Bakers Pride CB-MVPWDS - Manuals

Page 2 - When the oven arrives, it should consist of:; For a single unit: Refer to Figure 4

2 I. INSTALLATION INSTRUCTIONS SECTION ITEM PAGE A Receiving 2 B Set-up/Mounting 2 C Installation with Casters 3 D Location & Minimum Clearances 3 E Electrical Connections 4 F Flue Connection Ventilation 4 G Initial Cleaning 4 H System Check - Rotary Controls 5 II. OPERATING INSTRUCTIONS SECTION...

Page 4 - or transmitting stress to the electrical conduit.; Each oven requires separate electrical connections!; G. INITIAL CLEANING

4 E. ELECTRICAL CONNECTION: Install according to the spacing requirements listed in the installation section of this manual. We strongly recommend having a competent professional install this equipment. A licensed electrician should make the electrical connections and connect power to the unit. Loca...

Page 5 - IN THE EVENT OF POWER FAILURE, THE OVEN WILL NOT OPERATE.; See Operating/Programming Instruction Booklet for; II. OPERATING INSTRUCTIONS; oven to allow maximum air flow between them.; B. OPERATION SEQUENCE ROTARY CONTROL:

5 H. SYSTEM CHECK- ROTARY CONTROL (standard): (1) Open the oven door. (2) Turn Selector Switch to “HI.” The green indicator light near Selector Switch and oven light will illuminate. (3) Close the door. Oven lights will go off and fan will run. Make sure fan is rotating clockwise looking from front....

Page 6 - IMPORTANT FOR FUTURE REFERENCE; Model Number Serial Number Date Purchased

6 Timed cooking rotary control: (1) Close the oven doors.(2) Turn Selector Switch to “HI” or “LO” position. The indicator light near the Selector Switch will be illuminated.(3) Turn the thermostat knob to the desired cooking temperature.(4) Upon reaching the set temperature, the indicator light near...

Page 7 - submerge; CLEANING

7 OVEN INTERIOR: Clean The Racks And Rack Support Guides: Open the doors and remove all wire racks and rack support guides. Take them to the sink and thoroughly clean in warm water with mild detergent or soap. Use a nylon scouring pad or stiff nylon brush. DO NOT USE STEEL WOOL. Clean The Stainless ...

Page 8 - Cleaning The Blower Wheel; This product, when stacked, has more than one power-supply; Blower Wheel; Figure 2; Assembly Instructions; : Place undershelf between; Oven Base

8 D. SERVICING: NOTE: THIS APPLIANCE MUST BE SERVICED BY AN AUTHORIZED SERVICE AGENT. (1) Power supply to the unit must be disconnected before any service is performed.(2) Most of the service on the unit can be performed from the front and/or control panel side.(3) For proper servicing, access to th...

Page 9 - Figure 3; Item 1

9 Figure 3 Item 1 Item 2 Item 3 E3770A E3771A 3/8”-16 Bolt STACKING INSTRUCTIONS FOR: COB-E & COM-E CONVECTION OVENS Remove flue from top oven and replace with item 1 2 1 3 Attach part # 21818062 with 6 each 8-32 stainless screws Material: 14 ga 201 Stainless Remove flue from bottom oven, and re...

Page 10 - Foot Insert, Adjustable; Item

WITH PLATE CASTER WITHOUT PLATE CASTER Figure 4 LEG ASSEMBLY INSTRUCTIONS - MODEL: COB-E & COM-E 1. Attach four item 2 to four item 1 using item 3, 4 and 5. 2. Using proper lifting equipment attach item 1 to the corresponding hole patterns located in the bottom of the oven with item 6. 1 2179681...

Page 13 - Single Phase 208V or 240V Wiring Diagram (CH-100 Control)

13 PROBE DOOR HEAT FAN LIGHTS POWER COM REL AY L1 L3 L 2 SINGLE PHASE 208/ 240V DOORS ACTIVATESWITCH WHEN CLOSED GND FRONT ELEMENT 28 29 10 9 16 17 14 15 27 4 21 20 26 25 23 22 18 2 1 27 24 19 8 6 9 12 13 FUSE BOX C NO NC MOTOR T3 TO T2 T1 TO T4 T1 TO T2 A1 A2 32 35 33 34 36 37 4 POLES, 40 AMPS CONT...

Page 14 - DET; Steam; Description; Kits; PA

14 86 1 89 1 12 0 1 11 9 1 10 7 1 91 1 11 8 1 10 1 1 85 1 11 2 2 11 3 2 11 5 2 32 2 29 1 27 5 50 6 52 1 53 1 5 1 43 1 50 6 49 2 54 2 11 4 2 21 2 11 1 1 45 1 61 1 79 4 76 8 80 1 17 2 83 2 60 2 12 1 3 63 6 4 1 31 1 37 1 62 1 34 1 20 1 75 1 47 1 58 1 24 1 72 1 74 1 9 1 1 23 1 33 1 71 2 69 1 11 1 30 1 1...

Page 16 - BKI LIMITED WARRANTY

16 WHAT IS COVERED This warranty covers defects in material and workmanship under normal use, and applies only to the original purchaser providing that: ♦ The equipment has not been accidentally or intentionally damaged, altered or misused; ♦ The equipment is properly installed, adjusted, operated a...