Chicago Electric 41213 - Manuals

Chicago Electric 41213 – Manual in PDF format online.

Manuals:

Manual

Manual Chicago Electric 41213

Summary

Page 2 - saVE this ManUal; iMPortant saFEtY inForMation; dangEr; Notice

Page 2 SKU 41213 For technical questions, please call 1-800-444-3353. saVE this ManUal Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram...

Page 3 - gEnEral saFEtY rUlEs

Page 3 SKU 41213 For technical questions, please call 1-800-444-3353. gEnEral saFEtY rUlEs Warning! read all instructions Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. The term “power tool” in all of the warnings listed below refers to you...

Page 4 - Power tool use and care; disconnect the plug from the power source of the power tool before

Page 4 SKU 41213 For technical questions, please call 1-800-444-3353. Avoid accidental starting. Ensure the switch is in the off-position before plug- ging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. Remove any adjusti...

Page 5 - service; Vibration hazard; Maintain labels and nameplates on the tool

Page SKU 41213 For technical questions, please call 1-800-444-3353. service Have your power tool serviced by a qualified repair person using only identi - cal replacement parts. This will ensure that the safety of the power tool is maintained . Vibration hazard This tool vibrates during use. Repeate...

Page 7 - saVE thEsE instrUctions.

Page 7 SKU 41213 For technical questions, please call 1-800-444-3353. When using the polisher, maintain a firm grip on the tool with both hands to resist starting torque. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. Holding the work by h...

Page 8 - groUnding; Check with a qualified electrician if you are in doubt as to; grounded tools: tools with three Prong Plugs; double insulated tools: tools with two Prong Plugs; Warning

Page SKU 41213 For technical questions, please call 1-800-444-3353. groUnding improperly connecting the grounding wire can result in electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. do not modify the power cord plug provided with t...

Page 9 - Extension cords

Page 9 SKU 41213 For technical questions, please call 1-800-444-3353. dard Association, and the National Electrical Code. (see outlets for 2-Prong Plug.) Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (see outlets for 2-Prong Plug.) Extensio...

Page 10 - symbology

Page 10 SKU 41213 For technical questions, please call 1-800-444-3353. rEcoMMEndEd MiniMUM WirE gaUgE For EXtEnsion cords* (120/240 Volt) naMEPlatE aMPErEs (at full load) EXtEnsion cord lEngth 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 1 1 1 1 1 2.1 – 3.4 1 1 1 1 14 3. – .0 1 1 1 14 12 .1 – 7...

Page 11 - sPEciFications; UnPacKing; list of contents; sEt UP instrUctions; assembly

Page 11 SKU 41213 For technical questions, please call 1-800-444-3353. sPEciFications Electrical Requirements 110 V~ / 60 Hz / 6 A (load) Motor No Load Speed 2 Speed (200/ 3300) Arbor Diameter 7/” Spindle Thread /” - 11 UnPacKing When unpacking, check to make sure that the item is intact and undamag...

Page 12 - Figure 1

Page 12 SKU 41213 For technical questions, please call 1-800-444-3353. Depress the Stop Pin (3). Using the Wrench (49), Tighten the Flange Nut (47) by turning it clockwise until firmly in place. See Figure 1 below. Wrap a clean Polishing Bonnet (4) on top of the Backing Pad (4). Tie it se- curely us...

Page 13 - iMPortant; harbor Freight tools cannot be held responsible for damage; harbor Freight tools; oPErating instrUctions

Page 13 SKU 41213 For technical questions, please call 1-800-444-3353. controls Polishing Place a clean Polishing Bonnet (4) securely onto the Backing Pad (4). Tie it securely using the drawstring. Make sure to tuck any excess string inside the Bonnet note: Prior to waxing or polishing a vehicle, ma...

Page 15 - sanding

Page 1 SKU 41213 For technical questions, please call 1-800-444-3353. Place a sanding disk, with a hole in the center of it, onto the Backing Pad (4) and secure it with the Flange Nut (47). Tighten the Flange Nut (47) using the Spanner Wrench (49). See Assembly Diagram and Parts List pages 1 and 17....

Page 16 - MaintEnancE and sErVicing; replaced only by a qualified service technician.; troubleshooting

Page 1 SKU 41213 For technical questions, please call 1-800-444-3353. MaintEnancE and sErVicing risk of serious personal injury from accidental starting or electric shock. turn the Power switch of the tool to its “oFF” position and unplug the tool from its electrical outlet before performing any ins...

Page 17 - Parts list

Page 17 SKU 41213 For technical questions, please call 1-800-444-3353. Part # description Qty Part # description Qty 1 Screw 1 2 Brand 1 2 Washer 1 27 Washer 1 3 Stop Pin 1 2 Screw 1 4 Spring 1 29 Screw 1 Gear Box 1 30 Screw 1 Bearing 1 31 Cord Clip 1 7 Bearing Cover 1 32 Cord Armor 1 Screw 1 33 Cor...

Page 18 - assEMblY diagraM

Page 1 SKU 41213 For technical questions, please call 1-800-444-3353. assEMblY diagraM note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts.

Page 19 - liMitEd 90 daY WarrantY; PlEasE rEad thE FolloWing carEFUllY

Page 19 SKU 41213 For technical questions, please call 1-800-444-3353. record Product’s serial number here: note: If product has no serial number, record month and year of purchase instead. liMitEd 90 daY WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high qual...