Chicago Electric 90300 - Manuals

Page 2 - PRODUCT SPECIFICATIONS; Item; This product requires oil and fuel to be added before starting.; Fill the engine with the following:; Gal. of unleaded gasoline with no oil added; SAVE THIS MANUAL

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 2 PRODUCT SPECIFICATIONS Item Description Electrical Requirements 5400 Watt Surge Power 5 Min. Output @ 4400 Watts / Continuous Running Output 3600 Watts 15 AMPs @ 120V / 15 AMPs @ 240V 60 Hz Output 120V Dual Outlet: 15 AMP, 3 Prong...

Page 3 - GENERAL SAFETY RULES; READ AND UNDERSTAND ALL INSTRUCTIONS; WORK AREA; Keep your work area clean and well lit.

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 3 GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS WORK AREA 1. Keep your work area...

Page 6 - SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 6 2. Use eye and hearing protection. Wear ANSI approved safety impact eye goggles and hearing protection when using this product. ANSI approved safety impact eyegoggles and hearing protectors are available from Harbor Freight Tools....

Page 7 - Installation Precautions:

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 7 manual cannot cover all possible conditions and situations that may occur. Theoperator must understand that common sense and caution are factors which cannotbe built into this product, but must be supplied by the operator. Install...

Page 8 - Fire And Explosion Precautions:; Keep the Generator and surrounding area clean at all times.; Mechanical Precautions:

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 8 11. For trailer installation, the Generator should be mounted on the center point of thetrailer, over the wheels. 12. Install sound- and weatherproofing only while it is not raining or snowing to avoidtrapping moisture within the ...

Page 9 - Chemical Precautions:

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 9 2. Check for damaged par ts. Before using the Generator, any part that appearsdamaged should be carefully checked to determine that it will operate properly andperform its intended function. Check for alignment and binding of movi...

Page 10 - Electrical Precautions:; If an extension cord (not included) is used, make sure to use only UL; FIGURE A; REQUIRED MINIMUM EXTENSION CORD GAUGE – 120/ 240 VOLT

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 10 Electrical Precautions: 1. All connections and conduits from the Generator to the load must only be installedby trained and licensed electricians, and in compliance with all relevant local, state,and federal electrical codes and ...

Page 11 - INSTALLATION; The Generator weighs 155 pounds. Use care and the proper lifting

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 11 INSTALLATION 1. NOTE: Prior to powering tools and equipment, make sure the Generator’s rated voltage, wattage, and amperage capacity (120V/ 15 AMPs and 240V/ 15 AMPs) isadequate to supply all electrical loads that the unit will p...

Page 13 - OPERATING INSTRUCTIONS; Assembly Diagram; FIGURE C

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 13 OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 19. To Install A Battery: 1. NOTE: The Generator requires the installation of a 12 volt batt...

Page 14 - FIGURE D; FIGURE E

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 14 Pre-Start Checks: 1. NOTE: During operation, it may be necessary to refer to the Engine manufacturer’s Operation, Maintenance, and Parts manual (included) for detailed information aboutstarting, running, and stopping the Engine. ...

Page 15 - FIGURE F

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 15 To Start The Generator: 1. Turn the Fuel Valve (31) to its vertical“OPEN” position. (See Figure F.) 2. Move the Engine’s Choke all the wayto the left to its “START” position. (See Figure F.) 3. Turn the Engine’s “ON/OFF” switch t...

Page 16 - Powering Tools And Equipment:; The Generator features; FIGURE I; position, and remove the Ignition Key from the Ignition Switch

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 16 Powering Tools And Equipment: 1. Prior to powering tools and equipment, make sure the Generator’s rated voltage,wattage, and amperage capacity (120V/ 15 AMP and 240V/ 15 AMP) is adequateto supply all electrical loads that the uni...

Page 17 - Always turn off the Engine and remove the Ignition Key. Allow; inspect the general condition of the Generator. Check for; Do not use damaged equipment.; check to make sure the Engine’s oil level is adequate. Refer; PLEASE READ THE FOLLOWING CAREFULLY

SKU 90300 For technical questions, please call 1-800-444-3353. PAGE 17 INSPECTION, MAINTENANCE, AND CLEANING 1. NOTE: Preventative maintenance procedures and frequency will vary depending on the amount of Generator use. Refer to the Engine manufacturer’s Operation, Maintenance, and Parts manual (inc...