFICATIONS; UNPACKINg; When unpacking, check to make sure all the parts shown on the; Parts list on; SAVE THIS MANUAl; gENERAl SAFETY RUlES; WARNINg! Read all instructions; The term “power tool” in all of the warnings listed; SAVE THESE INSTRUCTIONS; WORK AREA; Keep your work area clean and well lit.; Cluttered benches and dark areas; Do not operate power tools in explosive atmospheres, such as in the; Power tools create sparks
- Page 4 – TOOl USE AND CARE
- Page 9 – gROUNDINg; Check with a qualified electrician if you are in doubt as to; grounded Tools: Tools with Three Prong Plugs; Grounded; WARNINg
- Page 10 – sure each cord contains at least the minimum wire size required.; RECOMMENDED MINIMUM WIRE gAUgE FOR EXTENSION CORDS*; Symbology
- Page 11 – ASSEMBlY AND OPERATINg INSTRUCTIONS; Assembly Diagram on page 24.; arrow
- Page 12 – CAUTION! The Cross Pin (28) should always be activated in the “locked; The Cross Pin allows the operator to lock the Saw Blade in position,; FIgURE E
- Page 13 – FIgURE g
- Page 14 – pointing
- Page 15 – To Assemble Additional Accessories:; FIgURE K; Safety Cover rotates back out of the way.; Do not disconnect or remove the Safety Cover (53). Do not operate the
- Page 16 – Never disconnect
- Page 17 – To Adjust The Cutting Depth:; WARNINg! Prior to performing this procedure, make sure the Power; Miter Saw is in operation.; FIgURE N
- Page 18 – To Adjust The Miter Angle:; To Adust The Bevel Of Cut:
- Page 19 – Make sure the Power Cord (102) of the Miter Saw is unplugged from its; Then, if necessary, make adjustments to the workpiece Holder; FIgURE P
- Page 21 – To replace the Motor Carbon Brushes:; two; The Carbon Brushes are located on; both; NOTE: New Carbon Brushes tend to arc or spark when first used; until; they; only; by a qualified service; PlEASE READ THE FOllOWINg CAREFUllY; FIgURE Q
- Page 22 – PARTS lIST; available individually as replacement parts.
- Page 23 – ASSEMBlY DIAgRAM; not available individually as replacement parts.
10” COMPOUND MITER SAW
Model
91995
SET UP AND OPERATINg INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
®
.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAl.
Copyright
©
2004 by Harbor Freight Tools
®
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised 07k
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 SKU 91995 For technical questions, please call 1-800-444-3353. SPECIFICATIONS Electrical Requirements 120 V / 60 Hz / 1800 Input Watts.15.0 AMPs Start Up / 5300 RPM No Load.Three Prong, Grounded, Power Cord Plug.Power Switch Type: Squeeze Type. Saw Blade (Included) Diameter/Type 10” Diameter ...
Page 4 SKU 91995 For technical questions, please call 1-800-444-3353. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. Remove adjusting key...
Page 9 SKU 91995 For technical questions, please call 1-800-444-3353. gROUNDINg Improperly connecting the grounding wire can result in electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with...
