Chicago Electric 90186 - Manuals

Page 2 - READ AND UNDERSTAND ALL INSTRUCTIONS; WORK AREA; Keep your work area clean and well lit.; Cluttered benches and dark areas; Do not operate power tools in explosive atmospheres, such as in the; Power tools create sparks

PRODUCT SPECIFICATIONS SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front co...

Page 5 - SPECIFIC SAFETY RULES

22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 23. Use only accessories that are recommended by the manufact...

Page 7 - this product, but must be supplied the the operator.; outlet installed by a qualified electrician.

18. Always turn off the Circular Saw and unplug it from its electrical outlet before changing accessories or performing any inspection, maintenance, or cleaning procedures. 19. The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It m...

Page 8 - FIGURE A; to an electrically “live” terminal.; DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS; Canadian Standard Association, and the National Electrical Code.; FIGURE B

FIGURE A SKU 90186 PAGE 8 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” termina...

Page 9 - EXTENSION CORDS; can use either a two or three wire extension cord.; FIGURE C

SKU 90186 PAGE 9 EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately ...

Page 10 - SYMBOLOGY; UNPACKING; Parts List on page 17; ASSEMBLY INSTRUCTIONS; Assembly Diagram; prior; NOTE: Make sure to install the new Saw Blade with its

SKU 90186 PAGE 10 SYMBOLOGY Double Insulated Canadian StandardsAssociation UnderwritersLaboratories, Inc. Volts Alternating Current Amperes No Load Revolutionsper Minute (RPM) n o xxxx/min. A V ~ UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 17 and 18 are...

Page 11 - place by tightening; FIGURE D

SKU 90186 PAGE 11 3. Once the new Saw Blade (part #3) is installed onto the Shaft (part #15) place the Outer Blade Press (part #2) back onto the Shaft and secure the Saw Blade in place by tightening (counterclockwise) the Bolt (part #1) into the Shaft. (See Figure C.) LOCK BUTTON BOLT (#1) OUTER BLA...

Page 12 - OPERATING INSTRUCTIONS; , Shell Tivela Oil s680; plugged from its electrical outlet; FIGURE H

SKU 90186 PAGE 12 OPERATING INSTRUCTIONS Note: Add gear oil before first use. Check gear oil level before every use. Recommended Oil Harbor Freight Tools SKU 66582. In case of un-availability, you can use the following: Shell Valvata J680 ® , Mobilgear SHC680 ® , Shell Tivela Oil s680 ® . Always mak...

Page 13 - FIGURE I; Proper Operation During The Sawing Process:

SKU 90186 PAGE 13 The Power Switch: 1. To start the Circular Saw, depress the Safety Switch with your thumb, and then the Power Switch (part #67). To stop the tool, release pressure on the Power Switch. (See Figure I.) 2. WARNING! Prior to using the Circular Saw (each time), make sure the Switch Loc...

Page 14 - Make sure the Power Switch (part #67) of the Circular Saw is in its; “OFF”; inspect the general condition of the Circular Saw. Check; Do not use damaged equipment.; run the Saw in its continuous mode.

SKU 90186 PAGE 14 INSPECTION, MAINTENANCE, AND CLEANING 1. Make sure the Power Switch (part #67) of the Circular Saw is in its “OFF” position and that the tool is unplugged from its electrical outlet before per- forming any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect...

Page 15 - FIGURE J; To maintain peak efficiency of the Circular Saw’s Motor it; FIGURE K

3. TOOL LUBRICATION: Always check the oil level of the Circular Saw before each use. To check and add oil, make sure the Circular Saw is sitting on a flat, level surface. Remove the Oil Plug located at the front of the Circular Saw. The oil level should never be below the bottom threads of the Oil P...

Page 16 - PLEASE READ THE FOLLOWING CAREFULLY; The ventilation openings should be kept clean and free of dirt and

PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DIS-TRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE...

Page 17 - PARTS LIST

SKU 90186 PAGE 17 PARTS LIST Part# Description Qty 1 Bolt M8x20 1 2 Outer blade press 1 3 Saw blade φ185 1 4 Inner blade press 1 5 Check ring 1 6 Lower guard 1 7 Spring 1 8 Screw M5x18 4 9 Taper washer 5 10 Bearing cap 1 11 Bearing 60203 2 12 Oil seal φ35xφ22x7 1 13 Bearing set 1 14 Sheet oil seal 1...

Page 18 - LIMITED 90 DAY WARRANTY; which vary from state to state.

SKU 90186 PAGE 18 Part# Description Qty 81 Special nut 2 82 Check ring 2 83 Foot 1 84 Special bolt 1 85 Moving guard lever 1 86 Wrench 1 87 Rip fence 1 88 Screw M4x6 2 89 Pointer 1 90 Screw M5x12 1 91 Angle adjustment scale 1 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to ass...

Page 19 - DIAGRAM